Honeywell Performance HEW2PER2 Bruksanvisning

Honeywell övervakningskamera Performance HEW2PER2

Läs nedan 📖 manual på svenska för Honeywell Performance HEW2PER2 (2 sidor) i kategorin övervakningskamera. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

HEW2PER2 WDR 4 MP IR Bullet Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series IP

camera. Follow the instructions in this guide to install and log in

to your camera. For instructions on configuring the camera,

refer to the Performance Series IP Cameras User Guide on the

installation CD that came with your camera.

If you require additional assistance, contact Tech Support

(contact info is listed on the back page).

Cautions and Warnings

WARNING

To ensure compliance with electrical safety standards, this product is intended for

use with a Listed Power Adapter marked “Limited Power Source” or “LPS” on the unit,

output rated to 12 VDC, minimum 0.33 A, TMA=60 deg C, or from Power over

Ethernet (PoE) provided by Listed Information Technology Equipment meeting IEEE

802.3af PoE standard.

WARNING

The Ethernet connection is not intended to be connected to exposed (outside plant)

networks. Do not connect two power sources to the camera at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

• Read and keep these instructions.

• Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager. Avoid operating the unit under or close to unstable light sources (may cause

flickering), or close to fluorescent lamps or objects reflecting light.

• Do not touch the camera lens.

• Do not drop the camera or subject it to physical shock.

• Do not use a strong or abrasive detergent when cleaning the camera.

• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where

the operating temperature is outside the recommended range of -22°F to 140°F (–30°C to

60°C).

Note

Do not apply power to the camera before completing installation.

Confirm the installation surface can support at least three times the weight of the

camera.

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts are missing

or damaged, contact your dealer immediately.

• Camera

• Installation CD

• Quick installation guide

• Allen key (L- wrench)

• Self-tapping screws (×4)

• Plastic wall anchors (×4)

• Mounting template

Preparing the Mounting Surface

Inspect the site where you want to install the camera. The mounting

surface must be flat and capable of supporting at least three times

the weight of the camera.

Remove the backing from the mounting template sticker and affix

the sticker to the mounting surface.

Note If you are using the side exit for the cable, note the

orientation of the cable exit notch. In outdoor installations the notch

should point downwards to prevent water from entering the camera

housing.

Drill three screw holes at the locations indicated on the mounting

template sticker and insert the three supplied plastic anchors in the

holes.

If you are flush mounting the camera and want to store the cables

inside the wall or ceiling, drill a hole at the cable exit position on the

mounting template and then pull the cables through the hole.

CAUTION

THIS SYMBOL INDICATES THAT

DANGE OUSR VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

CA : TUTION O REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REM THE COVE OVER.

NO USER-SERVICEABLE PAR .TS INSIDE

REFER SER TO QU RVICING ALIFIED SE VICE

PERSONNEL.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY T.THIS UNI

RISK OF ELECTRIC

SHOCK

DO N T OPENO

© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell

cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.

Mounting the Camera

1. Loosen the locking screw on the camera enclosure to remove

the enclosure from the camera base.

2. If local storage is needed, insert a m icroSD card into the

m icroSD card slot ( ). refer to the right picture

3. Route the cables through the camera base.

4. Align the screw holes on the camera base with the plastic wall

anchors.

5. Attach the camera base to the mounting surface using the

supplied screws.

6. Connect the camera with the Ethernet cable and the power

cable.

a. Connect one end of the Ethernet cable to the RJ-45 port

on the camera.

b. If the other end of the Ethernet cable is NOT connected to

a PoE (Power-over-Ethernet) switch or NVR, connect the

power connector of the camera to a 12 VDC power source.

7. Reattach the enclosure to the base and tighten the locking

screw.

8. Rotate the camera body to the desired position.

Adjusting Zoom and Focus

If the camera a is connected to the PoE port of Honeywell Embedded NVR, you can log on to the

camera directly from the NVR.

To log on to the camera from a : PC

1. Install the Honeywell Config Tool from the installation CD.

2. Use the Config Tool to discover the camera and open the camera’s webpage.

3. Log on to the camera as the admin user. The default user name is admin -(case sensitive) and

the default password is 1234.

Note • Be sure to remember the password of the camera. If the password is lost, the

camera may need to be sent back to the factory for recovery.

• Only Internet Explorer 11 (or later) is supported.

• IP address of the device is assigned automatically by DHCP server. If the DHCP

server is not available, the device will acquire 192.168.1.108 as the default IP

address.

4. Go to Setup 



Camera



Conditions



Zoom and Focus. The following panel appears:

• Click Zoom in Zoom out + or - to zoom in or out.

• Click Near - or Far + to focus near or far, or click to enable auto focus.Auto Focus

Recommended Recorders

HEN*4

8/16/32/64-channel Focus 4K NVRs (H.264 and H.265)

HEN*3 4/8/16/32 (H.264 -channel Performance Series NVRs ) and H.265

HEN*2 4/8/16 - channel Performance Series NVRs (H.264)

HRHT4* - 4/8/16 channel 4 MP HQA/IP/CVBS Hybrid DVRs (H.264)

Regulatory Statements

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Note Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES- 003.

Manufacturer’s Declaration of Conformance

North America ied with this guide conforms to UL 60950The equipment suppl -1 and CSA C22.2 No.

60950 1.-

Europe The manufacturer declares that the equipment supplied is compliant with the European

Parliament and Council Directive on the restriction of the use of certain hazardous substances in

electrical and electronic equipment (2011/65/EU), General Product Safety Directive (2001/95/EC), and

the essential requirements of the EMC directive (2014/30/EU), conforming to the requirements of

standards EN 55032 for emissions, EN 50130 4 for immu- nity, and EN 62368-1 for electrical equipment

safety.

WEEE (Waste Electrical and Electronic Equipment)

Correct disposal of this product (applicable in the European Union and other European

countries with separate collection systems). This product should be disposed of, at the end of

its useful life, as per applicable local laws, regulations, and procedures.

Honeywell

2700 Blankenbaker Pkwy,

Suite 150

Louisville, KY, 40299, USA

www.honeywell.com/security

+1 800 323 4576

(North America only)

Aston Fields Road, Whitehouse

Industrial Estate

Runcorn, Cheshire, WA7 3DL, UK

www.honeywell.com/security/uk

+1 44 (0) 1928 754 028

(Europe only)

Building #1, 555 Huanke Road,

Zhang Jiang Hi- Tech Park

Pudong New Area, Shanghai,

201203, China

www.asia.security.honeywell.com

+400 840 2233

(Asia Pacific only)

Document 800-2459 /20182 – – 08Rev A

Produktspecifikationer

Varumärke:	Honeywell
Kategori:	övervakningskamera
Modell:	Performance HEW2PER2
Färg på produkten:	Zwart
Förpackningens bredd:	96 mm
Djuppackning:	230 mm
Förpackningshöjd:	240 mm
Ljudformat som stöds:	MP3, WMA
Typ av anslutningskontakt:	3,5 mm
Antal HDMI-portar:	1
Genomsnittlig effekt:	280 W
Hörlursutgångar:	1
Luidsprekers:	2-weg
Antal SCART-portar:	1
Ljudutgångskanaler:	- kanalen
Frekvensomfång:	20 - 20000 Hz
Mediatyper som stöds:	MP3-CD, WMA, CD-R / CD-RW, DVD, Dvix
Inklusive DVD-spelare/inspelare:	DVD speler
Mått (B x D x H):	262 x 135 x 200 mm
Inkluderar RDS-tuner:	Ja
Total harmonisk distorsion (THD):	0.5 procent
Subwoofer impedans:	4 Ohm
Satellithögtalarimpedans:	8 Ohm