Hotpoint HIO 3P23 WLE - Ultima Bruksanvisning

Hotpoint Diskmaskin HIO 3P23 WLE - Ultima

Läs nedan 📖 manual på svenska för Hotpoint HIO 3P23 WLE - Ultima (8 sidor) i kategorin Diskmaskin. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

DAILY REFERENCE

GUIDE

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

You can download the Safety Instructions and the Use

and Care Guide, by visiting our website

docs.hotpoint.eu and following the Instructions on the

back of this booklet.

Before using the appliance carefully read Health and Safety guide.

PRODUCT DESCRIPTION

APPLIANCE

1. Upper rack

Cutlery rack

3. Foldable flaps

4. Upper rack height adjuster

5. Upper spray arm

6. Lower rack

7. Space Zone

8. Lower spray arm

9. Filter Assembly

10.Salt reservoir

11.Detergent and Rinse Aid dispensers

12.Rating plate

13.Control panel

0000 000 00000

Service:

CONTROL PANEL

1. On-Off/Reset button with indicator light

2. Program selection button

3. Salt refill indicator light

4. Rinse Aid refill indicator light

5. Program number and remaining time indicator

6. Delay indicator light

7. Display

8. Zone Wash 3D indicator light

9. Delay button

10.

Zone Wash 3D

button

11. Tablet (Tab) button with indicator light

12. Turbo button with indicator light

13. Extra Dry button with indicator light

1 2 3 4 5 6 7 8 9 10 11 12 13

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see

PROGRAMS DESCRIPTION) and should be filled when the SALT REFILL

indicator light in the control panel is lit.

1.Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2.Position the funnel

(see figure)

and fill the salt

reservoir right up to its edge (approximately 1 kg);

it is not unusual for a little water to leak out.

3.Remove the funnel and wipe any salt residue

away from the opening.

4. Remove the funnel and wipe any salt residue away from the

opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, we recommend carrying out the

procedure before the washing cycle is started.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is for average (3) water hardness.

• Switch on the appliance by pressing the ON/OFF button.

• Switch off the appliance by pressing the ON/OFF button.

• Hold down button P for 5 seconds, until you hear a beep.

• Switch on the appliance by pressing the ON/OFF button.

• The current selection level number and the salt indicator light both flash.

• Press button P to select the desired hardness level (see WATER

HARDNESS TABLE).

• Switch off the appliance by pressing the ON/OFF button.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specifically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL

indicator light switches off.

If the salt container is not filled, the water softener and the heating

element may be damaged as a result.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser A should

be filled when the RINSE AID REFILL indicator light in the control

panel is lit.

1. Open the dispenser

by pressing and pulling up the tab on the lid.

2. Carefully introduce the rinse aid as far as the maximum (110 ml)

reference notch of the filling space - avoid spilling it. If this happens,

clean the spill immediately with a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satisfied with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.

• Switch it off using the ON/OFF button.

• Press button P three times - a beep will be heard.

• Switch it on using the ON/OFF button.

• The current selection level number and rinse aid indicator light flash.

• Press button P to select the level of rinse aid quantity to be

supplied.

• Switch it off using the ON/OFF button

Setting is complete!

If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied. The

LOW RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 4 levels can be set according to the dishwasher model.

The factory setting is for a medium level.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes, set a

high number (3-4).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser

use the opening device A. Introduce

the detergent into the dry dispenser

B only. Place the amount of

detergent for pre-washing directly

inside the tub.

1.When measuring out the detergent

refer to the mentioned earlier

information to add the proper

quantity. Inside the dispenser

there

are indications to help the detergent dosing.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the

TABLET

button, because it adjusts the program so that the best washing and

drying results are always achieved.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 17 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

PROGRAMS TABLE

ECO program data is measured under laboratory conditions according to European Standard EN 50242.

*) Not all options can be used simultaneously.

**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary

depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,

load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W

Program

Drying

phase

Available options *)

Detergent

container Duration of

wash program

(h:min)**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

Tub B

1. Eco 50° 3:15 11 0.95

2. Auto Intensive 65° - 2:00 - 3:10 14 - 17 1.50 - 1.85

3. Auto Normal 55° 1:30 - 2:30 14.5 - 16 1.15 - 1.30

4. Auto Fast 50° - - 0:40 - 1:20 13 - 14.5 1.15 - 1.25

5. Express 30’ 50° - - 0:30 9 0.50 - 0.55

6. Good Night 50° - 3:30 15 1.15

7. Sanitizing 65° - 1:40 10 1.30

8. Soak - - - - 0:12 4.5 0.01

9. Self- Clean 65° - - 0:50 8 0.80 - 0.85

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

ECO

Normally soiled crockery. Standard program, the most efficient in terms

of its combined energy and water consumption.

AUTO INTENSIVE

Heavily soiled dishes and pans (not to be used for delicate items).

AUTO NORMAL

Automatic program for normally soiled pans and dishes.

AUTO FAST

Limited quantity of daily soiling (ideal for 4 place settings).

EXPRESS 30’

Program to be used for lightly-soiled dishes with no dried food

residues. (Ideal for 2 place settings).

GOOD NIGHT

Suitable for night-time operation of the appliance. Optimum

performance ensured.

SANITIZING

Normally or heavily soiled crockery, with additional antibacterial wash.

SOAK

Crockery to be washed later. No detergent to be used with this

program.

SELF-CLEAN

Program to be used to perform maintenance of the dishwasher. It

cleans the interior of the appliance using hot water.

Notes:

Optimum performance levels when using the “Auto Fast” and “Express”

programs can be achieved by observing the maximum amounts of

specified place settings.

To reduce consumption even further, only run the dishwasher

when it is full.

Produktspecifikationer

Varumärke:	Hotpoint
Kategori:	Diskmaskin
Modell:	HIO 3P23 WLE - Ultima
Bredd:	305 mm
Djup:	267 mm
Blåtand:	Ja
Wi-Fi-standarder:	802.11a, 802.11b, 802.11g, Wi-Fi 5 (802.11ac), Wi-Fi 6E (802.11ax)
Ethernet LAN:	Ja
Antal USB 2.0-portar:	2
Antal HDMI-portar:	1
Antal Ethernet LAN (RJ-45)-portar:	2
Hörlursutgångar:	1
WiFi-standard:	Wi-Fi 6E (802.11ax)
Stöder Windows:	Windows 10 x64, Windows 11 x64
Antal portar USB 3.2 Gen 1 (3.1 Gen 1) Typ A:	6
Processoruttag:	LGA 1700
Processorfabrikant:	Intel
Maximalt internminne:	128 GB
Ljudutgångskanaler:	5.1 kanalen
Ethernet-gränssnittstyp:	2.5 Gigabit Ethernet
Linjeingång:	Ja
Chipset moderkort:	Intel Z790
Antal portar USB 3.2 Gen 2 (3.1 Gen 2) Typ A:	2
Typ av minnesplats:	DIMM
Ljudchip:	Realtek ALC4082
S/PDIF-utgång:	Ja
RAID-stöd:	Ja
Minneskanal:	Dubbelkanaals
Gränssnitt för lagringsenheter som stöds:	M.2, SATA III
Antal Thunderbolt-portar:	2
Komponent för:	PC
LAN-kontroller:	Killer E3100G
Typer av RAID:	0, 1,5, 10
Antal SATA III-kontakter:	8
Icke-ECC:	Ja
Kompatibla processorer:	Intel Core i5, Intel Core i7, Intel Core i9
Minnestyper som stöds:	DDR5-SDRAM
Max. antal SMP-processorer:	1
Wifi:	Ja
Typer av lagringsenheter som stöds:	HDD & SSD
Moderkort chipset familj:	Intel
Moderkorts formfaktor:	Verlengd ATX
Antal minnesplatser:	4
BIOS-typ:	UEFI AMI
BIOS-minnesstorlek:	256 Mbit
Anslutning för CPU-kylare:	Ja
ATX-strömkontakt (24-stift):	Ja
USB 2.0-anslutningar:	2
Anslutning för ljudpanel på framsidan:	Ja
Obuffrat minne:	Ja
USB 3.2 Gen 1 (3.1 Gen 1) anslutningar:	2
TPM-kontakt:	Ja
Antal M.2 (M) platser:	1
RGB LED anslutningsskena:	Ja
PCI Express x16 (Gen 4.x)-platser:	1
USB 3.2-kontakter (3.1 Gen 2):	1
PCI Express x16 (Gen 5.x)-platser:	2