Hudson Valley Williamsburg 1057-AGB Bruksanvisning

Hudson Valley Lättnad Williamsburg 1057-AGB

Läs nedan 📖 manual på svenska för Hudson Valley Williamsburg 1057-AGB (2 sidor) i kategorin Lättnad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
FIXTURE INSTALLATION
1. Feed the wire through the STEM (6) and twist tightly onto the FIXTURE ASSEMBLY (10). Keep adding
additional stems until you desired hanging height is met.
2. Slide in CANOPY(7) onto the STEM (6), and thread the 1/4 NIPPLE (5) onto the top end of the STEM (6)
3. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the
MOUNTING SCREWS (2). This fixture is designed to be mounted on standard round or octagon junction box.
The junction box must be securely mounted to the structure of the building.
4. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire 5
8".
5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the
GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED
WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same
as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD
RESULT IN SERIOUS INJURY OR DEATH!
8. Push the wires back into the junction box. Lift up the CANOPY (7) up to the ceiling, and secure it with the
HEADLESS SCREW (8) by using supplied ALLEN KEY TOOLING (9) .
9. Attach the SHADE (12) to the FIXTURE ASSEMBLY (10) and secure with the TOP FINIAL (11) .
10. Screw the BULB (13) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 9 WATT LAMP. DO
NOT EXCEED THE RECOMMENDED WATTAGE!
11. Lift the DIFFUSER (14) up onto the fixture and secure using the BOTTOM FINIAL (15) .
12. Restore power to the outlet at the breaker or fuse box.
WILLIAMSBURG
1057
INSTALLATION INSTRUCTIONS
WARNING/CAUTION
·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS
COMPLETELY BEFORE STARTING INSTALLATION.
·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.
·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS
AFTER USE.
·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE
CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR
TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE
TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
www.hvlgroup.com
Questions? We're here to help!
Contact us at CustomerService@hvlgroup.com
1
2
34
5
6
7
8
9
10
11
12
13
14
15
ITEM DESCRIPTION PART NUMBER
1MOUNTING PLATE HDW-001046
2MOUNTING SCREW HDW-001046
3GROUND SCREW HDW-001046
4WIRE NUT HDW-001046
51/4 NIPPLE HDW-001046
6STEM STM-104603,06,12,18
7CANOPY CAS-001046
8HEADLESS SCREW CAS-001046
9ALLEN KEY TOOLING MIS-001046
10 FIXTURE ASSEMBLY FAS-001057
11 TOP FINIAL FIN-001002-T
12 SHADE SHD-001057
13 A15 LED BULB NOT INCLUDED
14 DIFFUSER DIF-001057
15 BOTTOM FINIAL FIN-001002-B
FIXTURE INSTALLATION
1. Feed the wire through the STEM (6) and twist tightly onto the FIXTURE ASSEMBLY (10). Keep adding
additional stems until you desired hanging height is met.
2. Slide in CANOPY(7) onto the STEM (6), and thread the 1/4 NIPPLE (5) onto the top end of the STEM (6)
3. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the
MOUNTING SCREWS (2). This fixture is designed to be mounted on standard round or octagon junction box.
The junction box must be securely mounted to the structure of the building.
4. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire 5
8".
5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the
GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED
WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same
as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD
RESULT IN SERIOUS INJURY OR DEATH!
8. Push the wires back into the junction box. Lift up the CANOPY (7) up to the ceiling, and secure it with the
HEADLESS SCREW (8) by using supplied ALLEN KEY TOOLING (9) .
9. Attach the SHADE (12) to the FIXTURE ASSEMBLY (10) and secure with the TOP FINIAL (11) .
10. Screw the BULB (13) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 9 WATT LAMP. DO
NOT EXCEED THE RECOMMENDED WATTAGE!
11. Lift the DIFFUSER (14) up onto the fixture and secure using the BOTTOM FINIAL (15) .
12. Restore power to the outlet at the breaker or fuse box.
WILLIAMSBURG
1057
INSTALLATION INSTRUCTIONS
www.hvlgroup.com
Questions? We're here to help!
Contact us at CustomerService@hvlgroup.com
1
2
34
5
6
7
8
9
10
11
12
13
14
15
ITEM DESCRIPTION PART NUMBER
1MOUNTING PLATE HDW-001046
2MOUNTING SCREW HDW-001046
3GROUND SCREW HDW-001046
4WIRE NUT HDW-001046
51/4 NIPPLE HDW-001046
6STEM STM-104603,06,12,18
7CANOPY CAS-001046
8HEADLESS SCREW CAS-001046
9ALLEN KEY TOOLING MIS-001046
10 FIXTURE ASSEMBLY FAS-001057
11 TOP FINIAL FIN-001002-T
12 SHADE SHD-001057
13 A15 LED BULB NOT INCLUDED
14 DIFFUSER DIF-001057
15 BOTTOM FINIAL FIN-001002-B
ATTENTION PRUDENCE
·DÉBRANCHEZ L'ALIMENTATION AVANT DE REMPLIR OU DE CÂBLER LE LUMINAIRE. LISEZ
COMPLÈTEMENT TOUTES LES INSTRUCTIONS AVANT DE COMMENCER L'INSTALLATION
·POUR ÉVITER LE RISQUE D'INCENDIE OU D'ÉLECTROCUTION, LE LUMINAIRE DOIT ÊTRE INSTALLÉ
CONFORMÉMENT À TOUS LES CODES ÉLECTRIQUES/DE CONSTRUCTION NATIONAUX ET LOCAUX
APPLICABLES. L'INSTALLATION ET L'ENTRETIEN DE CET APPAREIL DOIVENT ÊTRE EFFECTUÉS PAR UN
ÉLECTRICIEN AGRÉÉ OU UN TECHNICIEN CERTIFIÉ FORMÉ EN USINE.
·CALIFORNIE PROP 65 : CET APPAREIL D'ÉCLAIRAGE CONTIENT DES PRODUITS CHIMIQUES CONNUS PAR
L'ÉTAT DE CALIFORNIE POUR PROVOQUER LE CANCER, DES MALADIES CONGÉNITALES ET/OU D'AUTRES
DOMMAGES À LA REPRODUCTION. LAVER LES MAINS APRÈS UTILISATION.
·RETIRER LE LUMINAIRE, LES PIÈCES ET LE(S) SAC(S) DE PIÈCES DU CARTON. AVANT DE JETER LE
CARTON, VÉRIFIEZ DOUBLE POUR VOUS ASSURER QUE TOUTES LES PIÈCES SONT TROUVÉES.
INSPECTER LE LUMINAIRE AVANT L'INSTALLATION POUR TOUT DOMMAGE AU LUMINAIRE.
·GRADATION : LE LUMINAIRE PEUT ÊTRE CONTRLÉ PAR UN DISPOSITIF DE GRADATION MURALE. UTILISER
UNIQUEMENT UN GRADATEUR TRIAC/ÉLECTRONIQUE. ASSUREZ-VOUS QUE LE CARTON EST MARQUÉ
POUR UNE UTILISATION AVEC UNE SOURCE DE LUMIÈRE FLUORESCENTE À INCANDESCENTE COMPACTE
UNIQUEMENT. CEUX-CI PEUVENT ÊTRE FOURNIS PAR VOTRE DISTRIBUTEUR ÉLECTRIQUE LOCAL,
CENTRE À DOMICILE OU MAGASIN DE QUINCAILLERIE.
·VEUILLEZ NETTOYER UNIQUEMENT AVEC UN CHIFFON DOUX ET SEC ! N'UTILISEZ PAS DE NETTOYANTS

Produktspecifikationer

Varumärke: Hudson Valley
Kategori: Lättnad
Modell: Williamsburg 1057-AGB

Behöver du hjälp?

Om du behöver hjälp med Hudson Valley Williamsburg 1057-AGB ställ en fråga nedan och andra användare kommer att svara dig


Lättnad Hudson Valley Manualer

Hudson Valley

Hudson Valley Rye 2314-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Geneva 712-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Amboy 1548-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Greenwich 8301-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Newport 6513-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Geneva 709-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Brookhaven 7215-VGL Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Geneva 715-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley White Plains 5210-AGB Bruksanvisning

5 Januari 2025
Hudson Valley

Hudson Valley Avondale 1753-AGB Bruksanvisning

5 Januari 2025

Lättnad Manualer

Nyaste Lättnad Manualer

BeamZ

BeamZ LED TRIPLE FLEX CENTRE PRO Bruksanvisning

7 Januari 2025
BeamZ

BeamZ BTSE200 Bruksanvisning

7 Januari 2025
BeamZ

BeamZ Cobra Wash100 Bruksanvisning

7 Januari 2025
Kogan

Kogan KASMFSTN15A Bruksanvisning

7 Januari 2025
BeamZ

BeamZ Cobra Wash120 Bruksanvisning

7 Januari 2025
Kogan

Kogan KBE14CWWT1A Bruksanvisning

7 Januari 2025
BeamZ

BeamZ IGNITE300A Bruksanvisning

7 Januari 2025
Kogan

Kogan KALAMPMS31B Bruksanvisning

7 Januari 2025
Sun Joe

Sun Joe 24V-LGT500-LTE Bruksanvisning

7 Januari 2025
Infinity

Infinity iM-2515 Bruksanvisning

6 Januari 2025