Icom HM-162B SW Bruksanvisning
Icom
Ljud/videomottagare
HM-162B SW
Läs nedan 📖 manual på svenska för Icom HM-162B SW (8 sidor) i kategorin Ljud/videomottagare. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/8
INSTRUCTIONS
REMOTE-CONTROL MICROPHONE
HM-162B/SW
Thank you for purchasing the HM-162B/SW
REMOTE
-
CONTROL MICROPHONE
. The COMMANDMIC IIITM is a
remote control microphone for use with the IC-M604
or else.
Please read the connected transceiver’s instruction
manual carefully before installation and operation.
These instructions are just described the remote-
control operations only.
qBUSY/TRANSMIT INDICATOR
➥“BBUUSSYY” appears when receiving a signal or when the
squelch opens.
➥“TTXX” appears while transmitting.
wRECEIVER ATTENUATOR INDICATOR
“LLOOCC” appears when the Attenuator function is in use.
eSCRAMBLER INDICATOR
“SSCCRRAAMM” appears when an optional voice scrambler is acti-
vated.
rSCAN INDICATOR
➥Either “NNOORRMMAALL SSCCAANN” or “PPRRII--SSCCAANN 1166” scan type
appears while scanning.
➥“DDUUAALL 1166” appears during dualwatch; “TTRRII 1166” ap-
pears during tri-watch.
tSELECTOR STATUS INDICATOR
Indicates the [SELECTOR] active status;
“[[VVOOLL]]” appears when [SELECTOR] as the audio volume.
“[[SSQQLL]]” appears when [SELECTOR] as the noise squelch
controller.
“[[CCHH ]]” appears when [SELECTOR] as the channel selector.
yPOSITION INDICATOR
➥Shows the GPS position data.
•“
????” may blink every 2 sec. instead of position data when
the GPS position data is invalid. In this case, the last position
data is held for up to 23.5 hours.
•“
????” may blink every 2 sec. instead of position data 4 hours
after the position data is input manually, up until 23.5 hours
have past.
➥“NNoo PPoossiittiioonn” appears when no GPS receiver is con-
nected and no position data is input manually.
uTIME ZONE INDICATOR
➥“LLooccaall” appears when the offset time data in the ‘Set
up’ menu is entered.
➥“NNoo TTiimmee” appears when no GPS receiver is connected
and no time data is input manually.
iCHANNEL COMMENT INDICATOR
Channel comment appears, if programmed.
oCHANNEL NUMBER READOUT
Indicates the selected operating channel number.
!0 KEY LOCK INDICATOR
➥Appears while the Key Lock function is in use.
➥Blinks while the All Key Lock function is in use.
!1 LOW BATTERY INDICATOR
“” blinks when the battery voltage drops to approx. 10 V
DC or below.
!2 CALL CHANNEL INDICATOR
➥
“CCAALLLL” appears when the call channel is selected.
➥“AALLEERRTT” appears when the Weather Alert function is in
use; blinks when an alert tone is received.
!3 CHANNEL GROUP INDICATOR
Indicates whether an International “IINNTT,” U.S.A. “UUSSAA,”
Canadian “CCAANN” or weather “WWXX” channel is selected.
!4 DUPLEX INDICATOR
Appears when a duplex channel is selected.
•Duplex channel has a different TX and RX frequency.
!5 TAG CHANNEL INDICATOR
Appears when a tag channel is selected.
!6 POWER INDICATOR
➥“2255WW” appears when high power is selected.
➥“11WW” appears when low power is selected.
!7 RX SPEAKER INDICATOR
Appears when an RX speaker function is activated.
BUSYBUSY-25W25W------INTINT------CALLCALL
LOCLOC- -- -- DUPDUP
SCRAMSCRAM--TAGTAG
NORMALNORMAL-SCANSCAN
-3434°34.506N34.506N
123123°23.236W23.236W
LocalLocal----1:101:10- - CALLINGCALLING
RXRX
[VOL]
w
q
e
y
u
r
t
!6!7 !4!5 !3 !2
o
!0
!1
i
Accessories included with the HM-162B/SW: Qty.
qConnection cable (OPC-1540*: 6 m; 20 ft) ....................... 1
wMounting base .................................................................. 1
eConnector cap .................................................................. 1
rMicrophone hanger .......................................................... 1
tScrews (M3 ×16; tapping) ............................................... 5
*: OPC 1540 has external speaker leads as illustrated at right.
(Yellow: Audio, Black: Speaker ground)
These instructions are described when the HM-162 is connected to the IC-M604. Some operations or indications may be dif-
ferent as these instructions depending on the connecting transceiver.
xFunction display
zHM-162B/SW supplied accessories
qwe
r
t
Yellow Black
1
The optional HM-162 remotely controls the transceiver and pro-
vides an optional Intercom function.
qDISTRESS KEY [DISTRESS]
Push for 5 sec. transmit a Distress call.
wTRANSMIT POWER KEY [H/L]
➥Push to toggle high or low power.
•Some Channels are set to low power only.
➥While pushing this key, other keys perform secondary
functions.
➥While pushing this key, turn power ON to toggle the All key
Lock function ON or OFF.
•“ ” blinks while the All key Lock function is in use.
•Only [PWR] ([CLR]/[MENU]), [DISTRESS] and [PTT] are
functional when the All key Lock function is in use.
ePTT SWITCH [PTT]
Push and hold to transmit; release to receive.
rSELECTOR DIAL [SELECTOR]
➥
Rotate to adjust the audio level
, or select the items in DSC
menu, Set mode settings in set mode, etc.
➥Rotate to select the noise squelch level or operating chan-
nel after pushing
[VOL/SQL•MONI ].
➥Rotate to adjust the brightness of the LCD and key back-
light while pushing [H/L].
➥Checks TAG channels or changes scanning direction dur-
ing scan.
➥Rotate to adjust the audio level during in hailer mode.
➥Rotate [SELECTOR] then push [ENT] to adjust the audio
level during in RX Speaker mode.
tENTER KEY [ENT]
➥Push to fix the selected contents, or select Set mode set-
tings, etc.
➥Push for 1 sec. to indicate the GPS information of the con-
nected transceiver.
•No information appears when GPS receiver is not con-
nected to the transceiver.
yCLEAR•POWER KEY [CLR•PWR]
➥While HM-162’s power is OFF, push this key and [MENU]
for 1 sec. to turn the power ON.
•The connected transceiver power is also turned ON, if it’s
OFF.
➥While HM-162’s power is ON;
●
●
While pushing this key, push [MENU] to turn the HM-
162 power OFF.
•The connected transceiver power is also turned OFF de-
pending on the transceiver’s Set mode setting.
●
●
Push to clear the selected contents, or select Set mode
settings, etc.
uDSC MENU KEY [MENU]
➥Toggles the DSC menu ON or OFF when pushed.
➥While pushing [CLR], push this key to turn the HM-162
power ON and OFF.
iSCAN KEY [SCAN•TAG]
➥Push to start and stop Normal or Priority scan when TAG
channels are programmed.
➥Push for 1 sec. to set the displayed channel as a TAG
(scanned) channel.
➥While pushing [H/L], push for 3 sec. to clear or set all TAG
channels.
oCHANNEL/DUALWATCH/TRI-WATCH KEY
[CH/WX•DW ]
➥Push to select and toggle the regular channels and
weather channels.
➥While pushing [H/L], push to select one of three channel
groups in sequence.
•U.S.A., International and Canadian channels are available.
➥Push for 1 sec. to start Dualwatch or Tri-watch.
➥Push to stop Dualwatch or Tri-watch when either is acti-
vated.
➥Move the cursor backward while in the channel comment
programming condition.
!0 CHANNEL 16/CALL CHANNEL KEY [16•9]
➥Push to select Channel 16.
➥Push for 1 sec. to select call channel.
•“CALL” appears when call channel is selected.
➥Push for 3 sec. to enter call channel programming condi-
tion when call channel is selected.
➥While pushing [H/L], push to enter the channel comment
programming condition.
➥While turning power ON, push to enter Set mode.
➥Advance the cursor while in channel comment program-
ming condition.
!1 VOLUME/SQUELCH•MONITOR/LOCK KEY
[
VOL/SQL• MONI
]
➥Push to select the volume, channel or squelch setting con-
dition.
➥After pushing this key, rotate [SELECTOR] to set the
audio level, channel selection or squelch level.
➥Push for 1 sec. to turn the monitor function ON.
➥While pushing [H/L], push this to toggle the (microphone)
Key Lock function ON or OFF.
•“ ” appears while (microphone) Key Lock function is in use.
•[PWR] ([CLR]/[MENU]), [PTT], [VOL/SQL],[H/L] and [DIS-
TRESS] still function when the (microphone) Key Lock func-
tion is turned ON.
!2 ATTENUATOR/INTERCOM/SCRAMBLER KEY
[LO/DX•IC ]
➥Push to toggle the Attenuator function ON or OFF.
•“
LLOOCC” appears when the Attenuator function is turned ON.
➥Push for 1 sec. to activate the Intercom function.
➥Calls the transceiver when pushed and held while in In-
tercom mode.
➥While pushing [H/L], activates an optional Voice scram-
bler function when it’s installed into the transceiver.
•“SSCCRRAAMM” appears when the Voice scrambler function is
turned ON.
•Voice scrambler function is available depending on the
transceiver or transceiver’s version.
•The optional Voice scrambler function cannot be used on
Channel 16 and 70.
!3 HAILER/RX SPEAKER KEY [HAIL•RX ]
➥Push to turn the hailer mode ON or OFF.
➥Push for 1 sec. to turn the RX Speaker mode ON or OFF.
➥While pushing [H/L], push to turn the automatic foghorn
function ON or OFF.
SCR
é
L
U/I/C
L
é
L
Top keys
Back side
o
i
u
y
!0
!1 !2 !3
w
q
r
t
e
Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Rus-
sia and/or other countries. COMMANDMIC III is a trademark of Icom Incorporated (Japan) in the United states.
cPanel description
2
qPush [PWR] to turn power ON.
wSet the audio and squelch levels.
➥Push
[VOL/SQL•MONI ] for 1 sec. to activate the moni-
tor function.
➥Rotate [SELECTOR
VOL
]to adjust the audio output level.
➥Push
[VOL/SQL•MONI ]
to cancel the monitor function
.
➥Push
[VOL/SQL•MONI ]
several times, then rotate [SE-
LECTOR
SQL
]to adjust the squelch level.
eWhile pushing [H/L], push [CH/WX•DW ] to change the
channel group, if desired.
r
Push [CH/WX•DW ] once, then rotate [SELECTOR
CH
]
to select the desired channel.
•When receiving a signal, “BBUUSSYY” appears and audio is emit-
ted from the speaker.
•Further adjustment of the audio level may be necessary.
tPush [LO/DX•IC ] to turn the Attenuator function ON or
OFF, if necessary.
•“
LLOOCC” appears when the Attenuator function is in use.
yPush [H/L] to select the output power, if necessary.
•“
11WW” appears when low power is selected.
•Choose low power for short range communications, choose
high power for longer distance communications.
•Some channels are for low power only.
uPush and hold [PTT] to transmit, then speak into the micro-
phone.
•“
TTXX” appears.
•Channel 70 cannot be used for transmission other than DSC.
Simplex channels, 3, 21, 23, 61, 64, 81, 82 and 83 CAN-
NOT be lawfully used by the general public in U.S.A. wa-
ters.
iRelease [PTT] to receive.
IMPORTANT: To maximize the readability of your transmit-
ted signal (voice), pause a few sec. after pushing [PTT],
hold the microphone 2 to 4 inches (5 to 10 cm) from your
mouth and speak at a normal voice level.
SCR
U/I/C
U/I/C
L
L
L
The HM-162 has a selector dial, which works various functions.
➥Each pushing
[VOL/SQL] changes [SELECTOR]’s action.
• Selector status indicator shows “[[VVOOLL]],” “[[SSQQLL]]” or
“[[CCHH]]” when [SELECTOR] functions as an audio volume,
squelch controller or channel selector, respectively.
➥Pushing
[CH/WX] changes [SELECTOR]’s action to channel
selector.
• “[[CCHH]]” appears.
➥Pushing
[ENT] or [CLR] returns [SELECTOR]’s action to the
audio volume when
“[[SSQQLL]]” or “[[CCHH]]” is indicated on the
display
.
• Even If [ENT] or [CLR] hasn’t been pushed, [SELECTOR]’s
action returns to the audio volume automatically after 5 sec. of
inactivity.
After these instructions describe [SELECTOR] as follow:
[SELECTOR
VOL
]: Functions as the audio volume.
[SELECTOR
SQL
]: Functions as the squelch controller.
[SELECTOR
CH
]: Functions as the channel selector.
[SELECTOR] : Functions as the any other selector or
controller.
vSelector’s action
bChannel selection nReceiving and transmitting
mMonitor function
DDChannel 16
qPush [16•9] to select Channel 16.
wPush [CH/WX] to return to the
condition before selecting Chan-
nel 16, (or rotate [SELECTOR
CH
]to select an other channel.
DDCall channel
qPush [16•9] for 1 sec. to select
call channel.
wPush [CH/WX] to return to the
condition before selecting call
channel, (or rotate [SELECTOR
CH
]to select an other channel.
DDWeather channels
qPush [CH/WX] once or twice to
select the weather channel group.
wRotate [SELECTOR
CH
]to select
a weather channel.
ePush [CH/WX] once or twice to
return to the condition before se-
lecting the weather channel
group.
DDU.S.A., International and Canadian channels
qPush [CH/WX•DW ] to select a regular channel.
•Push [CH/WX•DW ] again, if a weather channel appears.
wWhile pushing [H/L], push [CH/WX•DW ] to select a
channel group.
•U.S.A., International and Canadian channels can be selected
in sequence.
ePush [CH/WX•DW ] then rotate [SELECTOR
CH
]to se-
lect a channel.
•“
DDUUPP” appears for duplex channels.
•“ ” appears when a simplex channel is selected.
BUSY
-25W
25W
---
---
CAN
CAN
---CALL
---CALL
LOCAL--DUP
LOCAL--DUP
SCRAM
SCRAM
--TAG
--TAG
NORMAL-SCAN
NORMAL-SCAN
-34"34.206N
34"34.206N
123"23.236W
123"23.236W
--
--
UTC
UTC
-10:10
10:10
---
---
CCG
CCG
[VOL]
[VOL]
BUSY
-25W
25W
---
---
INT
INT
---CALL
---CALL
LOCAL--
LOCAL--
DUP
DUP
SCRAM
SCRAM
--TAG
--TAG
NORMAL-SCAN
NORMAL-SCAN
-34"34.206N
34"34.206N
123"23.236W
123"23.236W
--
--
UTC
UTC
-10:10
10:10
-TELEPHONE
TELEPHONE
[VOL]
[VOL]
BUSY
-25W
25W
---
---
USA
USA
---CALL
---CALL
LOCAL--DUP
LOCAL--DUP
SCRAM
SCRAM
--
--
TAG
TAG
NORMAL-SCAN
NORMAL-SCAN
-34"34.206N
34"34.206N
123"23.236W
123"23.236W
--
--
UTC
UTC
-10:10
10:10
---
---
CCG
CCG
[VOL]
[VOL]
U.S.A. channels
Canadian channels International channels
U/I/C
U/I/C
U/I/C
U/I/C
BUSY-25W----25W---WXWX---CALL---CALL
LOCAL--DUPLOCAL--DUP
SCRAMSCRAM--TAG--TAG
NORMAL-SCANNORMAL-SCAN
-34"34.206N34"34.206N
123"23.236W123"23.236W
----UTCUTC-10:10162.550MHz10:10162.550MHz
[CH[CH-]
Push
CH/WX
BUSY-25W25W------INTINT---CALL---CALL
LOCAL--DUPLOCAL--DUP
SCRAMSCRAM----TAGTAG
NORMAL-SCANNORMAL-SCAN
-34"34.206N34"34.206N
123"23.236W123"23.236W
----UTCUTC-10:1010:10-CALLINGCALLING
[CH[CH-]
for 1 sec.
916
Push
BUSY-25W25W------INTINT---CALL---CALL
LOCAL--DUPLOCAL--DUP
SCRAMSCRAM----TAGTAG
NORMAL-SCANNORMAL-SCAN
-34"34.206N34"34.206N
123"23.236W123"23.236W
----UTCUTC-10:1010:10- - CALLINGCALLING
[CH[CH-]
916
Push
The monitor function releases the noise squelch mute of the
microphone only. (An independent noise squelch system is
employed.)
➥Push
[VOL/SQL•MONI ]
for
1sec. to activate the Monitor
function.
•“
BBUUSSYY” blinks and audio is emit-
ted.
•
[VOL/SQL•MONI ] (or [ENT],
[CLR])
cancels the Monitor func-
tion
.
L
L
BUSYBUSY-25W25W------INTINT---CALL---CALL
LOCAL--DUPLOCAL--DUP
SCRAMSCRAM--TAG--TAG
NORMAL-SCANNORMAL-SCAN
-34"34.206N34"34.206N
123"23.236W123"23.236W
----UTCUTC-10:10COMMERCIAL10:10COMMERCIAL
[VOL][VOL]
Blinks
3
Produktspecifikationer
| Varumärke: | Icom |
| Kategori: | Ljud/videomottagare |
| Modell: | HM-162B SW |
Behöver du hjälp?
Om du behöver hjälp med Icom HM-162B SW ställ en fråga nedan och andra användare kommer att svara dig
Ljud/videomottagare Icom Manualer
14 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024
Ljud/videomottagare Manualer
- Ljud/videomottagare JVC
- Ljud/videomottagare Kenwood
- Ljud/videomottagare Onkyo
- Ljud/videomottagare Pioneer
- Ljud/videomottagare Yamaha
- Ljud/videomottagare Aiwa
- Ljud/videomottagare Harman Kardon
- Ljud/videomottagare Marantz
- Ljud/videomottagare Sherwood
- Ljud/videomottagare Eltax
- Ljud/videomottagare Konig Electronic
- Ljud/videomottagare Focusrit
Nyaste Ljud/videomottagare Manualer
24 Oktober 2024
24 Oktober 2024
23 Oktober 2024
20 Oktober 2024
20 Oktober 2024
18 Oktober 2024
14 September 2024
14 September 2024
14 September 2024
14 September 2024