IFi Audio iDSD Diablo 2 Bruksanvisning

IFi Audio Inte kategoriserad iDSD Diablo 2

Läs nedan 📖 manual på svenska för IFi Audio iDSD Diablo 2 (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/6

Thank you for purchasing the Diablo 2 from the Diablo series. iDSD Diablo 2The is a balanced USB and Bluetooth Ultra-Res

portable DAC + headphone amplifier

1. UnBalanced 6.35mm output

Connection for 6.35 single ended headphones . Please use 3.5 to 6.35 mm adaptor for 3.5 single ended headphones.

Tip: With a new pair of IEMs/Headphones, ALWAYS start with the volume no higher than 9 o' clock and with the Power Mode (item 4) set to 'Normal'.

2. Balanced 4.4mm and xMEMS analogue output

Connect balanced 4.4mm headphones. See the next section for instructions on using the xMEMS headset.

Tip: As iDSD Diablo 2 is balanced, we recommend the 4.4mm output.

3. xMEMS Mode ON/OFF

This mode is specifically designed for xMEMS headphones. To use xMEMS headphones, please enable xMEMS mode.

Tip: xMEMS transducers are a piezoelectric technology that has specific drive requirements, and can only be used when xMEMS mode is on.

Warning: With xMEMS mode on, please connect xMEMS IEMs to the balanced 4.4mm headphone output only (item 2). It is not recommended to connect other types of headphones while xMEMS mode is on. To

connect those, please turn off the xMEMS mode before connecting.

4. Power Mode

There are 3 different types of power output levels to drive different headphones from the ultra-sensitive in-ear monitors to the most

demanding over-ear headphones .

General mode

Approximate listening time (in Battery mode with typical headphones):

Normal for high-sensitivity IEMs, up to a maximum of 12 hours

Turbo for medium-sensitivity headphones, up to a maximum of 9 hours

Nitro for the most demanding headphones, up to a maximum 6 hours

xMEMS mode

Normal DC bias level is 10V, up to a maximum of 8 hours

Turbo DC bias level is 12V, up to a maximum of 7 hours

Nitro DC bias level is 14V, up to a maximum 6 hours

ii D

DD S

SS D D

D D

D DD D i

ii a

aa b

bb l

ll o 2

o 2

o 2o 2

Off

MO DEBAL

Turbo

Normal

Nitro

Off On

1 4 6 72

3 5

Of f

OFF

5. INPUT Mode/Audio Format (kHz) /Bluetooth Format LED

INPUT LED

LED Mode

White (flashing) Wired (USB or S/PDIF or 4.4mm)

Blue (flashing) Wireless Bluetooth (Awaiting connection)

Blue/Red (flashing) Wireless Bluetooth (Pairing)

Audio Format (kHz) LED

The LED colour scheme indicates the audio format and sampling frequency received by the iDSD Diablo 2 from the music source.

LED Format (kHz)

Yellow PCM 48/44.1kHz

White PCM 768/705.6/384/352.8/192/176.4/96/88.2kHz

Cyan DSD 128/64

Red DSD 512/256

Green MQA

Blue MQA Studio

Magenta Original Sample Rate*

*MQB

Attention: Installing GTO enabled firmware may result in the LED's on this device no longer changing in accordance with the above table

Bluetooth Format LED

The colors shown on the LEDs are based on the Bluetooth audio format received by the iDSD Diablo 2.

LED Format

Off SBC

Yellow AAC

Blue aptX

Magenta aptX HD

Green aptX Adaptive

White AaptX Lossless

Red HWA/LHDC

Cyan LDAC

6. Volume lock

Used to lock the volume knob in position. This prevents it from turning if touched accidentally, resulting in a sudden increase or

decrease in volume. It also prevents accidentally powering the iDSD Diablo 2 on.

7. ON/OFF and Analogue Volume Control

The analogue volume control in iDSD Diablo 2 is sonically superior to any digital volume control.

Warning: Due to the high power of iDSD Diablo 2, always start off at a low volume level so that there is no risk of damage to your headphones or your hearing. iFi audio is not responsible for any hearing or

equipment damage from misuse.

Power ON. Power OFF.

The iDSD Diablo 2 is equipped with a memory function, after powering on, it will automatically restore the last mode used. If the last

mode used when powering off was wireless Bluetooth mode, after powering on, the iDSD Diablo 2 will firstly enter into the Waiting for

Connection mode (item 5, INPUT: blue light blinking), which is the mode in which it automatically searches for the pairing device from

15 seconds ago; if it does not find the stored pairing device is not found, it will automatically enter the waiting pairing mode (item 5,

INPUT: blue/red light blinking alternately).

Tip: iDSD Diablo 2 will continue to use battery power even if the USB cable is connected afterwards.

Tip: For connection to Apple devices, an Apple Lightning to a USB Camera Adapter is required. For connection to Android devices, a USB-C to USB-C cable and appropriate OS support are required.

For more information, please refer to www.ifi-audio.com.

8. iEMatch switch

iEMatch reduces the output level, so that even the most sensitive In-Ear-Monitors (IEMs) can be matched to the iDSD Diablo 2.

iEMatch can increase the dynamic range of sensitive IEMs by reducing background amplifier hiss.

= 4.4mm headphones

= off

= 6.35mm headphone

Tip: The iDSD Diablo 2 or the headphone will not be damaged if the iEMatch switch is adjusted incorrectly, but the attenuation level will not be correct.