Intermatic ET8015C Bruksanvisning

Intermatic Inte kategoriserad ET8015C

Läs nedan 📖 manual på svenska för Intermatic ET8015C (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Electronic Astronomic

7-Day Time Switch

Time Switch

• Input Voltage: 120/208/240/277 VAC, 60 Hz

• Power Consumption: 6.0 W Max.

• Contact Conguration: SPST (ET8015C), DPST (ET8215C), and

SPDT (ET8115C). See wiring diagrams on next page.

Switch Ratings—ET8015C, ET8215C (per pole)

• 30 A Inductive/Resistive, 120/240 VAC, 60 Hz

• 20 A Ballast, 120-277 VAC, 60 Hz

• 20 A Resistive, 28 VDC

• 5 A Tungsten: 120/240 VAC, 60 Hz

• 1 HP, 120 VAC, 60 Hz

• 2 HP, 240 VAC, 60 Hz

Switch Ratings—ET8115C (NO/NC) Normally Open/Normally Closed Contact

• 20 A/10 A Inductive/Resistive, 120/208/240 VAC, 60 Hz

• 20 A/3 A Ballast, 120-277 VAC, 60 Hz

• 5 A Tungsten: 120/240 VAC, 60 Hz

• 1 HP / ¼ HP, 120 VAC, 60 Hz

• 2 HP / ½ HP, 240 VAC, 60 Hz

Set Points (Events)—Each load output of the Time Switch can support up

to 14 timed ON and 14 timed OFF events per day as well as Astro ON

and Astro OFF events.

Installation and User Instructions

MODEL ET8000 Series

The Intermatic ET8000 Series Electronic Astronomic 7-Day Time

Switch automatically switches loads to a preset weekly schedule with

to-the-minute accuracy.

• The astronomic feature provides an automatically adjusted sunset

ON and sunrise OFF to eliminate the need for separate photo control

devices.

• The independent 7-day programming provides complete exibility for

applications where load switching differs each day of the week.

• Astronomic programming can be combined with independent

programming to provide a sunset ON and timed OFF program.

Use the ET8000 series as an ON/OFF timer in applications requiring

7-day astronomic load control such as lighting, air conditioning systems,

pumps, etc. Each load output of the Time Switch can support up to 14

timed ON and 14 timed OFF events per day as well as Astro ON and Astro

OFF events. The program can be overridden by pushing the ON/OFF load

override button(s).

The ET8000 Series Time Switch is designed to directly switch tungsten

or ballast loads up to its rating, and inductive or resistive loads up to

30A at 120, 208, 240, or 277 VAC.

Speciﬁcations

With Battery

Carryover

Description

Front View Rear View

WARNING Risk of Fire or Electric Shock

• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.

• Installation and/or wiring must be in accordance with national and local electrical code

requirements.

• For outdoor locations or wet locations (rain-tight), conduit hubs that comply with requirements of

the UL514B (standard for ﬁtting conduit and outlet boxes) are to be used.

• This enclosure does not provide grounding between conduit connections. When metallic conduit

is used, you must also install grounding type bushings and jumper wire.

• For plastic enclosures, bonding between conduit connections is not automatic and must be

provided as part of the installation.

• Use #18 - #10 AWG wires, rated at least 75°C - COPPER conductors ONLY.

• If the power disconnect point is out of sight, lock it in the OFF position and tag it to prevent

unexpected application power.

• Make sure there is no wire insulation under the terminal plate on the time switch connector.

Firmly tighten terminal screws.

• Do not remove insulator that is covering terminals.

• KEEP DOOR CLOSED AT ALL TIMES when not servicing.

NOTICE

• Do NOT touch circuit board components, contact can create a static discharge, which can

damage the microprocessor.

Installation Instructions

Slide down

to remove

battery case

Snap out catch

Tilt top forward

2. Set voltage selector for desired input voltage. The timer is

shipped with voltage set for 120 VAC. To

operate at 208, 240 or 277 VAC, move the

selector switch to the desired setting as

marked on the circuit board. See location in A

Rear View above and detail at the right.

3. The timer is shipped with DST (Daylight Saving

Time) enabled. To disable DST, insert a jumper

at location marked DST. See location in BRear

View above and detail at the right.

4. ET8215C ONLY—Decide whether you want to

control multiple loads simultaneously (SIM),

independently (IND), or with a 2-second pulse

(PUL) (e.g., for use with mechanically held

contactors or bell ringing applications), and

make sure the jumper is positioned accordingly.

See location in above and detail at the right. BRear View

(The unit is shipped with the loads set for IND.)

1. Remove the mecha-

nism from the case by

depressing the catch

at the top of the case

and pulling out, as

shown.

Battery-Powered Clock Operation—3 years minimum (uses 2 AAA industrial

grade alkaline batteries, supplied)

Minimum ON or OFF time—1 minute

Maximum ON or OFF time—6 days, 23 hours, 59 minutes

Shipping Weight—2.5 lb. (1.1 kg)

Enclosures—Three enclosure options are available.

• ET8xx5C – TYPE 1 indoor metal enclosure

• ET8xx5CR – TYPE 3R indoor/outdoor lockable metal enclosure

• ET8xx5CPD82 – TYPE 3R indoor/outdoor lockable impact resistant

polycarbonate enclosure with clear cover

Knockouts—Combination 1/2-3/4 inch size, 1 on back and each side,

2 on bottom

Wire Size—AWG #18 through #10

Knockouts

Mounting holes

Neutral

120VAC

Input

Hot

2 3 4

Timer Power

Load

Install jumper

only if timer input

and load voltage

are the same

ET8015 conﬁgured for SPST, 120 VAC load

L2/N

120/208/240/277

VAC Input

Line 1

2 3 4 5 6

Load

1Load

Timer Power

Install jumper only if timer input

and load voltage are the same

ET8115 conﬁgured for SPDT load switching

Line 2

240VAC Input

Line 1

2 3 4 5 6

Line 1

Line 2

Install jumper only if timer input

and load voltage are the same

Timer Power

Load

ET8215 conﬁgured for 240 VAC DPST load

with jumper set to SIM

L2/N

120/208/240/277

VAC Input

Line 1

23456

Install jumper only if timer input

and load voltage are the same OFF

Timer Power

ET8215 conﬁgured for pulse SPST load

with jumper set to PUL

L2/N

120/208/240/277

VAC Input

Line 1

2 3 4 5 6

Load

Timer Power

Load

ET8215 conﬁgured for 2 SPST loads

with jumper set to IND

L2/N

120/208/240/277

VAC Input

Line 1

2 3 4 5 6

Load

Timer Power

Load

ET8215 conﬁgured for DPST loads

with jumper set to SIM

Mounting

Holes

Knockouts

Mounting

Hole

Programming Overview

By pressing the button, the Time Switch will cycle through the MODE

menus necessary for programming the current time, date, astro zone,

astro events, and timed events.

The basic procedure is to use the button to move from one MODE

menu to the next (e.g., DATE, TIME, etc.), the or buttons for the + –

rst part of a setting (e.g., MONTH), the button to move to the ENTER

next part of the setting (e.g., YEAR), then to exit and move to the MODE

next menu. To skip a menu, press to move ahead.MODE

If you make a mistake, press the button repeatedly to cycle MODE

back around to the error, then make the correct entry.

NOTE: DATE and TIME must be set before you can access any other

programming menus.

Setting Date

1. Press the button repeatedly until the words SET and DATE MODE

appear in the upper area of the display.

Setting Time

1. If necessary, press the button repeatedly until the words MODE

SET and CLOCK appear in the upper area of the display.

2. Press the or buttons to enter the current time.+ –

NOTE: To go from AM to PM, keep pressing the + or – buttons to

cycle through the day. You can hold the buttons down for +or –

3 seconds to make the time scroll quickly.

3. Press the button to exit and advance to setting Astro Zone.MODE

2. Press the or buttons to enter the current Month.+ –

3. Press the ENTER button when the Month is correct to save the

setting. The screen advances to current Date.

4. Again press the + or – buttons to enter the current Date, followed

by the button.ENTER

5. Repeat to set the correct Year.

6. Press the button to exit and advance to setting the time.MODE

Wiring Diagrams

6. Replace the mechanism in the enclosure.

7. Lift the left side of the plastic insulator off the retaining post and

pivot it up and away to expose the terminal strip.

8. Strip the supply and load wires to 1/2”. Use #18 - #10

AWG wires, rated at least 75°C - COPPER conductors ONLY

5. Mount the enclosure in the desired location using the 3

mounting holes provided.

9. Insert the wire ends under the proper terminal plates (see wiring

diagrams elsewhere on this page) and tighten the screws rmly.

10. Connect ground wire to grounding terminal at bottom of enclosure.

11. Replace the plastic insulator on the retaining post.

12. Remove the battery case by sliding it down as shown by the

arrows, then install 2 AAA alkaline batteries. Make sure the

batteries are pointing in the direction shown.

13. Verify that the display is to make sure the batteries are OK.ON

If the display shows scrambled information, press the RESET

button to clear it up.

14. Apply power to the Time Switch.

The Time Switch is now ready for programming.

Position at eye level if possible, providing space to the left of

the enclosure for the cover to swing open fully, as shown.

IMPORTANT: ENTER Press and hold the button, then press the

RESET button. The screen will ash 12:00 AM and MON, and timer

status is Manual Mode.

NOTE: You must reset the time switch using this procedure

whenever you change the jumpers.

An ASTRO event will let you set Sunset ON and Sunup OFF events.

1. If necessary, press the button repeatedly until the words MODE

SET, ASTRO, and ON/OFF EVENTS appear in the upper area of

the display.

2. Press the button if necessary to display ON @.ENTER

3. Make sure you know which days you want the Event to be active.

- If you want the Event to occur every day of the week, press the

DAY button to display SUNSET and all days.

- If you want the Event to occur for a different combination of

days, press the button again as necessary to cycle through DAY

the days or combination of days you want.

Setting SUNSET ON/SUNUP OFF Events

Setting Astro Zone

Astro Zone is how far north or south the location is, to adjust for

differences in sunrise and sunset for better accuracy in turning lights

on and off at dawn and dusk.

1. If necessary, press the

MODE button repeatedly

until the words SET and

ASTRO ZONE appear in

the upper area of the

display.

2. Press the or + – buttons

to display the Zone that

includes the location.

Use the map at the right

as a reference.

3. Press the button to exit and advance to setting exact Astro MODE

times.

South

North

Center

North

Center

South

Setting Exact Astro Times

When you choose an Astro Zone, the Time Switch uses an approximate

time for sunup and sunset, adjusting automatically as the seasons

change (earlier sunset in winter, etc.) You can set sunup and exact

sunset times, which are available in the newspaper or on the Internet.

For multi-circuit time switch ET8215C, you can set multiple sunup and

sunset times—useful, for example, in environments involving lighting

with different warm-up times.

1. If necessary, press the MODE button repeatedly until the words SET

and SUNUP appear in the upper area of the display. The display

also shows the default sunup time for the date and zone.

2. Press the or buttons to adjust the sunup time. + – You can offset

the time up to 120 minutes in either direction.

3. Press the button:MODE

- If a time switch, SUNUP and LOAD 2 appear on multi-circuit

the display.

a. Press the or buttons to set the exact Sunup time for + –

Load 2.

b. Press the button to advance to Sunset for Load 1. MODE

- If a single-circuit time switch,

The words SET and SUNSET appear on the display, along with the

default sunset time for the date and zone.

4. Press the or buttons to adjust the sunset time. + – You can offset

the time up to 2 hours (120 minutes) in either direction.

5. Press the button:MODE

- If a time switch, SUNSET and LOAD 2 appear on multi-circuit

the display.

a. Press the or buttons to set the exact Sunset time for + –

Load 2.

b. Press the button. MODE

- If a single-circuit time switch,

The time switch exits and advances to setting events.

NOTE: To remove an individual day, press the button DAY

until the day is blinking, then press the button.–

4. When you have set the event correctly, press the button ENTER to

set the next Astro event, which is for Sunup OFF. The words SET,

ASTRO, ON/OFF EVENTS, and OFF @ display.

5. Repeat from Step 3 above to set the event for OFF instead of ON.

6. Press the button to exit and advance to setting xed time MODE

events.

An ASTRO event will let you set Sunset ON and Sunup OFF events.

When the circuits of multi-circuit time switch ET8215C set to be

independent of each other, you can set sunup and sunset times for

either or both circuits.

1. Verify that the two circuits are independent. Refer to Step 4 in

Installation Instructions on page 1.

2. If necessary, press the button repeatedly until the words SET, MODE

ASTRO, ON/OFF EVENTS, and LOAD 1 appear in the display.

3. Press the button if necessary to display ON @.ENTER

4. Make sure you know which days you want the Sunset ON event

to be active.

- If you want the Event to occur every day of the week, press the

DAY button to display SUNSET and all days.

- If you want the Event to occur for a different combination of

days, press the button again as necessary to cycle through DAY

the days or combination of days you want.

NOTE: To remove an individual day, press the button DAY

until the day is blinking, then press the button.–

5. When you have set the event correctly, press the button to ENTER set

the next Astro event, which is Sunset ON for Load 2. The words SET,

ASTRO, ON/OFF EVENTS, LOAD 2, and ON @ appear in the display.

6. Repeat from Step 4 above to set the event for ON.

7. Press the button to set Sunup OFF for Load 1. The words ENTER

SET, ASTRO, ON/OFF EVENTS, LOAD 1 and OFF @ appear in

the display.

8. Repeat from Step 4 above to set the Event for OFF instead of ON.

9. Press the button to set Sunrise OFF for Load 2. The words SET, ENTER

ASTRO, ON/OFF EVENTS, LOAD 2, and OFF @ display.

10. Repeat from Step 4 above to set the event for OFF instead of ON.

11. Press the MODE button to exit and advance to setting xed time

events.

Setting SUNSET ON/SUNUP OFF Events

on Multi-Circuit Time Switches (ET8215C)

1. If necessary, press the button repeatedly until the words MODE

SET, FIXED, ON/OFF EVENT and EVENT 01 appear on the

display.

2. If necessary, press the button to display ON @ or OFF @ ENTER

(depending on what you want to set).

3. Press the button to display 12:00 am and all days of the DAY

week.

4. Press the + or buttons to enter the time you want to set.–

NOTE: To go from AM to PM, keep pressing the + or – buttons

to cycle through the day. You can hold the +or – buttons down

for 3 seconds to make the time scroll quickly.

5. If you want the Event to occur for a combination of days rather

than every day (e.g., weekends only, weekdays only, or individual

days), press the DAY button again as necessary to cycle through

the individual days or combination of days you want.

NOTE: To choose a combination not shown during cycling

(e.g., Tuesday and Thursday), you must create an individual

event for each of the days you want.

Setting Fixed Timed Events

Produktspecifikationer

Varumärke:	Intermatic
Kategori:	Inte kategoriserad
Modell:	ET8015C

Behöver du hjälp?

Om du behöver hjälp med Intermatic ET8015C ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Intermatic Manualer

Intermatic T101PC Bruksanvisning

26 September 2024

Intermatic T103 Bruksanvisning

26 September 2024

Intermatic T103PC Bruksanvisning

26 September 2024

Intermatic T104PC Bruksanvisning

26 September 2024

Intermatic T104 Bruksanvisning

18 September 2024

Intermatic ET8015C Bruksanvisning

16 September 2024

Intermatic ET8215C Bruksanvisning

16 September 2024

Intermatic Ascend STW700W Bruksanvisning

16 September 2024

Intermatic WP3100C Bruksanvisning

16 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024