JennAir WRF954CIHZ Bruksanvisning

JennAir kylskåp WRF954CIHZ

Läs nedan 📖 manual på svenska för JennAir WRF954CIHZ (64 sidor) i kategorin kylskåp. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/64

W11509210C

FRENCH DOOR BOTTOM MOUNT OWNER'S

MANUAL

MANUEL D’UTILISATION DE RÉFRIGÉRATEUR À

PORTE À DOUBLE BATTANT ET CONGÉLATEUR EN

BAS

Table of Contents/Table des matières

REFRIGERATOR SAFETY.................................................2

Refrigerator Safety .........................................................2

REFRIGERATOR CARE .................................................... 3

Cleaning ............................... .............. ......................... 3

Changing the Light Bulb ..................................................4

Refrigerator Shelves.......................................................5

Opening and Closing Doors ............................................. 6

Vacation and Moving Care ...............................................6

INSTALLATION INSTRUCTIONS ................................... ..... 7

Unpack the Refrigerator ......... ............. .............. .............. 7

Location Requirements ................. ............. .............. ....... 8

Electrical Requirements ..................................................8

Water Supply Requirements.............................................8

Connect the Water Supply ..................... .............. ............ 9

Complete the Installation ............................................... 10

Install Air Filter (on some models).................................... 10

Install Produce Preserver (on some models) ...................... 12

REFRIGERATOR FEATURES........................................... 13

Crisper Humidity Control (on some models) ....................... 13

Water and Ice Dispensers (on some models) ..................... 13

Ice Maker and Storage Bin ............................................. 14

Water Filtration System ................................................. 16

DOOR AND HANDLE INSTRUCTIONS .............................. 18

Door and Drawers .... ............................ .............. .......... 18

Remove and Replace Handles........................................ 18

Remove Refrigerator Doors and Hinges............................ 20

Reset Bottom Refrigerator Door Hinge ............................. 21

Replace Refrigerator Doors and Hinges ............................ 22

Remove and Replace Refrigerator Drawer ........................ 22

Door Closing and Alignment ........... ............. .............. ..... 24

PERFORMANCE DATA SHEET ........................................ 28

Performance Data Sheet ............................................... 28

SÉCURITÉ DU RÉFRIGÉRATEUR .................................... 30

Sécurité du réfrigérateur ................................................ 30

ENTRETIEN DU RÉFRIGÉRATEUR................................... 31

Nettoyage .................................................................. 31

Remplacer l’ampoule d’éclairage..................................... 33

Tablettes du réfrigérateur............................................... 33

Ouverture et fermeture des portes ................................... 35

Précautions à prendre avant les vacances ou le

déménagement ........................................................... 35

INSTRUCTIONS D’INSTALLATION ................................... 36

Déballage du réfrigérateur ............................................. 36

Exigences d’emplacement ............................................. 37

Spécifications électriques .............................................. 37

Spécifications de l’alimentation en eau ............................. 38

Raccordement à la canalisation d’eau .............................. 38

Terminer l’installation .................................................... 40

Installer le filtre à air (sur certains modèles) ....................... 40

Installation du conservateur de produits frais (sur certains

modèles).................................................................... 41

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR..................... 42

Commande d’humidité dans le bac à légumes (sur certains

modèles).................................................................... 42

Distributeur d’eau et de glaçons (sur certains modèles) ........ 43

Machine à glaçons et bac d’entreposage........................... 43

Système de filtration de l’eau .......................................... 45

INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE............ 47

Porte et tiroirs ............................................................. 47

Pour enlever et réinstaller les poignées............................. 48

Démontage des portes et charnières du réfrigérateur........... 49

Réinitialiser la charnière inférieure du réfrigérateur.............. 51

Réinstallation des portes et charnières ............................. 52

Retrait et réinstallation du tiroir de congélation ................... 52

Fermeture et alignement des portes................................. 54

FICHE DE DONNÉES DE PERFORMANCE ........................ 58

Fiche de données de performance................................... 58

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

DANGER You can be killed or seriously injured if you don't

immediately follow instructions.

WARNING You can be killed or seriously injured if you don’t follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,

including the following:

�Children should be supervised to ensure that they do not

play with the appliance.

�This appliance is not intended for use by persons (including

children) with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety.

�Do not use an extension cord.

�If power supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or a similarly qualified

person in order to avoid a hazard.

�Connect to potable water supply only.

�This appliance is intended to be used in household and

similar applications such as: staff kitchen areas in shops,

offices, and other working environments; farm houses and

by clients in hotels, motels, and other residential-type

environments; bed and breakfast-type environments; and

catering and similar non-retail applications.

�Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

�Do not use replacement parts that have not been

recommended by the manufacturer (e.g., parts made at

home using a 3D printer).

�Keep ventilation openings, in the appliance enclosure or in

the built-in structure, clear of obstruction.

�Do not use mechanical devices or other means to

accelerate the defrosting process, other than those

recommended by the manufacturer.

�Do not damage the refrigerant circuit.

�Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type

recommended by the manufacturer.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

WARNING: Risk of child entrapment. Before you throw

away your old refrigerator or freezer:

�Take off the doors.

�Leave the shelves in place so that children may not easily

climb inside.

WARNING

Suffocation Hazard

Remove doors or lid from your old appliance.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation

are not problems of the past. Junked or

abandoned freezers or refrigerators, are still

dangerous, even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator

or freezer, please follow these instructions to help

prevent accidents.

Important information to know about disposal

of refrigerants:

Dispose of refrigerator in accordance with Federal

and Local regulations. Refrigerants must be

evacuated by a licensed, EPA certified refrigerant

technician in accordance with established

procedures.

REFRIGERATOR CARE

Cleaning

WARNING

Explosion Hazard

Risk of Fire or Explosion.

Flammable Refrigerant Used.

Do Not Use Mechanical Devices to Defrost Refrigerator.

Do Not Puncture Refrigerant Tubing.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid odor

buildup. Wipe up spills immediately.

IMPORTANT:

�Because air circulates between all sections, any odors formed

in one section will transfer to the other. You must thoroughly

clean all sections to eliminate odors. To avoid odor transfer

and drying out of food, wrap or cover foods tightly.

�Do not use abrasive or harsh cleaners such as window sprays,

scouring cleansers, flammable fluids, muriatic acid, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on doors and cabinet, plastic

parts, interior and door liners or gaskets. Do not use paper

towels, scouring pads, or other harsh cleaning tools.

�For stainless steel models, stainless steel is corrosion

resistant and not corrosion-proof. To help avoid corrosion of

your stainless steel, keep your surfaces clean by using the

following cleaning instructions.

Cleaning the Touch Screen Display on the

Dispenser Panel (on some models):

1. Make sure the refrigerator is unplugged or the power is

disconnected before wiping the screen to avoid unintentionally

changing the settings.

2. Mix a solution of mild detergent in warm water. Dampen a soft,

lint-free cloth with the solution and gently wipe the screen.

NOTE: Do not spray or wipe liquids directly onto the screen or

over-saturate the cloth.

3. Plug in refrigerator or reconnect power.

Cleaning the Interior:

IMPORTANT: Refrigerator shelves with under-shelf, LED lighting

are not dishwasher safe.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Plug in refrigerator or reconnect power.

Cleaning the Exterior:

IMPORTANT: Damage to smooth finish due to improper use of

cleaning products or using non-recommended cleaning products

is not covered under the warranty. Sharp or blunt instruments will

mar the finish.

1. Unplug refrigerator or disconnect power.

2. Using a clean sponge or soft cloth and a mild detergent in

warm water, wash, rinse, and thoroughly dry stainless steel

and painted metal exteriors.

To keep your stainless steel refrigerator looking like new and

to remove minor scuffs or marks, it is suggested that you use

the manufacturer’s approved stainless steel cleaner and

polish. This cleaner is for stainless steel parts only. Refer to

the Quick Start Guide for ordering information.

NOTE : When cleaning stainless steel, always wipe in the

direction of the grain to avoid cross-grain scratching.

Do not allow the stainless steel cleaner and polish to come

into contact with any plastic parts such as the trim pieces,

dispenser covers, or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

3. Plug in refrigerator or reconnect power.

Style 1: Smooth Door/Painted Metal

DO USE DO NOT USE

� �Soft, clean cloth Abrasive cloths

�Paper towels or newsprint

�Steel-wool pads

�Warm, soapy water with a

mild detergent

�Abrasive powders or

liquids

�Window sprays

�Ammonia

�Acidic or vinegar-based

cleaners

�Oven cleaners

�Flammable fluids

NOTE: Paper towels scratch and may dull the clear coat of the

painted door. To avoid possible damage, use only soft, clean

cloths to polish and wipe the door.

Style 2: Stainless Steel

DO USE DO NOT USE

� �Soft, clean cloth Abrasive cloths

�Paper towels or newsprint

�Steel-wool pads

�Warm, soapy water with a

mild detergent

�Abrasive powders or

liquids

�Ammonia

�Citrus-based cleaners

�Acidic or vinegar-based

cleaners

�Oven cleaners

�For heavy soil, use only a

manufacturer’s approved

stainless steel cleaner and

polish

�Abrasive powders or

liquids

�Ammonia

�Citrus-based cleaners

�Acidic or vinegar-based

cleaners

�Oven cleaners

�Abrasive cloths

�Paper towels or newsprint

�Steel-wool pads

NOTES:

�If unintentional contact does occur, clean plastic part with a

sponge and mild detergent in warm water. Dry thoroughly with

a soft cloth.

�Avoid exposing stainless steel appliances to caustic or

corrosive elements such as high-salt, high-moisture, or high-

humidity environments. Damage due to exposure to these

elements is not covered under the warranty.

�Just because a cleaner is a liquid does not mean it is

nonabrasive. Many liquid cleansers formulated to be gentle on

tile and smooth surfaces still damage stainless steel.

�When cleaning stainless steel, always wipe in the direction of

the grain to avoid cross-grain scratching.

�Citric acid permanently discolors stainless steel. To avoid

damaging the finish of your stainless steel refrigerator:

Do not allow these substances to remain on the finish:

• Mustard

• Tomato juice

• Marinara sauce

• Citrus-based sauces

• Citrus-based products

Condenser Cleaning

WARNING

Explosion Hazard

Risk of Fire or Explosion due to Puncture of Refrigerant

Tubing;

Follow Handling Instructions Carefully.

Flammable Refrigerant Used.

There is no need for routine condenser cleaning in normal home

operating environments. If the environment is particularly greasy

or dusty or there is significant pet traffic in the home, the

condenser should be cleaned every 6 months to ensure maximum

efficiency.

1. Unplug refrigerator or disconnect power.

2. Remove the base grille.

3. Use a vacuum cleaner with a soft brush to clean the grille, the

open areas behind the grille, and the front surface area of the

condenser.

4. Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

NOTE: If you are unable to clean the condenser, please call for

service.

Changing the Light Bulb

IMPORTANT: The lights in both the refrigerator and freezer

compartments use LED technology that do not need to be

replaced. If the lights do not illuminate when the door or drawer is

opened, call for assistance or service. Refer to the Quick Start

Guide for contact information.

The lighting system in this appliance may consist of:

�Sealed LED modules

�LED Bulbs

�Incandescent Bulbs

�Or a combination of the above.

If an LED bulb does not illuminate when the refrigerator and/or

freezer door is opened, replace with like bulb following this

procedure:

1. Unplug refrigerator or disconnect power.

2. Remove the light shield (on some models).

�Remove the hardware holding the light shield in place.

�Top of the refrigerator compartment - Slide the light shield

toward the back of the compartment to release it from the

light assembly.

3. Not all appliance bulbs will fit your refrigerator. Replace the

burned-out bulb(s) with an appliance bulb of the same size,

shape and wattage. Order part number W10565137 (3.6 W).

NOTE: Some LED replacement bulbs are not recommended

for wet/damp environments. The refrigerator and freezer

compartments are considered to be wet/damp environments.

If using a brand of LED bulb other than the recommended

LED bulb, before installation, read and follow all instructions

on the LED packaging.

4. Replace the light shield (on some models) by inserting the

tabs on the shield into the liner holes on each side of the light

assembly. Slide the shield toward the front until it locks into

place.

NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking point.

5. Replace the hardware that holds the shield in place.

6. Plug in refrigerator or reconnect power.

If an incandescent bulb does not illuminate when the refrigerator

and/or freezer door is opened, replace with like bulb using the

same procedure outlined above. Replace burned-out bulb with

only incandescent bulb(s) of the same size, shape, and wattage

(maximum 40 W) designed for household appliances.

Freezer Compartment Light (on some models)

1. Unplug refrigerator or disconnect power.

2. Remove the light shield.

Top of the freezer compartment - Slide the light shield toward

the back of the compartment to release it from the light

assembly.

3. Replace the burned-out bulb with an appliance bulb(s) no

greater than 40 W.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power.

Refrigerator Shelves

Important information to know about glass shelves and

covers:

Do not clean glass shelves or covers with warm water when they

are cold. Shelves and covers may break if exposed to sudden

temperature changes or impact, such as bumping. Tempered

glass is designed to shatter into many small, pebble-size pieces.

This is normal. Glass shelves and covers are heavy. Use both

hands when removing them to avoid dropping.

The shelves in your refrigerator are adjustable to match your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy

Glass Shelves

To remove a shelf:

1. Remove items from the shelf.

2. Slide the shelf straight out to the stop.

3. Depending on your model, lift the back or front of the shelf

past the stop. Pull the shelf out the rest of the way.

To replace a shelf:

1. Slide the back of the shelf into the track in the wall of the

cabinet.

2. Guide the front of the shelf into the shelf track. Be sure to slide

the shelf in all the way.

Shelves with Shelf Frames

To remove and replace a shelf/shelf frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports.

3. Lower the front of the shelf and make sure that the shelf is in

position.

Shelves with Under-Shelf Lighting (on some

models)

By moving LED lighting to a new spot under the shelves, this

leading-edge technology improves interior refrigerator lighting and

aids in locating storage items.

�For models with the shelf frames, the hooks on the rear of the

shelf must be fully engaged in the shelf supports to maintain

proper electrical flow.

�No more than two shelves with under-shelf lighting may be

used in the refrigerator at one time.

Shelves with Shelf Mounts

Shelf height can be adjusted by changing the adjustable shelf

mounts between their vertical and horizontal positions.

1. Carefully lift the shelf off the shelf mounts and turn the flipper

to the desired orientation.

2. Repeat for remaining shelf mounts.

3. Apply pressure to the top of the shelf to ensure the shelf is

properly seated on the shelf mounts.

To remove and replace shelves:

1. Make sure adjustable shelf mounts are in the lower position

before removing shelves. Also doors will need to be open at a

90˚ angle. If open wider, it will make it harder to remove the

shelves.

2. Remove the middle shelf or top shelf by lifting it up and out of

the shelf supports. Then pull the shelf forward and tilt down to

a vertical position. Turn the shelf at an angle and pull out of

the refrigerator.

Infinity slide glass shelves should be pushed back in. When

tilted up, make sure glass does not slide to front.

NOTE: Remove middle shelf first before removing top shelf.

3. Remove the bottom shelf by lifting it up and out of the shelf

supports. Then pull the shelf forward and tilt up to a vertical

position. Turn the shelf at an angle and pull out of the

refrigerator.

4. Replace the middle and top shelves by putting the shelf in the

refrigerator at an angle with the shelf front down. Lift the front

of the shelf up and slide in until rear shelf drops into the shelf

supports. Lower the front of the shelf and make sure that the

shelf is in position.

5. Replace the bottom shelf by putting the shelf in the refrigerator

at an angle with the shelf up. Lift the front of the shelf down

and slide in until rear shelf drops into the shelf supports.

Lower the front of the shelf and make sure that the shelf is in

position.

Tuck/Slide Away Shelf (on some models)

Some shelves will tuck/slide away to create room for taller objects.

To retract and extend the front section of the shelf:

1. To retract the front-section of the shelf, slightly lift up on the

front edge and push the adjustable portion of the shelf back

toward the rear of the refrigerator.

2. Extend the front of the shelf by pulling the retracted portion of

the shelf outward until it is fully extended.

Foldaway Shelf (on some models)

To retract the fold away shelf:

Retract the fold away section of the shelf by holding the front of

the shelf with one hand and lifting up on the center front of the

shelf. Then push back and down on the shelf until it slides

beneath the back section of the shelf.

To replace the fold away shelf:

Replace the fold away section of the shelf by holding the front of

the shelf with one hand and pulling the center of the shelf until the

fold away section is returned to its full shelf position.

MicroEdge®® Glo Shelves (on some models)

The hooks on the rear of the shelf must be fully engaged in the

shelf supports to maintain proper electrical flow.

No more than two shelves with under-shelf lighting may be used in

the refrigerator at one time.

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together. On some

models, there is a, automatic closing mechanism so the door(s)

will not unintentionally be left open. If a door is open at a 40° or

smaller angle, the door will automatically, softly close.

IMPORTANT: If the doors do not automatically close at a 40° or

smaller angle, see “Bottom Door Hinge.”

There is a vertically-hinged seal on the left refrigerator door.

�When the left-hand door is opened, the hinged seal

automatically folds inward so that it is out of the way.

�When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

The refrigerator compartment door switch is located in the top left

and right hinge cover.

�The door switch uses magnet to sense door opening/closing.

�Ensure there are no magnet or electronic devices (Speaker,

CoolVox®, etc) within 3 inches of the hinge cap.

NOTE: The light and internal user interface (UI) will not turn on if

the door opening is not detected.

A. Hinged cover

Vacation and Moving Care

Vacation

If You Choose to Leave the Refrigerator On While You’re

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm

to Off (up) position or press the switch to Off.

4. Empty the ice bin.

Models with Vacation Mode Feature

�Turn on Vacation mode. See the “Quick Start Guide” for

details.

NOTE: Activating Vacation mode does not turn off the ice

maker.

If You Choose to Turn Off the Refrigerator Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

�Turn off the water supply to the ice maker at least one day

ahead of time.

�When the last load of ice drops, raise the wire shutoff arm

to the Off (up) position or press the switch to Off,

depending on your model.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See the “Quick Start

Guide.”

5. Clean refrigerator, wipe it, and dry well.

6. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

�Turn off the water supply to the ice maker at least one day

ahead of time.

�Disconnect the water line from the back of the refrigerator.

�When the last load of ice drops, raise the wire shutoff arm

to the Off (up) position or press the switch to Off,

depending on your model.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See the “Quick Start

Guide.”

5. Unplug refrigerator

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily or raise the leveling screws so they don’t

scrape the floor. See “Adjust the Door(s)” or “Door Closing and

Door Alignment.”

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the “Installation Instructions” section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall

appliance.

Failure to do so can result in back or other injury.

Refrigerator Delivery

�A minimum door opening of 33" (838 mm) is required. If door

opening is 36" (914 mm) or less, then removal of doors,

drawer, and hinges is required.

�Cart the refrigerator from the side for all door openings.

Remove the Packaging

�Remove tape and glue residue from surfaces before turning on

the refrigerator. Rub a small amount of liquid dish soap over

the adhesive with your fingers. Wipe with warm water and dry.

�Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see “Refrigerator Safety.”

�Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or

hardboard to avoid floor damage. Always pull the refrigerator

straight out when moving it. Do not wiggle or “walk” the

refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions in

“Refrigerator Care.”

Important information to know about glass shelves and

covers:

Do not clean glass shelves or covers with warm water when they

are cold. Shelves and covers may break if exposed to sudden

temperature changes or impact, such as bumping. Tempered

glass is designed to shatter into many small, pebble-size pieces.

This is normal. Glass shelves and covers are heavy. Use both

hands when removing them to avoid dropping

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline,

away from appliance.

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

IMPORTANT: This appliance is intended to be used indoor for

household and similar applications such as:

�Farm houses and by clients in hotels, motels and other

residential type environments.

�Bed and breakfast type environments.

�Catering and similar non-retail applications.

NOTE: If the manufacturer wants to limit the use of the appliance

to less than the above, this has to be clearly stated in the

instructions.

To ensure proper ventilation for your refrigerator, allow for 3/16"

(0.48 cm) of space on each side and 1/4ʺ (0.64) at the top. Allow

for 1" (2.54 cm) of space behind the refrigerator. If your

refrigerator has an ice maker, allow extra space at the back for the

water line connections. When installing your refrigerator next to a

fixed wall, leave a 14" (35.56 cm) minimum space between the

refrigerator and wall to allow for the door to swing open.

NOTE: This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature range

for optimum performance, which reduces electricity usage and

provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified person.

Do not use a cord that shows cracks or abrasion damage along its

length or at either the plug or connector end.

Recommended Grounding Method

A 115 V, 60 Hz, AC-only 15 A or 20 A fused, grounded electrical

supply is required. It is recommended that a separate circuit

serving only your refrigerator and approved accessories be

provided. Use an outlet that cannot be turned off by a switch. Do

not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault

Circuit Interrupter) protected outlet, nuisance tripping of the power

supply may occur, resulting in loss of cooling. Food quality and

flavor may be affected. If nuisance tripping has occurred, and if

the condition of the food appears poor, dispose of the food.

NOTE: Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control

(Thermostat, Refrigerator or Freezer Control depending on the

model) to Off. On models with a digital temperature control, press

the minus sign touch pads repeatedly until a dash (-) appears in

both the freezer and refrigerator displays. Disconnect the

refrigerator from the electrical source. When you are finished,

reconnect the refrigerator to the electrical source and turn cooling

on or reset the control (Thermostat, Refrigerator or Freezer

Control depending on the model) to the desired setting. See the

“Quick Start Guide”.

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed:

�Flat-blade screwdriver

�7/16" and 1/2" Open-end or two

adjustable wrenches

�1/4" Nut driver

�1/4" Drill bit

�Cordless drill

�Connect to potable water supply only

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

�All installations must meet local plumbing code requirements.

�Do not use a piercing-type or 3/16" (4.76 mm) saddle valve

which reduces water flow and clogs more easily.

�Use copper or PEX tubing and check for leaks. Install copper

or PEX tubing only in areas where the household temperatures

will remain above freezing.

�For models with water filters, the disposable water filter should

be replaced at least every 6 months.

Water Pressure

A cold water supply with water pressure of between 35 and 120

psi (241 and 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

call a licensed, qualified plumber.

NOTE: If the water pressure is less than what is required, the flow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

�Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

�Allow the storage tank on the reverse osmosis system to refill

after heavy usage. The tank capacity could be too small to

keep up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are not

recommended.

�If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water Filtration

System”.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

�Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

�The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX (cross-

linked polyethylene) tube. Copper and PEX tubing connections

from the household water line to the refrigerator are

acceptable, and will help avoid off-taste or odor in your ice or

water. Check for leaks. If PEX tubing is used instead of copper,

we recommend the following part numbers:

W10505928RP (7 ft. [2.14 m] jacketed PEX),

8212547RP (5 ft. [1.52 m] PEX),

or W10267701RP (25 ft. [7.62 m] PEX).

�Install tubing only in areas where temperatures will remain

above freezing.

�Connect to a potable water supply only.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

Tools Needed:

Gather the required tools and parts before starting installation.

�Flat-blade screwdriver

�7/16" and 1/2" Open-end or two

adjustable wrenches

�1/4" Nut driver

�1/4" Drill bit

�Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35

mm) saddle-type shutoff valve, a union, and copper or PEX

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a piercing-

type or 3/16" (4.76 mm) saddle valve which reduces water flow

and clogs more easily.

Connect to Water Line

IMPORTANT: If you turn on the refrigerator before the water line is

connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

1/2" copper or PEX household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1/2" size copper or PEX household supply line is

recommended.

A. Bulb

B. Nut

C. Copper or PEX tubing (to

refrigerator)

D. Household supply line (½"

minimum)

4. Now you are ready to connect the copper or PEX tubing to the

shutoff valve. Use 1/4" (6.35 mm) O.D. (outside diameter) soft

copper or PEX tubing to connect the shutoff valve and the

refrigerator.

�Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

�Slip compression sleeve and compression nut onto copper

tubing as shown. (PEX tubing has compression sleeves

and compression nuts preinstalled.) Insert end of tubing

into outlet end squarely as far as it will go. Screw

compression nut onto outlet end with adjustable wrench.

Do not overtighten.

A. Compression

sleeve

B. Compression

nut

C. Copper or PEX tubing

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

6. Bend the copper or PEX tubing to meet the water line inlet,

which is located on the back of the refrigerator cabinet. Leave

a coil of copper or PEX tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Depending on your model, the water line may come down from

the top or up from the bottom. Follow the connection instructions

for your model.

Style 1

1. Remove plastic cap from water valve inlet port. Attach the

copper or PEX tube to the valve inlet using a compression nut

and sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper or PEX tubing is secure by pulling

on tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the tubing. Secure copper or PEX tubing to

refrigerator cabinet with a “P” clamp.

A. Copper or PEX

tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end

of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet’s side wall or other parts inside the cabinet.

A. Household water

line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install in the 1/4ʺ (6.35 mm) water line at either tube

connection. Obtain a water strainer from your appliance

dealer.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3–prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice.

Discard the first three batches of ice produced. Allow 3 days to

completely fill the ice storage bin.

2. Flush the water system. See “Water and Ice Dispensers.”

Install Air Filter (on some models)

The air filter reduces the buildup of odors. This helps to maintain a

cleaner environment inside your refrigerator. An air filter is 15

times more powerful than baking soda at reducing common food

odors inside the refrigerator.

Your refrigerator's accessory packet includes an air filter, which

must be installed prior to use. On some models, the air filter is

already installed at the factory.

Installing the Air Filter

Depending on your model, the air filter can be installed in one of

the following ways:

Style 1–Behind Vented Door:

Install the air filter behind the vented door, located on the rear wall

near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

NOTE: An air filter status indicator is included with the air filter.

The indicator is not needed for models that display the air filter

status on the control panel.

2. Lift open the vented door.

3. Snap the filter into place.

A. Air filter

Style 2–Behind LED Vent Cover

Install the air filter behind the blue vent LED-lighted cover, located

on the rear wall near the middle of the refrigerator.

1. Remove the air filter from its packaging.

2. Firmly grasp plastic cover on the vented cover with both hands

and pull out to remove.

NOTE: When cover is removed for the first time, a small foam

part the size of the filter will need to be discarded.

3. Snap the filter into place.

A. Air filter

Installing the Filter Status Indicator (on some

models)

The air filter icon on the control panel displays the air filter status.

�Blue: Good.

�Yellow: Order a replacement.

�Red: Replace air filter.

�Red and flashing “Replace Filter”: Expired.

After replacing the air filter, press and hold the Air Filter button for

3 seconds. The filter icons will turn off. See “Quick Start Guide.”

When the system is reset, the air filter icon will return to its blue

color and the words “Replace Filter” will disappear from the

control panel.

NOTE: At any filter status, pressing and holding the Air Filter

button for 3 seconds will reset the air filter status to Good and the

air filter icon will turn off.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, or

when the status indicator air filter icon turns on and starts flashing

when the refrigerator door is opened.

To order a replacement air filter, see ordering information in the

Quick Start Guide.

1. Remove the used air filter by squeezing in on the side tabs.

2. Install the new air filter and status indicator using the

instructions in the previous sections.

Air Filter Status Indicator—Standard Installation

The filter comes with a status indicator, which should be activated

and installed at the same time the air filter is installed.

1. Place the indicator facedown on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are

notches behind the door.

On models with notches:

�With the indicator screen facing outward, slide the indicator

down into the notches.

NOTE: The indicator will not easily slide into the notches if the

rear bubble has not been popped.

�Close the air filter door, and check that the indicator is visible

through the window in the door.

A. Status indicator window

B. Air filter status indicator

C. Notches

�Place the indicator in a visible place you will easily remember

—either inside the refrigerator or elsewhere in your kitchen or

home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when

the status indicator has completely changed from white to red.

To order a replacement air filter, see ordering information in the

Quick Start Guide.

1. Remove the used air filter by squeezing in on the side tabs.

2. Remove the used status indicator.

3. Install the new air filter and status indicator using the

instructions in the previous sections.

Install Produce Preserver (on some

models)

Your refrigerator's accessory packet includes a Produce

Preserver, which should be installed prior to use. On some

models, the Produce Preserver is already installed at the factory.

To order a replacement produce preserver, use part number

W10346771.

The Produce Preserver absorbs ethylene, allowing the ripening

process of many produce items to slow down. As a result, certain

produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Sensitivity to

Ethylene

Production

Apples High Very High

Asparagus Medium Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Medium High

Carrots Low Very Low

Citrus Fruit Medium Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Installing the Produce Preserver

CAUTION: IRRITANT. MAY IRRITATE EYES AND SKIN.

DANGEROUS FUMES FORM WHEN MIXED WITH OTHER

PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach,

or acids. Do not get in eyes, on skin or clothing. Do not breathe

dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If

swallowed, call a Poison Control Center or doctor immediately.

Do not induce vomiting. If in eyes, rinse with water for 15

minutes. If on skin, rinse with water.

Style 1– Located Inside the Refrigerator:

1. Find the Produce Preserver housing inside the refrigerator.

2. Lift up on the housing to remove it from the mounting tab.

3. Open the housing by pulling up and out on the back of the top

of the housing.

4. Remove the Produce Preserver pouches from the packaging.

Place them into the housing then snap housing back together.

NOTE: For best performance, always use two pouches.

5. Adhere the Produce Preserver housing to the back wall of the

crisper drawer according to the instructions included in the

package.

6. Place housing back on mounting tab.

Style 2–Located in Crisper or Refrigerator Drawers:

For your convenience, the suction-mounted produce preserver

can be installed in either the crisper or the refrigerated drawers.

1. Wash the interior of a drawer with a solution of mild dish soap

and warm water and dry thoroughly.

2. Find the package containing the Produce Preserver inside the

refrigerator and install the Produce Preserver into the drawer,

according to the instructions provided in the package.

Installing the Status Indicator

The Produce Preserver comes with a status indicator, which

should be activated and installed at the same time the pouch is

installed.

1. Place the indicator facedown on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not close easily if the indicator’s rear

bubble has not been popped.

Replacing the Produce Preserver Pouches

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, see the contact information in the Quick

Start Guide. Order part number W10346771A or FRESH1.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the new pouches and status indicator using the

instructions in the previous sections or instructions included in

the replacement packets.

REFRIGERATOR FEATURES

Crisper Humidity Control (on some

models)

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any setting

between Fruit and Vegetables or Low and High.

Fruit/Low (open):

Move control to allow moist air out of the crisper for best storage

of fruits and vegetables with skins.

�Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store in

a loosely closed paper bag on a refrigerator shelf.

�Vegetables with skins: Place in plastic bags or plastic

container and store in crisper.

Vegetables/High (closed):q

Move control to keep moist air in the crisper for best storage of

fresh, leafy vegetables.

�Leafy vegetables: Wash in cold water, drain and trim or tear off

bruised and discolored areas. Place in plastic bag or plastic

container and store in crisper.

Water and Ice Dispensers (on some

models)

For additional information on how to use your water and ice

dispensers, see the online “Dispensing Guide.”

IMPORTANT:

�After connecting the refrigerator to a water source or replacing

the water filter, flush the water system. Use a sturdy container

to depress and hold the water dispenser pad for 5 seconds,

then release it for 5 seconds. Repeat until water begins to flow.

Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total of

4 gal. (15 L) has been dispensed. This will flush air from the

filter and water dispensing system, and prepare the water filter

for use. Additional flushing may be required in some

households. As air is cleared from the system, water may spurt

out of the dispenser.

�Allow 24 hours for the refrigerator to cool down and chill water.

Dispense enough water every week to maintain a fresh supply.

�Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

�The dispenser will dispense either water or ice.

�The dispensing system will not operate when the refrigerator

door is open.

�On some models, the display screen on the dispenser control

panel will turn off automatically and enter “sleep” mode when

the control buttons and dispenser levers have not been used

for 2 minutes or more. While in “sleep” mode, the first press of

a control button will only reactivate the display screen without

changing any settings. After reactivation, changes to any

settings can then be made. If no changes are made within 2

minutes, the display will re-enter “sleep” mode.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system.

Flushing the water dispensing system forces air from the water

line and filter and prepares the water filter for use. Additional

flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps 1

and 2 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total of

3 gal. (12 L) has been dispensed.

The Water Dispenser

IMPORTANT:

Dispense at least 1 qt. (1 L) of water every week to maintain a

fresh supply.

If the flow of water from the dispenser decreases, it could be

caused by low water pressure.

�With the water filter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less, the

water pressure to the refrigerator meets the minimum

requirement.

�If it takes longer than 8 seconds to dispense 1 cup (237 mL) of

water, the water pressure to the refrigerator is lower than

recommended. See “Water Supply Requirements” and online

“Troubleshooting” for more information.

Cleaning the Ice Dispenser Chute

Humidity causes ice to naturally clump together. Ice particles can

build up until the ice dispenser chute becomes blocked.

If ice is not dispensed regularly, it may be necessary to empty the

ice storage bin and clean the ice delivery chute, the ice storage

bin and the area beneath the storage bin every 2 weeks.

�If necessary, remove the ice clogging the storage bin and

delivery chute, using a plastic utensil.

�Clean the ice delivery chute and the bottom of the ice storage

bin using a warm, damp cloth and dry thoroughly.

Ice Maker and Storage Bin

IMPORTANT:

To avoid low ice production and poor quality ice, flush the water

system before turning on the ice maker. See “Water and Ice

Dispenser” for details.

�Following installation, allow 24 hours to produce the first batch

of ice. Allow 2 to 3 days to fill the ice storage bin.

�For models with a water filter, after connecting the refrigerator

to a water source or replacing the water filter, fill and discard

three full containers of ice to prepare the water filter for use.

�The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

�If the ice in the storage bin clumps together, break up ice using

a plastic utensil and discard ice. Do not use anything sharp to

break up the ice. This can cause damage to the ice bin and the

dispenser mechanism.

�Do not store anything on top of the ice maker or in the ice

storage bin.

Ice Production Rate

Allow 24 hours to produce the first batch of ice. Discard the first

three batches of ice produced.

Allow 3 days to completely fill the ice storage bin. The ice maker

should produce approximately 3 lbs (1.4 kg) (8 to 12 batches) of

ice in a 24-hour period.

To increase ice production, lower the freezer and refrigerator

temperature, or see “Control Panel Descriptions” in the Quick

Start Guide for details. Wait 24 hours between adjustments.

Ice Maker in the Freezer

Turn the Ice Maker On/Off:

To turn on the ice maker, simply lower the wire shutoff arm.

To manually turn the ice maker off, lift the wire shutoff arm to the

off (arm up) position and listen for the click.

Your ice maker has an automatic shutoff. As ice is made, the ice

cubes will fill the ice storage bin and the ice cubes will raise the

wire shutoff arm to the off (arm up) position. Do not force the wire

shutoff arm up or down.

NOTE: Turn off the ice maker before removing the ice storage bin

to serve ice or to clean the bin. This will keep the ice cubes from

dropping out of the ice maker and into the freezer compartment.

After replacing the ice storage bin, turn on the ice maker.

Wash the ice storage bin with mild soap and warm water.

Slide the ice storage bin under the ice maker and push it toward

the back as far as it will go.

Auto Ice Storage Bin (on some models):

Your ice storage bin has a lever which allows the storage bin to

slide out with the drawer when it is pulled open or to stay in place.

�Move the lever to the right to attach the ice storage bin to the

freezer drawer.

�Move the lever to the left to release the ice storage bin from

the freezer drawer.

A. Ice storage bin lever

Ice Maker in the Refrigerator (on some models)

Style 1— Left-Hand Refrigerator Door

The ice maker is located on the left-hand side of the refrigerator

door. Ice cubes are ejected into the ice storage bin, located on the

left-hand refrigerator door.

Turn the Ice Maker On/Off:

1. Push up on the latch on the left-hand side of the ice

compartment to open the door.

A. Ice compartment door latch

2. Turn on the ice maker by moving the switch to the (left) on

position.

�To manually turn off the ice maker, move the control to the

off (right) position.

�Your ice maker has an automatic shutoff. The sensor will

automatically stop ice production if the storage bin is full, if

the door is open or the storage bin is removed. The control

will remain in the on (left) position.

A. Ice storage bin release latch

3. Close the ice compartment door.

Remove and Replace the Ice Storage Bin:

�Remove the ice storage bin by inserting your fingers into the

hole at the base of the bin and squeezing the latch to release

the bin from the compartment. Lift the storage bin up and pull it

straight out.

�Replace the storage bin inside the ice compartment and push

down to make sure it is firmly in place.

IMPORTANT: The ice storage bin has a magnet. In accordance

with guidelines from the American Heart Association, as with

many products containing magnets, it is recommended that those

with implantable pacemakers/defibrillators should use care with

the ice storage bin and keep their device 30 cm (12 inches) away

from the ice storage bin.

Style 2— Upper Left-Hand Side of the Refrigerator

Compartment

The ice maker and storage bin are located in the upper left-hand

side of the refrigerator compartment.

Turn the Ice Maker On/Off:

The ice maker has an automatic shutoff. When the ice maker is

on, sensors will automatically stop ice production when the

storage bin is full. The ice maker will remain set to on, and ice

production will resume when the bin is no longer full.

NOTE: Some models have an on/off switch located on the ice

maker storage bin. To turn on the ice maker, press the switch to

the On position. To manually turn off the ice maker, press the

switch to the Off position.

To manually turn off the ice maker, see the Quick Start Guide for

more information.

Remove and Replace the Ice Storage Bin:

1. Hold the base of the storage bin and press the release button

on the lower right.

2. Pull out the storage bin until resistance is felt. Lift up the front

of the ice bin and remove.

3. Press the switch to Off (on some models).

IMPORTANT: To remove the ice storage bin, it may be necessary

to turn the auger driver, behind the ice bin, counterclockwise to

properly align the ice bin with the auger driver. The ice storage bin

must be locked in place for proper ice dispensing.

A. On position (on some models)

B. Auger driver

1. Press the switch to On (on some models).

2. Slide the ice bin into the guide rails located on either side of

the enclosure.

3. Push the ice bin in until resistance is felt. Raise the front

slightly and push the ice bin in until an audible “click” is heard.

Style 3— Left-Hand Door Behind the Refrigerator Bins

The ice maker is located on the left door behind the bins. Ice

cubes are ejected into the ice storage bin located on the left-hand

refrigerator door.

Turn the Ice Maker On/Off:

1. Push up on the latch on the left-hand side of the ice

compartment to open the door.

2. Turn on the ice maker by moving the switch to the On (I)

position.

3. Close the ice compartment door.

Remove and Replace the Ice Storage Bin:

�Remove the ice storage bin by inserting your fingers into the

hole at the base of the bin and squeezing the latch to release

the bin from the compartment. Lift the storage bin up and pull it

straight out.

�Replace the storage bin inside the ice compartment and push

down to make sure it is firmly in place.

Water Filtration System

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the

system. Systems certified for cyst reduction may be used on

disinfected waters that may contain filterable cysts.

IMPORTANT: The disposable water filter should be replaced at

least every 6 months. If the water flow to the water dispenser or

ice maker decreases noticeably before 6 months have passed,

replace the water filter more often.

Install the Water Filter

To order a replacement filter, contact us at www.whirlpool.com/

Parts & Accessories. See the “Quick Start Guide” for details.

NOTE: If the filter is not installed correctly, water may dispense at

a lower flow rate and there will be slower ice production. Improper

filter installation may also cause the water filter housing to leak.

Style 1 — Bottom Left of Refrigerator Compartment

1. Push the water filter door to open, located bottom left of

refrigerator compartment.

2. Twist the water filter and turn 90° counterclockwise to unlock.

3. Pull the filter out of the housing.

4. Remove the water filter cap from the water filter.

5. Install the water filter cap onto the new filter. Be sure to align

the arrows so the grooves in the filter align with ribs in the filter

cap.

6. Insert the filter into the housing.

7. Twist the water filter and turn 90° clockwise until it locks into

place and the arrows are aligned.

8. Push the water filter door closed.

Style 2— Right-Hand Side of Refrigerator Ceiling

1. Locate the accessory packet in the refrigerator and remove

the water filter.

2. Take the water filter out of its packaging and remove the cover

from the O-rings. Be sure the O-rings are still in place after the

cover is removed.

A. O-ring cover

B. O-rings

3. The water filter compartment is located in the right-hand side

of the refrigerator ceiling. Push up on the compartment door to

release the catch, then lower the door.

4. Align the arrow on the water filter label with the cutout notch in

the filter housing and insert the filter into the housing.

5. Turn the filter clockwise 90 degrees (1/4 turn), until it locks into

the housing.

NOTE: If the filter is not correctly locked into the housing, the

water dispenser will not operate. Water will not flow from the

dispenser.

6. While the compartment door is still open, lift the filter up into

the compartment. Then, close the filter compartment door

completely.

7. Flush the water system. See “Water and Ice Dispensers” for

details.

IMPORTANT: If you do not flush the water system, you may

experience dripping and/or decreased flow from the water

dispenser.

Replacing the Water Filter

To purchase a replacement water filter, use model number

P9WBL2 (EDR2RXD1), contact your dealer, or call 1-800-422-

9991 1-800-807-6777in the U.S.A. or in Canada.

IMPORTANT: Air trapped in the water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. If applicable, press upward on the water filter cover to access

the filter.

2. Turn filter counterclockwise, and pull straight out to remove.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

3. Remove sealing label from replacement filter and insert the

filter end into the filter head.

4. Turn the filter clockwise until it stops. Snap the filter cover

closed.

5. Flush the water system. See “Water and Ice Dispensers” for

details.

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

Reset Water Filter Status

After replacing the water filter, press and hold Reset Filter or Filter

Reset (depending on your model) for 3 seconds. The Order and

Replace indicator lights will blink and then go off when the system

is reset. On some models the indicator light will change to blue

when the system is reset. See the “Quick Start Guide” for more

information.

On models with Options and Measured Fill buttons located

on the control panel:

After changing the water filter, reset the status light. Press the

Options button to enter Options mode, then press Lock to initiate

the reset, then press Measured Fill to confirm that you want to

reset the status light. When the system is reset, the “Order” and

“Replace” icons will disappear from the display screen.

On models with Water Filter button located on the control

panel:

After changing the water filter, reset the status. Press and hold the

Water Filter button for 3 seconds. When the system is reset, the

water filter icon will return to Blue and the words “Replace Filter”

will disappear from the display.

DOOR AND HANDLE

INSTRUCTIONS

Door and Drawers

Depending on the width of your doorway, you may need to remove

the doors to move the refrigerator into your home. Also, the door

hinges are factory installed on the right-hand side. If you want the

door to open from the other direction, you must reverse the door

swing.

IMPORTANT:

�If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control Off, and unplug the refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

�Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet. Provide additional support for the

refrigerator door while the hinges are being removed. Do not

depend on the door gasket magnets to hold the door in place

while you are working.

Tools Needed: 5/16", 3/8", and 1/4" hex head socket wrenches,

Torx®† T25 screwdriver, #2 Phillips screwdriver, and a flat-blade

screwdriver.

Remove and Replace Handles

REFRIGERATOR DOOR HANDLES

Refrigerator Door Handle Style 1

A. 3/32" Setscrew

�Using a 3⁄32" or 1⁄8" hex key,

loosen the two setscrews located

on the side of each handle. Pull

the handle straight out from the

drawer. Make sure you keep the

screws for reattaching the

handles.

�To replace the handles, reverse

the directions.

Refrigerator Door Handle Style 2

A. Handle Trim C. Refrigerator Door Handle

B. Flat–Head Handle Screws

�Remove the screw cover.

�Remove the handle assembly. Keep all parts together.

�To replace the handles, reverse the directions.

Refrigerator Door Handle Style 3

A. Flat–Head Handle Screws B. Refrigerator Door Handle

�Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from

the drawer. Make sure you keep the screws for reattaching the

handles.

�To replace the handles, reverse the directions.

Refrigerator Door Handle Style 4

A. 3/32" or 1/8" Setscrews

�To remove the handle, remove the screw attaching the trim to

the upper end of the handle. Using a flat-blade screwdriver

wrapped in masking tape, pry the trim piece from the lower end

of the handle. Then, remove the screws attaching the handle

to the door.

�To replace the handles, reverse the directions.

Refrigerator Door Handle Style 5

�To remove the handle, grasp the

lower part of the handle firmly,

slide the handle up and pull the

handle straight out from the door.

�To replace the handle, position the

handle so that the large holes in

the mounting clips are down and

align the holes with the door studs.

Rotate the handle so that the

mounting clips are flat against the

door and slide the handle down to

engage.

FREEZER DOOR HANDLES

Freezer Door Handle Style 1

A. 3/32" Setscrew

�Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from

the drawer. Make sure you keep the screws for reattaching the

handles.

�To replace the handles, reverse the directions.

Freezer Door Handle Style 2

A. 3/32" or 1/8" Setscrews

�Using a 3⁄32" or 1⁄8" hex key, loosen the two setscrews located

on the side of each handle. Pull the handle straight out from

the drawer. Make sure you keep the screws for reattaching the

handles.

�To replace the handles, reverse the directions.

Freezer Door Handle Style 3

A. Flat–Head Handle Screws

�Remove screws and handle.

�To replace the handles, reverse the directions.

Freezer Door Handle Style 4

A. Flat–Head Screws B. Freezer Drawer Handle

�Remove screws and handle.

�To replace the handles, reverse the directions.

Freezer Door Handle Style 5

�To remove the handle, grasp the lower part of the handle

firmly, slide the handle up and pull the handle straight out from

the door.

�To replace the handle, position the handle so that the large

holes in the mounting clips are down and align the holes with

the door studs. Rotate the handle so that the mounting clips

are flat against the door and slide the handle down to engage.

Remove Refrigerator Doors and

Hinges

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so could result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Remove base grille.

BASE GRILLE

Style 1

�Using both hands, grasp the grille firmly and pull it toward you.

Open the freezer drawer to access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the brake

feet by turning them counterclockwise. The front rollers will be

touching the floor.

Style 2

�Remove the two screws fastening the base grille to the cabinet

and set screws aside.

�Grasp the grille and pull it toward you.

NOTE: To allow the refrigerator to roll easier, raise the brake

feet by turning them counterclockwise. The front rollers will be

touching the floor.

Style 3

�Use a 1/4" hex–nut driver to remove both screws in the base

grille.

�Using both hands, grasp the grille firmly and pull it toward you.

Open the freezer drawer to access the brake feet.

NOTE: To allow the the refrigerator to roll easier, raise brake

feet by turning The rollers them counterclockwise. front will be

touching the floor.

Remove Right-Hand Refrigerator Door

3. Starting with the right-hand side door, remove the parts for the

top hinge as shown below.

A. Top hinge cover screw D. Top Hinge

B. Top hinge cover E. Locator Screws

C. 3/16" Internal hex-head screws

NOTE: Do not remove the two locator screws. These screws

will help you align the hinge when you replace the door.

WARNING

Excessive Weight Hazard

Use two or more people to lift the appliance door.

Failure to do so can result in back or other injury.

4. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

Remove Left-Hand Refrigerator Door

IMPORTANT: On models with a water dispenser, the tubing and

wiring for the water dispenser run through the left-hand door

hinge, so they must be disconnected before removing the door.

1. Remove the cover from the top hinge as shown below.

A. Top hinge cover screw B. Top hinge cover

2. Disconnect the water dispenser tubing located on top of the

door hinge (if applicable).

Water Tubing Connection Style 1: Press the colored outer ring

against the face of the fitting and gently pull the dispenser tubing

free as shown below.

NOTE: The water dispenser tubing remains attached to the left-

hand refrigerator door.

A. Outer ring B. Face of fitting

3. Before removing the left-hand side door, disconnect the wiring

plug located on top of the top hinge by wedging a flat-blade

screwdriver or your fingernail between the two sections.

NOTE: Do not remove the green, ground wire. It should

remain attached to the door hinge.

A. 3/4” Internal hex-head or

TORX T25 screws C. Locator screws (do not

remove)

B. Ground wire (Do not remove)

4. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

�Only if necessary, depending on your model, use a driver

with a #2 square bit tip or a TORX T25 screwdriver to

remove the bottom hinges and a 3/8" nut driver or a TORX

T25 screwdriver to remove the brake feet screws.

Reset Bottom Refrigerator Door

Hinge

For your convenience, the refrigerator doors have bottom hinges

with door closers. These closers allow the doors to swing fully

closed with just a gentle push.

IMPORTANT: So that the closers feature will operate properly, the

doors must be removed only when open to a 90° angle to the front

of the cabinet. If one or both doors were not at a 90° angle when

removed, the bottom door hinge must be reset.

RESET THE DOOR HINGE

1. Lift the door from the bottom hinge pin and place it on a flat

surface.

2. Using a driver with a #2 square bit, remove the bottom hinge

with the bushing from the cabinet.

A. Bushing B. Hinge base

3. Insert the bottom hinge and bushing into the corresponding

slot in the bottom of the door.

NOTE: Make sure that the base of the hinge is parallel to the

bottom of the door.

A. Hinge base parallel to the bottom edge of the door

4. Turn the hinge until the hinge base is at a 90° angle to the

bottom edge of the door.

A. Hinge base turned to a 90° angle with the bottom edge of

the door

5. Remove the hinge from the door. Reattach the bottom hinge to

the refrigerator cabinet.

6. The hinge is now reset and prepared for the door to be

replaced.

Replace Refrigerator Doors and

Hinges

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Fasten the hinge to the cabinet. Do not tighten the screws

completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them

1. Set the left-hand door onto the bottom hinge pin.

2. Fasten the hinge to the cabinet. Do not tighten the screws

completely.

3. If applicable, reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the

outer ring is touching the face of fitting.

Style 2 - Insert the tubing firmly into the fitting until it stops.

Close the clasp around the tubing. The clasp snaps into place

between the fitting and the collar.

4. Reconnect the electrical wiring.

�Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the internal screws

2. Replace both top hinge covers.

Remove and Replace Refrigerator

Drawer

Depending on the width of your door opening, it may be necessary

to remove the drawer fronts to move the refrigerator into your

home.

REMOVE DRAWER FRONT

IMPORTANT:

�If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control Off, and unplug the refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

�Two people may be required to remove and replace the

freezer drawer. Graphics are included later in this section.

Tools Needed: 1/4" Hex head nut driver, Flat-blade screwdriver

Disconnect Wiring (if applicable)

NOTES:

�The exterior refrigerator drawer front is connected to the

temperature control on some models. Before removing the

drawer front, the wires must be disconnected from the

temperature control.

�The gray cable visible behind and under the pantry drawer at

the right side contains wiring for the pantry control and moves

with the drawer as it is pulled out. There is no need to

disconnect this cable.

1. Open the drawer to its full extension, and remove the interior

bin.

2. Left-hand drawer only: Remove the wiring connection cover.

Press in on the side of the cover to release the tab from the

slot, and then pull the cover away from the bracket.

A. Cover tab B. Wiring connection cover

3. Left–hand drawer only, disconnect the wiring.

NOTE:

�On one side of the wiring connector, insert the screwdriver

blade between the connector tab and the connector to

release. Repeat for the opposite side. Pull the wiring

connector apart.

4. Remove the drawer front.

Style 1: Bottom Release Lever

�Push up on the lever at the bottom of the drawer glide bracket

to release the drawer front from the bracket.

�Lift the drawer front up and off the drawer glide brackets.

A. Drawer glide bracket B. Release lever

Style 2: Bottom Screws

�Loosen the two top screws attaching the drawer glide brackets

to the drawer front.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

�Remove the two bottom screws attaching the drawer glide.

�Lift the drawer front up and off the top screws.

A. Four Bracket screws

5. Slide the drawer glides back into the refrigerator.

REPLACE DRAWER FRONT

1. Pull out the drawer glides until they are full extended.

2. Style 1: Bottom Release Lever

�Push up on the lever at the bottom of the drawer glide

bracket to open. Insert the drawer front bracket into the

drawer glide bracket and release the lever.

Style 2: Bottom Screws

�Lower the loosened screws in the top of the door front into

the upper notches in the drawer glide.

�Align the holes in the bottom of the drawer glides.

�Replace two screws removed previously and tighten all

four screws.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

screws into the notches.

3. Reconnect Wiring (if applicable)

�Align the two ends of the wiring connector and push them

together until you hear a click sound and feel the tabs snap

into place on the connector.

�Gently pull on the wiring connection to ensure the wiring

connection is completely seated. Replace the wiring cover.

NOTE: The wiring connection must be complete for the

drawer temperature control to operate.

4. Replace the drawer bins onto the drawer glides.

Remove and Replace Freezer Drawer Front

Depending on the width of your door opening, it may be necessary

to remove the freezer drawer front to move the refrigerator into

your home.

IMPORTANT:

�If the refrigerator was previously installed and you are moving

it out of the home, before you begin, turn the refrigerator

control Off, and unplug the refrigerator or disconnect power.

Remove food and any adjustable door or utility bins from

doors.

�Two people may be required to remove and replace the

freezer drawer

Tools Needed: 1/4" hex driver

REMOVE DRAWER

Front Style 1 & 2

1. Open the freezer drawer to its full extension.

2. Loosen the two screws at the top, inside the drawer front (one

on the left-hand side and one on the right-hand side) that

fasten the drawer front to the drawer glides as shown below.

3. Remove the 2 screws at the bottom, inside the drawer front

that fasten the drawer front to the drawer glides as shown

below.

4. Lift up on the drawer front to release the plastic studs from the

drawer glide bracket slots as shown below.

Style 1 Style 2

A. Drawer glide bracket slots A. Drawer glide bracket slots

5. Slide the drawer glides back into the freezer.

Front Style 3

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front as shown below.

NOTE: Loosen screws three to four turns. Keep the screws in the

drawer front.

A. Four Bracket screws

3. Lift drawer front upward and off the screws.

REPLACE DRAWER

Front Style 1 and 2

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the two plastic

studs, located at the bottom, inside the drawer front, with the

drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

studs into the slots.

Style 1 Style 2

A. Drawer front screw A. Drawer front screw

B. Drawer front plastic stud

3. Replace and tighten the two screws at the top of the drawer

front (one on the left-hand side and one on the right-hand

side).

Front Style 3

1. Slide the drawer glides out of the freezer compartment.

2. Insert the screws in the top of the drawer into the slots in the

drawer brackets.

3. Completely tighten all four screws.

Door Closing and Alignment

The base grille covers the adjustable brake feet and roller

assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the base

grille and move the refrigerator to its final location.

Tools Needed: Tools Provided:1/4" hex driver 1/8" hex key

1. Remove base grille.

BASE GRILLE

Style 1

Final Steps

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet

2. Reset the controls. See “Control Panel Descriptions” in the

Quick Start Guide for details.

3. Return all removable door parts to doors and the food to

refrigerator.

Align Refrigerated Drawer Fronts (on some

models)

When the drawer fronts are aligned, the width of the vertical space

(A) between the refrigerator doors (B) and the drawer fronts (C) is

the same thickness, and the drawers appear level.

A. Vertical space between doors C. Drawer fronts

B. Drawer fronts

Aligning the drawer fronts is a two-step process. The first step is

to adjust the drawer fronts up and down. The second step shifts

the drawer fronts from side to side. Visually inspect the

refrigerator for alignment and adjust the drawer fronts as needed.

Step 1 - Adjust the Drawer Fronts Up/Down

IMPORTANT: Each refrigerated drawer can be adjusted up and

down on both the left and the right sides.

Tools Needed: Phillips screwdriver

1. With the drawers closed, identify the drawer front that needs

to be raised or lowered.

2. Open the drawer to its full extension, and remove the interior

bin.

3. Locate the drawer glide brackets.

A. Drawer glide brackets

4. Insert the Phillips screwdriver into tightening screw and turn

counterclockwise to loosen the drawer front.

A. Tightening screw B. Adjusting screw

5. Insert the Phillips screwdriver into adjusting screw to adjust

the drawer front.

IMPORTANT: The direction you turn the adjusting screw

depends on which side of the drawer you are adjusting.

Left-Hand Side Drawer Glide

�To raise the drawer front, turn adjusting screw clockwise.

�To lower the drawer front, turn adjusting screw

counterclockwise.

Right-Hand Side Drawer Glide

�To raise the drawer front, turn adjusting screw

counterclockwise.

�To lower the drawer front, turn adjusting screw clockwise.

6. Insert the Phillips screwdriver into tightening screw, and turn

clockwise to tighten the drawer front.

7. Close the refrigerated drawer to check the alignment. Repeat

steps 2 through 6 until the drawer fronts are level.

Step 2 - Adjust the Drawer Fronts Side to Side

IMPORTANT: Each refrigerated drawer can be adjusted side to

side on both the left and right side.

1. With the drawers closed, identify the drawer that is not

aligned.

2. Open the drawer to its full extension, and remove the interior

bin.

3. Locate the drawer glide brackets.

4. Starting with the glide bracket closest to the vertical gap, press

and hold the release lever up. With your other hand, lift the

door clip from the drawer glide bracket.

A. Drawer front clip C. Release lever

B. Drawer glide bracket

5. Reposition the drawer front clip onto the drawer glide bracket

in the direction you want to move the drawer front. Make sure

that the glide bracket is vertically level.

6. Release the lever to lock the glide bracket into position.

7. Repeat steps 3 through 6 for the other side of the drawer front.

NOTE: Adjust the clip on the top of the second glide bracket

so that it is in the same position as the side you adjusted first.

8. Close the drawer and visually inspect the gap. Repeat steps 2

though 7 until the drawer fronts are aligned.

FINAL STEPS

1. Replace the interior drawer bins.

NOTE: The bins must be placed into the drawers correctly so

that the refrigerated drawers will close and operate properly.

See “Remove and Replace Drawer Fronts.”

2. Close the refrigerated drawers.

Water Filtration System

Model P9WB2L/EDR2RXD1B Capacity 200 Gallons (757 Liters)

Replacement Filter EDR2RXD1, EDR2RXD1B, WHR2RXD1, and KAD2RXD1

System tested and certified by NSF International against NSF/ANSI Standard

42, 53, 401 and CSA B483.1 for the reduction of contaminants specified on the

Performance Data Sheet.

This system has been tested by an independent laboratory according to NSF/ANSI Standards 42, 53, 401 and CSA B483.1 for the

reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a

concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42, 53, 401

and CSA B483.1.

Substance Reduction

Aesthetic Effects

Influent Challenge

Concentration

Maximum Permissible

Product Water Concentration

Average % Reduction

Chlorine Taste/Odor Particulate

Class I*

2.0 mg/L ± 10% At least 10,000

particles/mL

50% reduction 85% reduction 97.2%

Contaminant Reduction Influent Challenge

Concentration

Maximum Permissible

Product Water Concentration

Average % Reduction

Lead: @ pH 6.5 / @ pH 8.5 0.15 mg/L ± 10% 0.010 mg/L >99.3% / 98.6%

Benzene 0.015 mg/L ± 10% 0.005 mg/L 96.0%

P-Dichlorobenzene 0.225 mg/L ± 10% 0.075 mg/L >99.8%

Carbofuran 0.08 mg/L ± 10% 0.040 mg/L 91.9%

Toxaphene 0.015 ± 10% 0.003 mg/L 93.3%

Atrazine 0.009 mg/L ± 10% 0.003 mg/L 92.4%

Asbestos 107to 108fibers/L†† 99% >99%

Live Cysts† 50,000/L min. 99.95% >99.99%

Turbidity 11 NTU ± 10% 0.5 NTU 99.0%

Lindane 0.002 ± 10% 0.0002 mg/L 98.9%

Tetrachloroethylene 0.015 mg/L ± 10% 0.005 mg/L >96.6%

o-Dichlorobenzene 1.8 mg/L ± 10% 0.60 mg/L >99.9%

Ethylbenzene 2.1 mg/L ± 10% 0.70 mg/L 99.4%

1,2,4-Trichlorobenzene 0.210 mg/L ± 10% 0.07 mg/L >99.8%

2,4 - D 0.210 mg/L ± 10% 0.07 mg/L 93.8%

Styrene 2.0 mg/L ± 10% 0.1 mg/L 99.8%

Toluene 3.0 mg/L ± 10% 1.0 mg/L 87.9%

Endrin 0.006 mg/L ± 10% 0.002 mg/L >96.6%

Atenolol 200 ± 20% 30 ng/L >95.9%

Trimethoprim 140 ± 20% 20 ng/L >96.9%

Linuron 140 ± 20% 20 ng/L >96.4%

Estrone 140 ± 20% 20 ng/L >97.0%

Nonylphenol 1400 ± 20% 200 ng/L >97.4%

Carbamazepine 1400 ± 20% 200 ng/L >97.9%

PERFORMANCE DATA SHEET

Phenytoin 200 ± 20% 30 ng/L 93.8%

Naproxen 140 ± 20% 20 ng/L 96.1%

Bisphenol A 2000 ± 20% 300 ng/L >99.2%

Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.6 gpm (2.27 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to

71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

The compounds certified under NSF 401 have been deemed as “emerging compounds/incidental contaminants.” Emerging compounds/

incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels. While occurring at only

trace levels, these compounds can affect the public acceptance/perception of drinking water quality.

�For installation, operation, and maintenance instructions please

refer to the Owner's Manual.

�It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised. Property damage can occur if all

instructions are not followed.

�The disposable cartridge must be changed at least every 6

months.

�Use replacement filter part #EDR2RXD1/EDR2RXD1B. 2015

suggested retail price of $49.99 U.S.A./$49.99 Canada. Prices

are subject to change without notice.

�The filter monitor system measures the amount of water that

passes through the filter and alerts you when it is time to replace

the filter. Refer to the “Using the Controls” or “Water Filtration

System” section (in the User Instructions or User Guide) to learn

how to check the water filter status.

�After changing the water filter, flush the water system. See

“Water and Ice Dispensers” or “Water Dispenser” in the User

Instructions or User Guide.

�These contaminants are not necessarily in your water supply.

While testing was performed under standard laboratory

conditions, actual performance may vary.

�For installation, operation and maintenance instructions please

refer Owner's Manual.

Consumer Support 1.800.442.9991

By Whirlpool Corporation

2000 North M63

Benton Harbor, MI 49022

Made in Taiwan.

�The product is for cold water use only.

�The water system must be installed in compliance with state

and local laws and regulations.

�Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used on

disinfected waters that may contain filterable cysts. EPA Est.

No. 082047-TWN-001

�Refer to the “Warranty” section for the Manufacturer’s limited

warranty, name and telephone number.

Application Guidelines/Water Supply Parameters

Water Supply Potable City or Well

Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33° - 100°F (0.6° - 37.8° C)

Service Flow Rate 0.6 GPM (2.27 L/min.) @ 60

psi. (413.7 kPa)

�Your water filtration system will withstand up to 120 pounds per

square inch (psi) water pressure. If your water supply is higher

than 80 psi, install a pressure reducing valve before installing

the water filtration system.

*Class I particle size: >0.5 to 1 um

†Based on the use of Cryptosporidium parvum oocysts

††Fibers greater than 10 um in length

®NSF is a registered trademark of NSF International.

Votre sécurité et celle des autres sont très importantes.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil. Assurez-vous de toujours lire

tous les messages de sécurité et de vous y conformer.

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot « DANGER » ou

« AVERTISSEMENT ». Ces mots signifient :

DANGER Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

AVERTISSEMENT Risque possible de décès ou de blessure grave si vous ne

suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel, comment réduire le risque de blessure et ce qui peut se

produire en cas de non-respect des instructions.

INSTRUCTIONS IMPORTANTES DE SÉCURITÉ

AVERTISSEMENT : Afin de réduire le risque d’incendie, de décharge électrique ou de blessures corporelles lors de l’utilisation

de cet appareil, observer certaines précautions fondamentales, notamment :

�Les enfants doivent être surveillés afin de s’assurer qu’ils

ne jouent pas avec l’appareil.

�Cet appareil ne convient pas à une utilisation par des

personnes (y compris des enfants) à capacités physiques,

sensorielles ou mentales réduites, ou possédant un

manque d’expérience et de connaissances, à moins

qu’elles ne soient placées sous supervision ou qu’elles

aient reçu des instructions concernant l’utilisation de

l’appareil par une personne responsable de leur sécurité.

�Ne pas utiliser de rallonge.

�Si le cordon d’alimentation est endommagé, il doit être

remplacé par le fabricant, son agent de réparation ou toute

autre personne qualifiée afin d’éviter tout danger.

�Brancher sur une alimentation en eau potable uniquement.

�Cet appareil est destiné à un usage domestique et à

d’autres usages similaires comme : coins cuisine réservés

au personnel des boutiques, des bureaux et d’autres

environnements professionnels; maisons d’hôtes, ainsi que

par les clients d’hôtel, de motels et d’autres installations

d’hébergement; gîtes touristiques; et banquets et autres

utilisations non commerciales semblables.

�Ne pas entreposer de substances explosives comme des

aérosols avec agent propulseur inflammable dans cet

appareil.

�Ne pas utiliser de pièces de remplacement qui n’ont pas

été recommandées par le fabricant (c.-à-d., pièces

fabriquées à la maison à l’aide d’une imprimante 3D).

�Garder les évents à l’intérieur de l’enceinte de l’appareil ou

de la structure encastrée exempte d’obstacles.

�Ne pas utiliser des appareils mécaniques ou autres

moyens pour accélérer le processus de dégivrage, autre

que ceux recommandés par le fabricant.

�Ne pas endommager le circuit réfrigérant.

�Ne pas utiliser des appareils électriques à l’intérieur des

compartiments d’aliments de l’appareil, à moins qu’ils

soient de type recommandé par le fabricant.

CONSERVER CES INSTRUCTIONS

SÉCURITÉ DU RÉFRIGÉRATEUR

Nettoyage de l’intérieur :

IMPORTANT : Les tablettes du réfrigérateur équipées d’éclairage

DEL par en dessous ne sont pas lavables au lave-vaisselle.

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Laver à la main, rincer et sécher les pièces amovibles et les

surfaces internes soigneusement. Utiliser une éponge propre

ou un linge doux et un détergent doux dans de l’eau tiède.

3. Brancher le réfrigérateur ou reconnecter la source de courant

électrique.

Nettoyage de l’extérieur :

IMPORTANT : Les dommages au revêtement lisse en raison d’un

mauvais usage des produits nettoyants ou de l’utilisation de

produits nettoyants non recommandés ne sont pas couverts par la

garantie. Des instruments aiguisés ou coupants dépareraient le

revêtement.

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. À l’aide d’une éponge propre ou d’un chiffon doux et d’un

détergent doux dans de l’eau tiède, laver, rincer et sécher

soigneusement les pièces extérieures en acier inoxydable et

surfaces métalliques peintes.

Pour que votre réfrigérateur en acier inoxydable conserve son

aspect neuf et pour enlever les petites égratignures ou

marques, il est suggéré d’utiliser le nettoyant et poli pour acier

inoxydable approuvé par le fabricant. Ce nettoyant doit être

utilisé sur les pièces en acier inoxydable uniquement.

Consulter le Guide de démarrage rapide pour les informations

de commande.

REMARQUE : Lors du nettoyage de l’acier inoxydable,

toujours frotter dans le sens du grain afin d’éviter d’érafler la

surface.

Veiller à ce que le nettoyant et poli pour acier inoxydable

n’entre pas en contact avec les pièces de plastique comme

les garnitures, couvercles de distributeurs ou joints de porte.

En cas de contact non intentionnel, nettoyer la pièce de

plastique avec une éponge et un détergent doux dans de l’eau

tiède. Sécher soigneusement avec un chiffon doux.

3. Brancher le réfrigérateur ou reconnecter la source de courant

électrique.

Style 1 : Porte lisse/métal peint

UTILISER NE PAS UTILISER

� �Chiffon doux et propre Chiffons abrasifs

�Essuie-tout ou papier

journal

�Tampons de laine d’acier

�Eau tiède et savonneuse

avec détergent doux

�Poudres ou liquides

abrasifs

�Nettoyants à vitre en

vaporisateur

�Ammoniaque

�Nettoyants acides ou à

base de vinaigre

�Nettoyants à four

�Fluides inflammables

REMARQUE : Les essuie-tout peuvent érafler et ternir le

revêtement transparent de la porte peinte. Afin d’éviter tout

dommage éventuel, utiliser des chiffons en tissu doux pour polir et

essuyer les portes.

Style 2 :Acier inoxydable

UTILISER NE PAS UTILISER

� �Chiffon doux et propre Chiffons abrasifs

�Essuie-tout ou papier

journal

�Tampons de laine d’acier

�Eau tiède et savonneuse

avec détergent doux

�Poudres ou liquides

abrasifs

�Ammoniaque

�Nettoyants à base

d’agrumes

�Nettoyants acides ou à

base de vinaigre

�Nettoyants à four

�Pour les saletés

importantes, utiliser

seulement le nettoyant et

poli pour acier inoxydable

approuvé par le fabricant

�Poudres ou liquides

abrasifs

�Ammoniaque

�Nettoyants à base

d’agrumes

�Nettoyants acides ou à

base de vinaigre

�Nettoyants à four

�Chiffons abrasifs

�Essuie-tout ou papier

journal

�Tampons de laine d’acier

REMARQUES :

�En cas de contact non intentionnel, nettoyer la pièce de

plastique avec une éponge et un détergent doux dans de l’eau

tiède. Sécher soigneusement avec un chiffon doux.

�Ne pas exposer les électroménagers en acier inoxydable à

des éléments caustiques ou corrosifs tels que le sel, un niveau

élevé d’humidité ou des environnements très humides. Les

dommages causés par l’exposition à de tels éléments ne sont

pas couverts par la garantie.

�Un nettoyant sous forme liquide ne signifie pas forcément qu’il

n’est pas abrasif. Beaucoup de nettoyants liquides formulés

pour nettoyer le carrelage et autres surfaces lisses en douceur

peuvent tout de même endommager l’acier inoxydable.

�Lors du nettoyage de l’acier inoxydable, toujours frotter dans le

sens du grain afin d’éviter d’érafler la surface.

�L’acide citrique décolore l’acier inoxydable de façon définitive.

Afin d’éviter d’endommager le fini en acier inoxydable du

réfrigérateur :

Ne pas laisser les produits suivants pendant une durée

prolongée sur le revêtement :

• Moutarde

• Jus de tomates

• Sauce marinara

• Sauces à base d’agrumes

• Produits à base d’agrumes

Nettoyage du condensateur

AVERTISSEMENT

Risque d’explosion

Risque d’incendie ou d’explosion causé par la

perforation de la tubulure de réfrigération;

suivre avec attention les instructions de manipulation.

Fluide frigorigène inflammable utilisé.

Le condensateur n’a pas besoin d’être nettoyé souvent dans des

conditions de fonctionnement domestique normales. Si

l’environnement est particulièrement graisseux, poussiéreux ou

s’il y a des animaux domestiques dans la maison, le condenseur

devrait être nettoyé tous les 6 mois pour assurer une efficacité

maximum.

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Retirer la grille de la base.

3. Utiliser un aspirateur à brosse douce pour nettoyer la grille,

les endroits ouverts derrière la grille et la surface à l’avant du

condensateur.

4. Replacer la grille de la base après avoir terminé.

5. Brancher le réfrigérateur ou reconnecter la source de courant

électrique.

REMARQUE : Communiquer avec le service s’il est impossible de

nettoyer le condensateur.

Remplacer l’ampoule d’éclairage

IMPORTANT : Les lampes dans le réfrigérateur et le congélateur

utilisent la technologie à DEL et n’ont pas besoin d’être

remplacées. Si les lampes ne s’allument pas lorsqu’on ouvre la

porte, appeler les numéros fournis pour obtenir de l’aide ou un

dépannage. Consulter le Guide de démarrage rapide pour les

coordonnées.

Le système d’éclairage pour cet appareil peut comprendre :

�Modules à DEL scellés

�Ampoules à DEL

�Ampoules incandescentes

�Ou une combinaison des susmentionnées.

Si une ampoule à DEL ne s’allume pas lorsque la porte du

réfrigérateur et/ou du congélateur est ouverte, la remplacer par

une ampoule semblable en procédant comme suit :

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Retirer le protège-ampoule (sur certains modèles).

�Retirer la visserie qui retient le protège-ampoules en place.

�Sommet du compartiment de réfrigérateur – Faire glisser

le protège-ampoule vers l’arrière du compartiment pour le

libérer de l’ensemble d’éclairage.

3. Toutes les ampoules pour appareils ménagers ne

conviendront pas à votre réfrigérateur. Remplacer les

ampoules grillées à l’aide d’ampoules pour appareil ménager

de la même taille, forme et puissance. Commander la pièce

no W10565137 (3,6 W).

REMARQUE : Certaines ampoules DEL de rechange ne sont

pas recommandées pour des environnements humides/

mouillés. Les compartiments de réfrigération et de congélation

sont considérés comme des environnements humides/

mouillés.

Si on utilise une marque d’ampoules DEL différente de celle

recommandée, lire et suivre toutes les instructions de

l’emballage des ampoules DEL avant de procéder à

l’installation.

4. Remettre en place le protège-ampoule (sur certains modèles)

en insérant les languettes situées sur le protège-ampoule

dans les trous de la doublure, de chaque côté de l’ensemble

d’éclairage. Faire glisser le protège-ampoule vers l’avant

jusqu’à ce qu’il s’emboîte.

REMARQUE : Afin d’éviter d’endommager le protège-

ampoule, ne pas le forcer au-delà du point de verrouillage.

5. Replacer la visserie qui retient le protège-ampoule en place.

6. Brancher le réfrigérateur ou reconnecter la source de courant

électrique.

Si une ampoule à incandescence ne s’allume pas lorsque la porte

du réfrigérateur ou du congélateur est ouverte, la remplacer par

une ampoule semblable en suivant la même procédure décrite ci-

dessus. Remplacer l’ampoule grillée par une ampoule à

incandescence de même taille, forme et puissance (maximum

40 W) conçues pour les appareils ménagers.

Éclairage du compartiment de congélation (sur

certains modèles)

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Ôter le protège-ampoule.

Sommet du compartiment de congélation – Faire glisser le

protège-ampoule vers l’arrière du compartiment pour le libérer

de l’ensemble d’éclairage.

3. Remplacer l’ampoule grillée par une ampoule pour appareils

électroménagers de 40 W maximum.

4. Réinstaller le protège-ampoule.

5. Brancher le réfrigérateur ou reconnecter la source de courant

électrique.

Tablettes du réfrigérateur

Informations importantes à propos des tablettes et des

couvercles en verre :

Ne pas nettoyer les tablettes ou les couvercles de verre avec de

l’eau tiède lorsqu’ils sont froids. Les tablettes et couvercles

peuvent se briser s’ils sont exposés à un changement de

températures ou impact soudain, tel qu’une chute. Le verre

trempé est conçu pour se briser en de multiples petits morceaux

de la taille de gravillons. Ceci est normal. Les tablettes en verre et

les couvercles sont lourds. Employer les deux mains lorsqu’on les

retire afin d’éviter de les faire tomber.

Les tablettes de réfrigérateur sont réglables pour s’adapter aux

besoins de rangement de l’utilisateur.

Afin de pouvoir trouver plus facilement l’article recherché, on peut

remiser ensemble des aliments semblables dans le réfrigérateur

et ajuster les tablettes pour les adapter aux différentes tailles

d’articles. Ceci réduira également la durée d’ouverture de la porte

du réfrigérateur et permettra d’économiser de l’énergie

Tablette repliable (sur certains modèles)

Pour replier la tablette repliable :

Replier la section repliable de la tablette en maintenant l’avant de

la tablette d’une main et en soulevant la partie centrale avant de la

tablette. Repousser ensuite la tablette vers l’arrière tout en

appuyant dessus jusqu’à ce qu’elle coulisse en dessous de la

section arrière de la tablette.

Pour réinstaller la tablette repliable :

Repositionner la section repliable de l’étagère en maintenant

l’avant de l’étagère d’une main tout en tirant sur le centre de

l’étagère jusqu’à ce que la section repliable soit de nouveau

complètement déployée.

Tablettes®® MicroEdge Glo (sur certains modèles)

Les crochets à l’arrière de la tablette doivent être complètement

insérés dans les supports de tablette pour assurer une

alimentation électrique adéquate.

Ne pas utiliser plus de deux tablettes munies d’éclairage par

dessous en même temps dans le réfrigérateur.

Ouverture et fermeture des portes

Il y a deux portes pour le compartiment de réfrigération. Les

portes peuvent être ouvertes et fermées séparément ou

ensemble. Sur certains modèles, il y a un mécanisme de

fermeture automatique évitant que la ou les portes ne restent

ouvertes de façon involontaire. Si la porte est ouverte à un angle

de 40° ou moins, elle se refermera automatiquement en douceur.

IMPORTANT : Si les portes ne se referment pas automatiquement

à un angle de 40° ou moins, voir la section « Charnière inférieure

de porte ».

Il y a sur la porte de gauche du réfrigérateur un joint à charnière

verticale.

�Lors de l’ouverture de la porte du côté gauche, le joint à

charnière se replie automatiquement vers l’intérieur pour qu’il

n’y ait pas d’interférence.

�Lorsque les deux portes sont fermées, le joint à charnière

assure automatiquement l’étanchéité entre les deux portes.

A. Joint à charnière

Le commutateur de la porte du réfrigérateur est situé dans le coin

supérieur gauche et le couvercle de la charnière de droite.

�Le commutateur de porte utilise un aimant pour capter

l’ouverture et la fermeture de la porte.

�S’assurer qu’aucun aimant ou appareil électronique (enceinte,

CoolVox,®etc.) ne se trouve à moins de 3 po (7,62 cm) du

couvre-charnière.

REMARQUE : L’éclairage et l’interface utilisateur (IU) intérieure

ne se mettent pas en marche s’il n’y a pas de détection

d’ouverture de porte.

A. Couvre-charnière

Précautions à prendre avant les

vacances ou le déménagement

Vacances

Si le réfrigérateur est laissé en marche pendant une

absence :

1. Consommer toutes les denrées périssables et congeler les

autres articles.

2. Si le réfrigérateur comporte une machine à glaçons

automatique et qu’il est raccordé à la source

d’approvisionnement en eau du domicile, fermer la source

d’approvisionnement en eau du réfrigérateur. Des dommages

matériels peuvent subvenir si l’alimentation en eau n’est pas

coupée.

3. Si votre machine à glaçons est automatique, éteindre la

machine à glaçons.

REMARQUE : Selon le modèle, soulever le bras de

commande métallique à la position Off (arrêt) (position

élevée), ou placer le commutateur sur Off (arrêt).

4. Vider le bac à glaçons.

Modèles avec fonction Vacation mode (mode vacances)

�Activer Vacation mode (mode vacances). Consulter le

« Guide de démarrage rapide » pour les détails.

REMARQUE : L’activation du mode « vacances » ne

désactive pas la machine à glaçons.

Si l’utilisateur choisit d’arrêter le réfrigérateur avant son

absence :

1. Enlever tous les aliments du réfrigérateur.

2. Si le réfrigérateur est équipé d’une machine à glaçons

automatique :

�Fermer l’approvisionnement en eau de la machine à

glaçons au moins un jour à l’avance.

�Lorsque la dernière quantité de glaçons est déposée,

soulever le bras de commande d’arrêt métallique à la

position Off (arrêt/position haute) ou placer le

commutateur sur Off (arrêt), selon le modèle.

3. Vider le bac à glaçons.

4. Éteindre la/les commande(s) de température. Voir le « Guide

de démarrage rapide ».

5. Nettoyer le réfrigérateur, l’essuyer et bien le sécher.

6. À l’aide d’un ruban adhésif, placer des blocs de caoutchouc

ou de bois dans la partie supérieure de chaque porte de façon

à ce qu’elles soient suffisamment ouvertes pour permettre à

l’air d’entrer et d’éviter l’accumulation d’odeur ou de

moisissure.

Déménagement

En cas de déménagement et de déplacement du réfrigérateur

dans une nouvelle habitation, suivre ces étapes pour préparer le

déménagement.

1. Si le réfrigérateur est équipé d’une machine à glaçons

automatique :

�Fermer l’approvisionnement en eau de la machine à

glaçons au moins un jour à l’avance.

�Débrancher la canalisation d’eau de l’arrière du

réfrigérateur.

�Lorsque la dernière quantité de glaçons est déposée,

soulever le bras de commande d’arrêt métallique à la

position Off (arrêt/position haute) ou placer le

commutateur sur Off (arrêt), selon le modèle.

2. Retirer tous les aliments du réfrigérateur et placer tous les

aliments congelés dans de la neige carbonique.

3. Vider le bac à glaçons.

4. Éteindre la/les commande(s) de température. Voir le « Guide

de démarrage rapide ».

5. Débrancher le réfrigérateur

6. Bien nettoyer, essuyer et sécher.

7. Retirer toutes les pièces amovibles, bien les envelopper et les

attacher ensemble avec du ruban adhésif pour qu’elles ne

bougent et ne s’entrechoquent pas durant le déménagement.

8. Selon le modèle, soulever l’avant du réfrigérateur pour qu’il

roule plus facilement ou soulever les pieds de nivellement

pour qu’ils n’égratignent pas le plancher. Voir les sections

« Ajustement des portes » ou « Fermeture et alignement des

portes ».

9. Fermer les portes à l’aide de ruban adhésif et fixer le cordon

d’alimentation à la partie arrière du réfrigérateur.

Une fois arrivé à votre nouveau domicile, remettre tout en place et

consulter la section des « Instructions d’installation » pour des

instructions sur la préparation de l’appareil. Aussi, si le

réfrigérateur comporte une machine à glaçons automatique, ne

pas oublier de rebrancher l’approvisionnement en eau au

réfrigérateur.

INSTRUCTIONS D’INSTALLATION

Déballage du réfrigérateur

AVERTISSEMENT

Risque de poids excessif

Utiliser deux personnes ou plus pour déplacer et installer

l’appareil.

Le non-respect de cette instruction peut causer une

blessure au dos ou d’autres blessures.

Livraison du réfrigérateur

�Une ouverture de porte minimum de 33 po (838 mm) est

nécessaire. Si l’ouverture est inférieure ou égale à 36 po

(914 mm), il faudra enlever les portes, tiroirs et charnières.

�Pousser le chariot avec le réfrigérateur de côté pour toutes les

ouvertures de porte.

Retrait des matériaux d’emballage

�Enlever tout résidu de ruban adhésif et de colle des surfaces

avant de mettre en marche votre tiroir de réfrigération. Frotter

une petite quantité de savon liquide à vaisselle sur l’adhésif

avec les doigts. Rincer à l’eau tiède et sécher.

�Ne pas utiliser d’instruments coupants, d’alcool à friction, de

liquides inflammables ou de nettoyants abrasifs pour enlever

le ruban adhésif ou la colle. Ces produits peuvent

endommager la surface du réfrigérateur. Pour plus de

renseignements, voir la section « Sécurité du réfrigérateur ».

�Éliminer/recycler tous les matériaux d’emballage.

Lors du déplacement du réfrigérateur :

Ce réfrigérateur est lourd. Lors du déplacement de ce

réfrigérateur pour un nettoyage ou un entretien, veiller à recouvrir

le plancher d’un carton ou panneau de fibre dur pour éviter de

l’endommager. Toujours tirer le réfrigérateur tout droit lors du

déplacement. Ne pas incliner le réfrigérateur d’un côté ou de

l’autre ni le « faire marcher » en essayant de le déplacer, car le sol

pourrait être endommagé.

Nettoyage avant utilisation

Après avoir enlevé tous les matériaux d’emballage, nettoyer

l’intérieur du réfrigérateur avant de l’utiliser. Voir les instructions

de nettoyage dans la section « Entretien du réfrigérateur ».

Informations importantes à propos des tablettes et des

couvercles en verre :

Ne pas nettoyer les tablettes ou les couvercles de verre avec de

l’eau tiède lorsqu’ils sont froids. Les tablettes et couvercles

peuvent se briser s’ils sont exposés à un changement de

températures ou impact soudain, tel qu’une chute. Le verre

trempé est conçu pour se briser en de multiples petits morceaux

de la taille de gravillons. Ceci est normal. Les tablettes en verre et

les couvercles sont lourds. Employer les deux mains lorsqu’on les

retire afin d’éviter de les faire tomber

A. Ampou-

B. Écrou

C. Tuyau en cuivre ou en

polyéthylène réticulé (vers le

réfrigérateur)

D. Canalisation d’alimentation en eau

du domicile (1/2 po minimum)

4. On est maintenant prêt à connecter le tuyau en cuivre ou en

polyéthylène réticulé au robinet d’arrêt. Utiliser une

canalisation en cuivre ou en polyéthylène réticulé de 1/4 po

(6,35 mm) (diamètre externe) pour raccorder le robinet d’arrêt

au réfrigérateur.

�S’assurer d’avoir la longueur nécessaire pour une

installation correcte. Il faut s’assurer que les deux

extrémités du tube en cuivre sont bien coupées à angle

droit.

�Installer la bague et l’écrou à compression sur le tuyau en

cuivre comme indiqué. (Le tuyau en polyéthylène réticulé

possède des viroles et écrous de compression déjà

installés.) Insérer l’extrémité du tuyau aussi profondément

que possible dans l’extrémité de sortie et à l’équerre.

Visser l’écrou de compression sur l’extrémité de sortie du

raccord à l’aide d’une clé à molette. Ne pas serrer

excessivement.

A. Virole de

compression

B. Écrou de

compression

C. Tuyau en cuivre ou en

polyéthylène réticulé

5. Placer l’extrémité libre de la canalisation dans un contenant

ou un évier et rétablir l’alimentation principale en eau pour

nettoyer le tuyau jusqu’à ce que l’eau soit limpide. Fermer le

robinet d’arrêt de la canalisation d’eau.

REMARQUE : Toujours vidanger le tuyau d’alimentation en

eau avant de faire le raccordement final sur l’entrée du robinet

pour éviter tout mauvais fonctionnement éventuel du robinet.

6. Courber le tuyau de cuivre ou de polyéthylène réticulé de

façon à le raccorder à l’arrivée de la canalisation d’eau située

à l’arrière de la caisse du réfrigérateur. Laisser une partie du

tube en cuivre ou de polyéthylène réticulé enroulée pour

permettre de dégager le réfrigérateur de l’armoire ou du mur

en cas de dépannage.

Raccordement au réfrigérateur

Selon le modèle, la canalisation d’eau peut être orientée de bas

en haut ou de haut en bas. Appliquer les instructions de

raccordement appropriées au modèle.

Style 1

1. Ôter le bouchon de plastique de l’orifice d’entrée d’eau.

Raccorder la canalisation en cuivre ou en polyéthylène

réticulé au robinet d’arrivée d’eau à l’aide d’un écrou et d’une

bague de compression, comme illustré. Serrer l’écrou de

compression. Ne pas serrer excessivement. Vérifier la solidité

du raccordement en tirant sur la canalisation en cuivre ou en

polyéthylène réticulé.

2. Créer une boucle de service avec la canalisation en cuivre.

Éviter de déformer le tube en l’enroulant. Fixer la canalisation

en cuivre ou en polyéthylène réticulé à la caisse du

réfrigérateur à l’aide d’un collier en P.

A. Tuyau en

cuivre ou en

polyéthylène

réticulé

B. Collier en P

C. Écrou de compression

D. Virole de compression

3. Ouvrir l’arrivée d’eau alimentant le réfrigérateur et vérifier

l’absence de fuites. Éliminer toute fuite détectée.

Style 2

1. Débrancher le réfrigérateur ou déconnecter la source de

courant électrique.

2. Retirer et jeter la courte pièce en plastique noire de l’extrémité

du point d’entrée de la canalisation d’eau.

3. Enfiler l’écrou sur l’extrémité du tuyau. Serrer l’écrou

manuellement. Ensuite, serrer deux tours de plus avec une

clé. Ne pas serrer excessivement.

REMARQUE : Pour éviter les vibrations, veiller à ce que les

tuyaux en cuivre ne soient pas en contact avec les parois

latérales de la machine à glaçons ou d’autres composants à

l’intérieur de la caisse.

A. Canalisation d’eau

du domicile

B. Écrou (à acheter)

C. Virole (à acheter)

D. Tuyau d’eau du

réfrigérateur

4. Installer la bride de la canalisation d’alimentation en eau bien

autour de la canalisation pour réduire la pression sur le

raccord.

5. Ouvrir le robinet d’arrêt.

6. Vérifier qu’il n’y a pas de fuites. Serrer tous les raccords (y

compris les raccords du robinet) ou les écrous qui présentent

des fuites.

Produktspecifikationer

Varumärke:	JennAir
Kategori:	kylskåp
Modell:	WRF954CIHZ

Behöver du hjälp?

Om du behöver hjälp med JennAir WRF954CIHZ ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

kylskåp JennAir Manualer

JennAir JKCPL181GL Bruksanvisning

8 Januari 2025

JennAir JBFFS42NHS Bruksanvisning

8 Januari 2025

JennAir JBZFR30IGX Bruksanvisning

7 Januari 2025

JennAir JUDFP242HX Bruksanvisning

7 Januari 2025

JennAir JBRFR36IGX Bruksanvisning

7 Januari 2025

JennAir JKCPR181GM Bruksanvisning

27 Oktober 2024

JennAir JFC2089BEM Bruksanvisning

27 Oktober 2024

JennAir MYSTIC18 Bruksanvisning

22 September 2024

JennAir MYSTIC24 Bruksanvisning

22 September 2024

JennAir MYSTIC30 Bruksanvisning

22 September 2024

kylskåp Manualer

Nyaste kylskåp Manualer

Zanussi 5634 Bruksanvisning

16 Januari 2025

AEG Electrolux 70398 DT Bruksanvisning

16 Januari 2025

Etna AK 1122 SA Bruksanvisning

16 Januari 2025

Indesit inbouw Koelvriescombinatie IN C 310 (SP-PT) Bruksanvisning

16 Januari 2025

AEG Electrolux S163TK48 Bruksanvisning

16 Januari 2025

AEG Electrolux U 96040-4 I Bruksanvisning

16 Januari 2025

Whirlpool ARG 10470 (A) Bruksanvisning

16 Januari 2025

Siemens KG 33VX97 Bruksanvisning

16 Januari 2025

Siemens KF 24 LA 50 Bruksanvisning

16 Januari 2025

Whirlpool ARG 955 Bruksanvisning

16 Januari 2025