Keurig K-Mini Bruksanvisning

Läs nedan 📖 manual på svenska för Keurig K-Mini (6 sidor) i kategorin kaffebryggare. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/6
Get the most from your
new Keurig® brewer
Use & Care Guide
Remove packing tape from brewer.
Pull plug and extend cord from cord
storage located at the back of the
brewer. Plug into a grounded outlet.
Press the power button. The power
button will illuminate.
Add 1 cup (8oz) of water into
a mug. Lift the water reservoir
lid and pour the water into the
reservoir. Do not fill past the MAX
or below the MIN fill lines. Lower
the lid and place your mug on the
drip tray.
NOTE: Do not use distilled water.
Lift and lower the handle. Do not
insert a K-Cup® pod. The brew
indicator light will flash to indicate
that the brewer is ready.
Press the brew button. The brew
indicator light will illuminate solid,
then begin to pulse while the brewer
is heating. After about 2 minutes, the
brew indicator light will illuminate
solid again and the water will begin
to dispense. Pour the hot water into
the sink.
The one-time setup process is now
complete and you are ready to brew!
1
3
5
2
4
6
Before You Brew
Add desired amount of water
into a mug (6oz minimum, 12oz
maximum). Lift the water reservoir
lid and pour the water into the
reservoir. Do not fill past the MAX or
below the MIN fill lines. Lower the lid
and place your mug on the drip tray.
Lift the handle. Place a K-Cup® pod in
the K-Cup® pod holder. Lower the handle
completely to close the lid. The brew
indicator light will flash to indicate that
the brewer is ready. Do not remove the
foil lid on the K-Cup® pod.
High Altitude Brewing: While holding the brewer
handle up, push down slowly on the K-Cup® pod
in the pod holder until the bottom of the
K-Cup® pod is punctured by the exit needle.
Brew Button
Plug & Power Fill & Place
Lift & Lower Cleansing Brew
Fill & Place Mug
7
Press the brew button. The brew
indicator light will illuminate solid,
then begin to pulse while the
brewer is heating. After about 2
minutes, the brew indicator light
will illuminate solid again and the
beverage will begin to dispense.
Brewing is complete when the
brew indicator light is no longer
illuminated. When complete, lift the
handle and dispose of the used K-Cu pod.
CAUTION: While brewing, there is extremely hot water in the K-Cup® pod holder. To avoid injury, do
not lift the handle during the brewing process.
Brew Button
Brew & Enjoy!
Lift & Place Pod
Brewer Features
Auto Off: Automatically turns your brewer off 90 seconds after the last brew
for energy savings.
Cord Storage: Makes transporting your brewer convenient and keeps
countertops tidy.
Travel Mug Friendly: Remove the drip tray to accomodate a travel mug.
Brew Your First Cup
Caring for your Brewer
K-Cup® Pod Holder
To remove the K-Cup® pod holder from
the brewer, lift the handle and grasp
the top of the K-Cup® pod holder
with one hand while pushing up on
the bottom of the K-Cup® pod holder
from underneath with the other until
it releases. After cleaning, align the
K-Cup® pod holder with the opening
using the two front ribs as a guide
and snap into place from the top.
Funnel
Washing the funnel ensures a fresh
beverage experience. The funnel
should be washed regularly and can
be removed from the K-Cup® pod
holder by pulling on it until it pops off.
To replace it, orient the snaps to the
indent and just snap it back onto the
K-Cup® pod holder.
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
The water reservoir should be
cleaned periodically by wiping the
inside of the reservoir and underside
of the lid with a damp, non-abrasive,
lint free cloth. Do not dry the inside
of the water reservoir with a cloth as
lint may remain. Allow the reservoir
to dry completely.
Exit Needle
Remove the pod holder assembly
and detach the funnel. Locate the
exit needle on the inside bottom
of the K-Cup® pod holder. Insert a
straightened paper clip into the exit
needle to loosen any coffee grounds.
Entrance Needle
Lift the brewer handle and locate the entrance needle on the
underside of the lid. To clean both holes in the needle, hold
the brewer handle in the upward position and with your other
hand, carefully insert a straightened paper clip into both
holes. Gently move it around to loosen any coffee grounds.
Lower the handle completely and run two water-only brew
cycles. Do not insert a K-Cup® pod.
TIP: Refer to support.keurig.com for video instructions on cleaning the entrance/exit needles.
Brewer Exterior
Keep your Keurig® brewer looking its
best by cleaning the exterior from
time to time. Just clean with a damp,
soapy, lint-free, non-abrasive cloth.
Never immerse the brewer in water or
other liquids.
Drip Tray
The drip tray can hold up to 8 ounces
of overflow and should be emptied
and cleaned occasionally. To remove,
slide it toward you, keeping it level to
avoid spilling. Rinse and clean with a
damp, soapy, lint-free, non-abrasive
cloth.
Water Reservoir
CAUTION: There are sharp needles that puncture the K-Cup® pod above the K-Cup® pod holder and in the
bottom of the K-Cup® pod holder. To avoid risk of injury, do not put your fingers in the K-Cup® pod holder.
NOTE: Always remove and dispose of the used K-Cup® pod after brewing.

Produktspecifikationer

Varumärke: Keurig
Kategori: kaffebryggare
Modell: K-Mini

Behöver du hjälp?

Om du behöver hjälp med Keurig K-Mini ställ en fråga nedan och andra användare kommer att svara dig




kaffebryggare Keurig Manualer

kaffebryggare Manualer

Nyaste kaffebryggare Manualer