Kicker Solo-Baric VS10L7 Bruksanvisning

Kicker Subwoofer Solo-Baric VS10L7

Läs nedan 📖 manual på svenska för Kicker Solo-Baric VS10L7 (4 sidor) i kategorin Subwoofer. Denna guide var användbar för 16 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
L7
SOLO-BARICSUBWOOFERENCLOSURE
VS , VS , TS12L7 10L7 10L7
©2007 Stillwater Designs
CheckTheLoad
The Solo-Baric subwoofer enclosures are internally wired for a 2 or 4 ohm load at the
speaker-wire connection terminal. Please refer to this terminal or the box packaging for your
enclosure’s specific impedance. Check to see if your amplifier is optimized to drive this load.
VSVented
The VS Series vented enclosures combine KICKER’s award winning Solo-Baric subwoofers
with computer-modeled and human fine-tuned enclosures to offer a level of bass
performance never before thought possible from a commercially available, ready-to-install
subwoofer system. The VS Series enclosures are available with a pre-loaded 10 or 12 inch
Solo-Baric L7.
The location and orientation of your enclosure will affect the quality and quantity of the
bass. Designed for use in SUV and sedan type vehicles, these enclosures offer you several
mounting options. The vent opening in these enclosures can not be obstructed. At some
frequencies most of the bass will come out of the vent. Therefore we recommend you leave
at least four inches (10cm) of clear space around the vent.
If the enclosure is to be mounted all the way in the back of the vehicle, it works best to
point the woofer toward the front of the vehicle. Conversely, if the enclosure is going to be
mounted closer to the back seat, pointing the woofer toward the rear of the vehicle will give
you the best results. These guidelines pertain to enclosures mounted in the vehicle as
outlined in Figure 1.
If it is more convenient to mount the enclosure along a side wall, put the enclosure on the
left side of the vehicle as outlined in Figure 2. This orientation will make the vent point
toward the rear of the vehicle and will produce the most low bass output. Remember to
leave at least four inches (10cm) of room between the enclosure and the back of the
vehicle.
After determining the best mounting position, carefully check the areas where the mounting
brackets will be placed. Make sure the mounting screws will not puncture the gas tank,
brake lines, wiring, or interfere with any mechanical parts on the underside of the mounting
surface. Turn the enclosure upside-down, pre-drill the holes using a 7/64” (2.5mm) bit and
attach the four mounting brackets to the bottom of the enclosure using the supplied smaller
C N NO FIGURATIO
SOLO-BARICSUBWOOFERENCLOSURE
VS12L7 / VS10L7 / TS10L7
Models:
Solo-BaricL7Subwoofer
EnclosureOwner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Enclosure Model Number:
Enclosure Serial Number:
_________________________
_________________________
_________________________
_________________________
Please allow two weeks of break-in time for the subwoofer to reach optimum bass performance.
23
INSTALLATION
A t least 4”
(10cm) from
t eh vent
F u ig re 2
R ,ear nting mou
s apeaker f ces
f o h cr nt of ve i le
F o ,r nt mounting
s apeaker f ces
rear le of ve ih c
F or nt of
Ve ih cle
A t least 4” (10cm)
f hrom t e vent
A t least 4” (10cm)
f hrom t e vent
F uig re 1
screws. Each bracket must be positioned so the rounded end protrudes approximately
3/4" (2cm) from under the cabinet to allow a screw to easily pass through the bracket,
securing the enclosure to the vehicle. See Figure 4.
Plug your subwoofer speaker wire into the terminals, using the red connector as positive
and the black connector as negative. Hook the other end of the wire to your subwoofer
amplifier in accordance with its owner's manual. With the enclosure right side up, securely
attach the enclosure to the vehicle with the supplied larger screws. If the supplied hardware
is not applicable to your installation, some other means of securely attaching the enclosure
to the vehicle must be used.
L f de t Si e
mounting,
s apeaker f ces
opposite side
of ve ih cle
F or nt of
Ve ih cle
4 5
PERFORMANCE
INSTALLATION
Measurements are based on the 4 ohm enclosures. Note: The use of a subsonic filter will significantly increase the power handling.
The power handling specifications in these charts are calculated using a 25Hz, 24dB per octave subsonic filter.
*Power Handling Watts RMS without subsonic filter: VS10L7-200, VS12L7-200, TS10L7-600
SOLO-BARICSUBWOOFERENCLOSURE
TSVented
The TS Series vented enclosure combines KICKER’s award winning Solo-Baric subwoofers
with computer-modeled and human fine-tuned enclosures to offer a level of bass
performance never before thought possible from a commercially available, ready-to-install
subwoofer system. The TS Series enclosure is available with a pre-loaded 10 inch
Solo-Baric L7.
The Kicker TS Series enclosure is designed to fit behind the seat of a pickup truck, coupe
or wherever space is limited. This design is engineered to provide the best bass response
when firing into the back of the seat.
Plug your subwoofer speaker wire into the terminals, using the red connector as positive
and the black connector as negative. Hook the other end of the wire to your subwoofer
amplifier in accordance with its owner's manual.
Seat
F dloor Boar
D r eoo Fram
F uig re 3
Model:
Nominal Impedance [Zn], ohm [per enclosure]
Power Handling* Watts, Peak (RMS)
Enclosure Top Surface Depth, in (cm)
Enclosure Bottom Surface Depth, in (cm)
Enclosure Height, in (cm)
Enclosure Width, in (cm)
VS12L7
2 or 4
1500 (750)
14 11/16 (37.2)
18 (45.7)
16 (40.6)
18 3/4 (47.5)
VS10L7
2 or 4
1200 (600)
13 (33.1)
16 7/16 (41.7)
14 (35.6)
17 (43.3)
TS10L7
2 or 4
1500 (750)
6 11/16 (16.9)
10 (25.4)
15 (38.1)
21 1/2 (54.6)
Performance
Model:
Nominal Impedance [Zn], ohm [per enclosure]
Power Handling* Watts, Peak (RMS)
Enclosure Top Surface Depth, in (cm)
Enclosure Bottom Surface Depth, in (cm)
Enclosure Height, in (cm)
Enclosure Width, in (cm)
Mou ck o nt Bra ets t t eh bottom of t e l sh enc o ure using
t e s s s t eh upp d lie maller crews Se atta. curely ch h
en le wit lie largerc o ul s re h h cto t e ve i h t e sh upp d cs rews.
F uig re 4
SafetyWarning
To avoid potential injury, or possible death, from forward movement of the enclosure during
abrupt stops or accidents, the enclosure must be properly installed and securely fastened to
your vehicle. You are solely responsible for securely fastening the enclosure in your vehicle.

Produktspecifikationer

Varumärke: Kicker
Kategori: Subwoofer
Modell: Solo-Baric VS10L7

Behöver du hjälp?

Om du behöver hjälp med Kicker Solo-Baric VS10L7 ställ en fråga nedan och andra användare kommer att svara dig


Subwoofer Kicker Manualer

Kicker

Kicker 51MWF104 Bruksanvisning

14 Januari 2025
Kicker

Kicker 51MWF124 Bruksanvisning

14 Januari 2025
Kicker

Kicker 51MWE104 Bruksanvisning

10 Januari 2025
Kicker

Kicker 51MWE124 Bruksanvisning

10 Januari 2025
Kicker

Kicker 48CWR154 Bruksanvisning

8 Januari 2025
Kicker

Kicker 50CVX154 Bruksanvisning

2 Januari 2025
Kicker

Kicker 50CVX124 Bruksanvisning

2 Januari 2025
Kicker

Kicker 51CWQ102 Bruksanvisning

26 September 2024
Kicker

Kicker 51CWQ122 Bruksanvisning

26 September 2024
Kicker

Kicker 43C84 Bruksanvisning

26 September 2024

Subwoofer Manualer

Nyaste Subwoofer Manualer

Sonance

Sonance Bandpass BPS6 Bruksanvisning

8 Januari 2025
OSD Audio

OSD Audio GLS8 Bruksanvisning

6 Januari 2025
Audibax

Audibax DSP18s Bruksanvisning

6 Januari 2025
Audibax

Audibax DSP12s Bruksanvisning

6 Januari 2025
Audibax

Audibax Manhattan 18S Bruksanvisning

6 Januari 2025
Ecler

Ecler LABI1-SB18p Bruksanvisning

6 Januari 2025
OSD Audio

OSD Audio BOM4.1.2 Bruksanvisning

5 Januari 2025
Kenwood

Kenwood Excelon XM1041BL Bruksanvisning

5 Januari 2025
REL Acoustics

REL Acoustics T/9x SE Bruksanvisning

5 Januari 2025
James

James 81ST4 Bruksanvisning

5 Januari 2025