Kicker SubStage SF150S09 Bruksanvisning

Kicker Subwoofer SubStage SF150S09

Läs nedan 📖 manual på svenska för Kicker SubStage SF150S09 (9 sidor) i kategorin Subwoofer. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/9
1
SF150S09
Designed for 2009 and newer Ford® F-150 Super-Cab vehicles
Subwoofer Assembly
Subwoofer Power Harness
Subwoofer Body
Harness
25A Fuse
Wire Ties x6
Foam Strips
M6 Speed Clips x3
Adhesive Covers x3
M6 Bolts x3
M8 Bolts x3
M8 Nut Inserts p1-x3
(Requires Nut Insert Tool)
Wire Taps x2
Adapter Harness
©2012 Stillwater Designs
SF150S09-A2-20121213
2
Power Wire Routing
1. Open the hood, disconnect the negative battery cable.
2. Find the fuse box in the engine compartment and open the cover.
3. Remove the nut on the accessory lug, connect the power wire and retighten the nut. Torque to 9Nm.
Fig. 1
4. Route the power wire across the radiator support and toward the grommet on the driver’s side of the
rewall. Fig. 2
5. Make a small incision in the rubber grommet and pass the power wire into the cabin.
6. Install the black connector on the end of the power harness inside the cabin. The black connector should
have a block out plug installed in one side to prevent the power wire from being inserted into the wrong
position in the connector.
7. Connect the black two-pin connector of the power wire to the corresponding connector of the subwoofer
harness.
8. Remove the driver’s side threshold panel along the bottom of the front and rear door opening. Fig. 3
9. Pull back the rubber door molding and then pull back on the kick panel to remove it. Fig. 3
10. Connect the black ground wire of the subwoofer harness to the factory ground point in the drivers side
kick panel. Torque to 9Nm. Fig. 4
11. Route the subwoofer harness along the door opening and toward the rear of the cab.
Subwoofer Input Connection without Optional Amplifi er
12. Connect the adaptor harness to the white two pin connector of the subwoofer body harness.
13. Find the twisted pair of wires in the driver’s side kick panel that are solid white and white with a brown
stripe.
Connect
Power Wire
Here
Secure
Harness
Here Fig. 1
Grommet
Fig. 2
Fig. 3
Fig. 4
Connect
black
ground
wire of
subwoofer
harness
3
14. Tap the wires using the supplied wire taps. Fig. 5
15. Connect the brown wire of the adaptor harness to the solid white wire. Connect the green wire of the
adaptor harness to the white/brown wire. Fig. 6
Subwoofer Input Connection with Optional Amplifi er
16. Connect the white two pin connector of the amplifi er harness to the corresponding connector of the
subwoofer harness.
Jack Relocation
17. Remove the three bolts securing the jack mounting plate.
18. Move the plate and jack to the passenger’s side rear seat area and push it back until the tool bag touch-
es the front of the seat frames. Make sure the jack mounting plate is oriented the same way it was originally
with two mounting holes toward the rear of the truck and one toward the front. Fig. 7
19. Measure over exactly seven inches from the inside of the seat frame to the edge of the jack mounting
plate. It is important that this measurement be accurate. Mark the three mounting holes with a marker and
then drill a 1/8 inch pilot hole in the center of each of the three mounting holes. Fig. 8
20. Remove the jack and mounting plate and tape the paper template to the carpet lining up the three marks
with the corresponding markings on the template. Fig. 9
21. Cut the carpet along all the dotted lines on the template. When you are nished you will have two aps,
one large and one small. Pull back the two fl aps and cut away all the carpet insulation beneath. Fig. 10
Fig. 5
Fig. 6
Fig. 7
7 inches
Fig. 8

Produktspecifikationer

Varumärke: Kicker
Kategori: Subwoofer
Modell: SubStage SF150S09

Behöver du hjälp?

Om du behöver hjälp med Kicker SubStage SF150S09 ställ en fråga nedan och andra användare kommer att svara dig




Subwoofer Kicker Manualer

Subwoofer Manualer

Nyaste Subwoofer Manualer