Kyoritsu KEW 5020 Bruksanvisning

Läs nedan 📖 manual på svenska för Kyoritsu KEW 5020 (56 sidor) i kategorin Mätutrustning. Denna guide var användbar för 15 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/56
INSTRUCTION MANUAL
KEW LOGGER SERIES
Current Logger KEW 5010
Current&Voltage Logger
KEW 5020
Current / Voltage Measurement & Recording
Introduction
Thank you for purchasing KEW LOGGER 5010/5020.
Follow the procedure below and set time on the instrument before use.
  1) Install the KEW LOG SOFT 2 and the USB Driver according to the
instructions written in the Install Manual for KEW LOG Soft 2.
  2) Run KEW LOG SOFT 2 once install is completed. (Refer to
4. Start
KEW LOG SOFT 2
in the Install Manual.)
  3) Confirm that the LOGGER and a PC is firmly connected with a USB
Cable and click
Time Synchronizing
.
  4) Confirm that the Logger connected with the PC is listed on the
List of detected loggers
. (The USB Driver might not be installed
correctly when a message
No Logger is detected.
is displayed.
Refer to the backside of the
Cautions for installing USB Driver
install
or
6. Trouble shooting
of the Install Manual and re-install
the USB Driver.)
  5) Click
Time Synchronizing
Button while the LOGGER is powered on
and checks are marked in the box for each connected LOGGER to
set time.
◦
Read this manual and do your desirable settings. (Setting should be done
by using
KEW LOG Soft 2
. Settings for some Recording modes can be
done on the LOGGER.
◦
Read through
1. Safety Warnings
in this manual before using the
LOGGER in order to ensure safe operation of the instrument.
Contents
1. Safety warnings ………………………………………………………… 1
2. Features …………………………………………………………………
4
3. Instrument layout ………………………………………………………
5
3-1) Panel ……………………………………………………………… 5
3-2) LCD …………………………………………………………………
5
3-3) Displayed message ……………………………………………… 7
3-4) Function of Button ………………………………………………… 8
3-5) Range/ Filter function …………………………………………… 9
4. Recording procedures ………………………………………………… 10
Step1: Start-up ……………………………………………………… 11
Step2: Confirmation of set value …………………………………… 12
Step3: Preparation before a recording ……………………………… 13
Step4: Start of recording …………………………………………… 15
Step5: Stop of recording
……………………………………………… 17
5. Recording modes and conditions
……………………………………… 18
Normal recording mode ……………………………………………… 19
Trigger recording mode ……………………………………………… 22
Capture recording mode ……………………………………………… 24
Power Quality Analysis mode (only 5020) …………………………… 24
6. Recording modes ……………………………………………………… 25
Flashing Detection LED
………………………………………………… 28
7. Simplified Power Integration Function
………………………………… 31
(available on KEW LOG Soft 2)
8. Other settings (Setting2) ……………………………………………… 34
9. Confirmation of recorded data (CALL)
………………………………… 39
10. Data transfer to PC …………………………………………………… 43
11. Battery replacement
…………………………………………………… 45
12. Auto-power off Function & External power supply …………………… 46
13.Trouble-shooting
………………………………………………………… 47
14.Specification …………………………………………………………… 49

Produktspecifikationer

Varumärke: Kyoritsu
Kategori: Mätutrustning
Modell: KEW 5020

Behöver du hjälp?

Om du behöver hjälp med Kyoritsu KEW 5020 ställ en fråga nedan och andra användare kommer att svara dig




Mätutrustning Kyoritsu Manualer

Mätutrustning Manualer

Nyaste Mätutrustning Manualer