Lab Gruppen E 10:4 Bruksanvisning

Lab Gruppen mottagare E 10:4

Läs nedan 📖 manual på svenska för Lab Gruppen E 10:4 (2 sidor) i kategorin mottagare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
▸High power density – 4 x 250 W in 1U
▸Certied Energy Star compliant
▸Flexible – IntelliDrive delivers comparable power per channel at
70 V or Low-Z (4, 8 and 16 ohms)
▸Asymmetric loading – Allows “mixing and matching” of loads
with different impedances to maximize system efciency and
inventory utilization
▸IDEEA™ output state based on patented Class D variant
▸Exceptionally low lifetime operating costs
▸High efciency – Extremely low power consumption and
heat output
▸Auto-standby function – Power consumption < 1 W in
standby mode
▸RSL Switch – Innovative circuit senses rail voltage and optimizes
output for instantaneous load conditions
▸Efcient cooling – Dual temperature-controlled fans
▸Comprehensive circuit protection and fault indication
Small in size, huge in benefits
Building on Lab.gruppen’s touring reputation for sonic excellence
and rock-solid durability, E Series brings a competitive edge to the
installation market by adding ultra-compact size, high operating
efciency, output conguration exibility, and an unprecedented
cost-benet ratio.
At the heart of E Series is Lab.gruppen’s IDEEA (IntelliDrive Energy
Efcient Amplier) technology. Based around a patented Class D
variant output stage, IDEEA produces high power levels with very
low distortion while drawing minimal mains current.
Lab.gruppen’s proprietary Rail Sensing Limiter (RSL™), also
exclusive to E Series, greatly reduces signal clipping to ensure high
quality audio output at all times. User congurable for Hi-Z
(70 V) or Lo-Z, RSL senses rail voltages and optimizes each output
for instantaneous load conditions. RSL settings also facilitate
asymmetric loading of the channels to optimize performance and
efciency. Total available output power can be allocated among the
channels as required by the application. This makes it possible, for
example, to drive a small sub on one channel, a number of 70 V
ceiling loudspeakers on the second channel, and a pair of full-range
low impedance loudspeakers on the two remaining channels.
Lab.gruppen performance with Energy Star compliance
Lab.gruppen’s IDEEA architecture secures full Energy Star compliance
by combining net operating efciency of greater than 80% with an
auto-power-down feature. After 20 minutes with no input signal, the
amplier automatically switches to standby mode – with consumption
of less than 1 W – and switches back on when an input signal returns.
GPIO facilities enable third-party systems to remotely control and
monitor power state via contact closure.
• Bars&restaurants
• Retailoutlets
• Malls
• Hotels&ballrooms
• Conferencecenters
• Museums&galleries
• Housesofworship
• Themeparkinstallations
• Educationalestablishments
• Auditoriums
• Performingartscenters
• Conventioncenters
• Transporthubs
Applications
W W W . L A B G R U P P E N . C O M
E Series, built around Lab.gruppen’s eco-friendly IDEEA: IntelliDrive Energy Efficient Amplifier
Specically designed for greater sustainability through “greener” commercial installations, E Series incorporates the latest advances in
Lab.gruppen quality and durability into a complete line of compact (1U) and highly cost-effective two- and four-channel ampliers.
Technical Data
E Series: Dedicated Installation Amplifiers
E 10:4
Specifications E 10:4
Item no. TDS-E10:4_V1 - 26.01.16
General
Number of channels 4
Total output all channels driven 1000 W
Peak output voltage per channel 100 V / 70 Vrms
Max. output current 14 Arms
Max.OutputPower(all ch.’s driven)
2 ohms N.R.
4 ohms 250 W
8 ohms 250 W
16 ohms 250 W (requires the “70 V” mode for the RSL, “Lo-Z” gives 125 W)
70 V 250 W
100 V Can deliver 250 W to a 100 V load tapped at 500 W
Performance
THD 20 Hz - 20 kHz for 1 W <0.1%
THD at 1 kHz and 1 dB below clipping <0.05%
Signal To Noise Ratio >112 dBA
Channel separation (Crosstalk) at 1 kHz >70 dB
Frequency response 2 Hz - 40 kHz
Input impedance 20 kOhm
Common Mode Rejection (CMR) 50 dB
Output impedance 25 mOhm
Gain,SensitivityandLimiters
Limit and gain switch defining limit and gain (per channel) 2 pos: Lo-Z and 70 V
VPL for 70 V mode 100 V
VPL for Lo-Z mode 63.2 V
Sensitivity for stated power into 8 Ohm in Lo-Z mode 4 dBu
Sensitivity for 70.7 V out in 70 V mode 4 dBu
Sensitivity for stated power into 4 Ohm in Lo-Z mode 1 dBu
Sensitivity for stated power into 16 Ohm in 70 V mode 3 dBu
Gain in 70 V mode 35.2 dB
Gain in Lo-Z mode 31.2 dB
Level adjustment (per channel) Rear panel potentiometer, from -inf to 0 dB
Connectorsandswitches
Input connectors (per ch.) 3-pin detachable screw terminals, electronically balanced
Output connectors (per ch.) 2-pin detachable screw terminals
High passlter Fixed at 50 Hz, switchable per channel
Power control Can be used to go between standby and ON
GPI (power control input) Contact closure type, 2-pin detachable screw terminal, controls the power state
GPO (power state output) Contact closure type, 2-pin detachable screw terminal, for external monitoring of the power state
Cooling Two fans, front to rear airflow, temperature controlled speed
Power
Nominal voltage 100 - 240 VAC
Operating voltage 85 - 265 VAC
Standby consumption <1 W
Mains connector IEC inlet
Dimensions W: 483 mm (19”), H: 44 mm (1 U), D: 381 mm (15”)
Weight 6.2 kg (13.7 lbs)
Finish Dark grey aluminium front and black steel chassis
Approvals CE, ANSI/UL 60065 (ETL), CSA, CCC, PSE, Energy Star
All specifications are subject to change without notice.
W W W . L A B G R U P P E N . C O M

Produktspecifikationer

Varumärke: Lab Gruppen
Kategori: mottagare
Modell: E 10:4

Behöver du hjälp?

Om du behöver hjälp med Lab Gruppen E 10:4 ställ en fråga nedan och andra användare kommer att svara dig


mottagare Lab Gruppen Manualer

Lab Gruppen

Lab Gruppen PLM 8K44 BP Bruksanvisning

23 September 2024
Lab Gruppen

Lab Gruppen PLM 8K44 SP Bruksanvisning

23 September 2024
Lab Gruppen

Lab Gruppen fP 2200 Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen FP 10000Q Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen CA1201 Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen CRC-VEU-BK Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen CM82 Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen CA602 Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen C48:4 Bruksanvisning

15 September 2024
Lab Gruppen

Lab Gruppen C88:4 Bruksanvisning

15 September 2024

mottagare Manualer

Nyaste mottagare Manualer

Speco Technologies

Speco Technologies PBM120AT Bruksanvisning

27 Oktober 2024
Fosi Audio

Fosi Audio V3 Bruksanvisning

26 Oktober 2024
Jensen

Jensen CAR710-4BC Bruksanvisning

26 Oktober 2024
Onkyo

Onkyo TX-RZ830 Bruksanvisning

24 Oktober 2024
Pioneer

Pioneer VSX-1122K Bruksanvisning

22 Oktober 2024
NAD

NAD C 355BEE Bruksanvisning

21 Oktober 2024
Yamaha

Yamaha HTR-5072 Bruksanvisning

21 Oktober 2024
Yamaha

Yamaha RX-A810 Bruksanvisning

20 Oktober 2024
Sherwood

Sherwood R-607 Bruksanvisning

20 Oktober 2024
Denon

Denon AVC-S660H Bruksanvisning

19 Oktober 2024