Liftmaster 050ACTBLKMC Bruksanvisning

Liftmaster Inte kategoriserad 050ACTBLKMC

Läs nedan 📖 manual på svenska för Liftmaster 050ACTBLKMC (13 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/13

DANGER PELIGRO•

132C2280- 3D

TO ERASE ALL

RECEIVER CODES

1. Pre ss and HO LD

re ce iver o range

ERASE but t o n

6 se co nds. Ind ica t o r

light will t urn O N.

2. Re le ase butt on

whe n light t urns O FF.

CANADA:

PART : DE PIEZA:NO. NO.

DATE:

T HE CHAMBER LAIN

GRO UP, INC ., US A

Ens am blad o e n Méxic o

Ass em bled in Mexi co

ELIMINACIÓN DE

TODOS LOS CÓDIG OS DEL

RECEP T OR

1. MANTENG A PRES IONADO

e l bo t ón nar an ja " ERASE "

de l rec ept or dura nt e 6

se gundo s. La luz de l

indica dor s e enc ende rá.

2. Sue lte el bo tó n cu ando la

luz se apa gue .

DANGER PELIGRO•

132C2280-3D

TO ERASE A LL RECEIV ER CODE S

1.Pressand HOLD

receivero rang e

ERASE b u tto n

6 Ind icato rseco nd s.lig h t wi ll turn ON.

2.Releasebu tto n

when lig h t tu rns OF F.

CANADA:

P : ARTN O. N O.DEPIEZA:

DATE:

THE C H A M BER LAI N

GROU P, I N C ., U SA

EnsambladoenMéxico

Assembled Mexico i n

ELIM INAC IÓN DE TODOSLO S CÓD IGOS D EL

RECEP TOR

1. P RES IONADO MANTENGA

el b o tó n naranja "ERASE "

d el receptor 6 d u rante segund o s. La lu z d el

ind i cado r seencend erá.

2. el cuand o Suelte b o tó n la

luz seapague.

Before you begin

Installation

RECEIVER LOGIC BOARD REPLACEMENT

Model 050ACTWFMC

1.2 To maintain your warranty, place the

provided label over the existing label

on the end panel of the garage door

opener.

1.1 Remove the light lens by pulling the

top sides of the light lens and rotate the

light lens down. Squeeze the light lens

clips to remove lens from end panel.

Your garage door opener has an internal gateway located on the receiver logic board. After installing the new receiver logic board, use the myQ

® serial number found on the provided label to add your

garage door opener to your myQ account. The products illustrated in the instructions are for reference. Your product may look different.

1.3 Disconnect power to the garage door

opener.

Remove the receiver logic board

2.1 Disconnect the wires from the quick-connect terminals ( ). A

Remove the receiver logic board end panel from the garage

door opener.

2.2 Unplug the wire harnesses from the receiver logic

board. You may need needle-nosed pliers to remove

the harnesses.

To prevent possible SERIOUS INJURY or

DEATH:

• Disconnect ALL electric and battery

power BEFORE performing ANY service

or maintenance.

To prevent damage to the receiver/logic

board, DO NOT touch printed circuit board

of replacement receiver/logic board during

installation.

ALWAYS wear protective gloves and eye

protection when changing the battery or

working around the battery compartment.

To insert or remove

the wires from the

terminal, push in the

tab with a

screwdriver tip.

Red

White

Grey

2.3 Remove the receiver

logic board from the

end panel by removing

the 2 screws and

releasing the 2 clips.

Screws

Wire clip

Clips

AVERTISSEMENT : Ce produit peut vous exposer à des produits chimiques, dont le plomb, qui sont reconnus par l’État de Californie

comme provoquant le cancer, des malformations congénitales ou d’autres problèmes de reproduction. Pour en savoir plus, visitez

www.P65Warnings.ca.gov.

Install new receiver logic board

3.3 Reinsert the wires.

Door control wires:

• white wire into the white terminal.

• white/red wire into the red terminal.

Safety sensor wires:

• white wires into the white terminal.

• white/black wires into the

grey terminal.

NOTE: A test of the safety reverse system is necessary for safe operation.

To insert or remove the

wires from the terminal,

push in the tab with a

screwdriver tip.

Programming

1.1 Press and release the Learn button on the garage door opener. The Learn indicator light

will glow steadily for 30 seconds.

1.2 Within 30 seconds, press and hold the

button on the remote control.

1.3 Release the button when the garage

door opener light blinks. It has learned

the code. If light bulbs are not installed,

two clicks will be heard.

Program a remote control using the learn button

Learn

Indicator

Light

Yellow Learn

Button

3.4 Install the light lens by aligning with

the hinges and snapping into place.

Reconnect power.

NOTE: When installing the light lens, ensure the antenna

wires are hanging straight down.

Red

White

Grey

To program the Wi-Fi garage door opener to your network refer to your owner’s manual.

3.2 Insert the antenna wires through

the holes in the end panel. Snap the

receiver logic board into place on the

end panel and fasten with screws.

NOTE: Some models

will require the short

antenna wire to be

placed in the traps of

the end panel.

Antenna wires

Antenna

wires

3.1 Connect the wire harnesses to the

new receiver logic board. When

reconnecting the wire harness, be sure

the tabs on the wire harness are facing

the end panel, not the logic board.

Logic Board

Wire Clip

End Panel

Wire

Harness

Tabs

NOTE: If your logic board

has a wire clip, use the

wire clip to hold wires to

the logic board.

Program the travel

Without a properly installed safety reversal

system, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by a

closing garage door.

• Incorrect adjustment of garage door travel

limits will interfere with proper operation

of safety reversal system.

• After ANY adjustments are made, the

safety reversal system MUST be tested.

Door MUST reverse on contact with 1-1/2"

(3.8 cm) high object (or 2x4 laid ﬂat) on

ﬂoor

While programming the travel, the UP and

DOWN buttons can be used to move the door

as needed. The Safety Reversing Sensors

will be disconnected during the Program the

Travel process. During the Automatic Force

Setup the door will automatically open and

close.

1.1 Press and hold the Adjustment Button

until the UP Button begins to and/ash

or a beep is heard.

The Safety Reversing Sensors will be

disconnected during the Program Travel the

process.

1.2 Press and hold the UP until the Button

door is in desired UP position.the

1.3 Once the door is in the desired

UP position press and release the

Adjustment door Button. The garage

opener lights will ﬂash twice the and

DOWN Button will begin to ash.

1.4 Press and hold the button DOWN

until the is in the desired door DOWN

position.

Once both the up and down positions have been manually set, the Safety Reversing Sensors

will reconnect and become operational. Then, the opener will enter a force-sensing operation by

automatically moving the door open and close. The garage door opener will sound an audible and

visual alert before automatically opening and closing the door. The garage door opener will beep

three times, conrming that the Automatic Force Setup completed successfully. Adjustment is

complete.

If you hear one long beep after the door attempts to move, then the Automatic Force Set Up has

not completed successfully. Please start over at step 1 of Program the Travel..

Adjustment

Automatic Force Set Up

1.5 Once the door is in the desired DOWN

position press and release the Adjustment

Button. The garage door opener lights will

ash twice. Program the Travel is now

complete. If the garage door opener lights

ash 5 times, then programming has timed

out and the Travel Limits have not been

set. Please restart the Program the Travel

process.

1.6 Add the Step

Saver sticker under

the yellow program

button.

Produktspecifikationer

Varumärke:	Liftmaster
Kategori:	Inte kategoriserad
Modell:	050ACTBLKMC
Färg på produkten:	Zwart
Energieffektivitetsklass (gammal):	A
Justerbar i höjdled:	130 mm
Skärm diagonal:	27 "
Upplösning:	2560 x 1440 Pixels
Pekskärm:	Nee
Original bildförhållande:	16:9
Typ av anslutningskontakt:	3,5 mm
Betraktningsvinkel, horisontell:	178 °
Betraktningsvinkel, vertikal:	178 °
Medföljande kablar:	AC
Skärmform:	Flat
Typiskt kontrastförhållande:	1000:1
Ursprungsland:	China
Antal HDMI-portar:	2
DVI-port:	Nee
Monteringsalternativ för kabellås:	Nee
Inbyggda högtalare:	Ja
Genomsnittlig effekt:	6 W
Strömförbrukning (i standby):	- W
Antal högtalare:	2
Hörlursutgångar:	1
Certifiering:	WEEE, ICE, ISO 9241-3x Class 1, CE, FCC
Display, antal färger:	1.073 biljoen kleuren
HD typ:	Quad HD
Displayteknik:	LED
Respons tid:	5 ms
Pixelpitch:	0.2331 x 0.2331 mm
Grafikupplösningar som stöds:	2560 x 1440
VESA montering:	Ja
Panelmonteringsgränssnitt:	100 x 100 mm
Hållbarhetscertifikat:	RoHS, ENERGY STAR
Ljusstyrka (typiskt):	300 cd/m²
Integrerad TV-tuner:	Nee
Inbyggd kamera:	Nee
Djup (utan bas):	44.3 mm
Höjd (utan bas):	362.2 mm
Bredd (utan bas):	630 mm
Vikt (utan bas):	4500 g
Antal DisplayPorts:	1
Enhetsbredd (med stativ):	630 mm
Djupenhet (med stativ):	244.5 mm
Enhetshöjd (med stativ):	547.2 mm
Vikt (med stativ):	6900 g
Typ av panel:	ADS
Roterbar:	Ja
Horisontellt vridbar:	0 - 160 °
Hörlurarna avstängda:	Ja
Bildområde:	Mat
Inbyggd USB-hubb:	Nee
Bildstorlek (horisontell):	596.7 mm
Bildstorlek (vertikal):	335.7 mm
Stativ ingår:	Ja
Gångjärn:	Ja
Pivothörn:	0 - 90 °
AC-ingångsspänning:	100 - 240 V
Strömförbrukning (typiskt):	50 W
Tiltvinkelområde:	-3 - 18 °
lutningsjusteringar:	Ja