Lorex E581CB-E Bruksanvisning

Lorex övervakningskamera E581CB-E

Läs nedan 📖 manual på svenska för Lorex E581CB-E (2 sidor) i kategorin övervakningskamera. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
5MP HD Bullet IP Camera
E581CB_QSG_EN_R2
Quick Start Guide
English Version 2.0
Copyright © 2019 Lorex Corporation
As our products are subject to continuous improvement, Lorex reserves the right
to modify product design, specifications and prices, without notice and without
incurring any obligation. E&OE. All rights reserved.
• For a full list of compatible recorders, visit lorex.com/compatibility.
• Not intended for submersion in water. Installation in a sheltered
location recommended.
• This camera includes an Auto Mechanical IR Cut Filter. When the
camera changes between Day/Night viewing modes, an audible clicking
noise may be heard from the camera. This clicking is normal, and
indicates that the camera filter is working.
Disclaimers
Dimensions
6.3” / 160mm2.5” / 62mm
E581CB SERIES
• 5MP HD Bullet IP Camera
• Mounting Kit*
• Ethernet Extension Cable with Pre-attached RJ45
Cable Gland*
* Per camera in multi-camera packs.
Package Contents
ATTENTION:
It is recommended to connect the camera to the NVR or an external PoE
switch. If using a DC power adapter (not included) with the camera, a
REGULATED power supply is REQUIRED for use with this camera. Use of
a non-regulated, non-conforming power supply can damage this product
and voids the warranty.
• Use the camera only with compatible Lorex NVRs.
• Read this guide carefully and keep it for future reference.
• Follow all instructions for safe use of the product and handle with care.
• Use the camera within given temperature, humidity and voltage levels
noted in the camera’s specifications.
• Do not disassemble the camera.
• Do not point the camera directly towards the sun or a source of
intense light.
• Use only a regulated power supply with the product (optional). Use of a
non-regulated, non-conforming power supply can damage the product
and void the warranty.
• Periodic cleaning may be required. Use a damp cloth only. Do not use
any harsh, chemical-based cleaners.
• The supplied cable is rated for surface mounting only. Cables for in-wall
and floor-to-floor installations are sold separately (CMR type). These
and other cables are available at lorex.com.
Safety Precautions
• Point the camera where there is the least amount of obstructions
(i.e., tree branches).
• Install the camera where vandals cannot easily reach.
• Secure cabling so that it is not exposed or easily cut.
• This camera is rated for outdoor use. Installation in a sheltered
location is recommended.
Installation Tips
www.lorex.com
Need Help?
Visit us online for up-to-date software
and complete instruction manuals
Click on the Downloads tab
4
Visit lorex.com
Search for the model
number of your product
Click on your product
in the search results
3
2
1
Resources
The pre-attached RJ45 cable gland covers the camera’s Ethernet
connector and the RJ45 plug to provide weather-resistance and
protection from dust, dirt and other environmental contaminants.
To use the RJ45 cable gland:
RJ45 Cable
Gland Barrel
Camera Ethernet
Connector
NOTE: The RJ45 cable gland is weather-resistant. Seal the cap with
silicone and/or electrical tape for additional sealing if it will be exposed
to precipitation regularly.
Twist the RJ45 cable gland
barrel securely onto the
camera Ethernet connector.
Using the RJ45 Cable Gland (Optional)
Setup Diagram
CameraNVR
Scenario 1: Connect Cameras to NVR
Scenario 2: Connect Cameras to Local Area Network (LAN)
Router
Camera
NVR
Router
PoE Switch
ATTENTION:
• This camera is only compatible with select NVRs. For a list of
compatible recorders, visit lorex.com/compatibility.
• You must connect the camera to a supporting H.265 NVR to take
advantage of H.265 compression. For instructions on enabling
H.265 compression, visit lorex.com, and search for “How do I
enable H.265 compression?”.
E581CB_QSG_EN_R2
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your NVR.
Before Installing the Camera
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the on cable notch
the base. This will keep the camera
base flush to the surface when mounted. Cable Notch
To install your camera:
Adjustment Screw
A. Rotate the camera base 360°
B. Twist the camera around the stand 360°
C. Tilt the camera on the stand up to 90°
• You can use a RJ45 coupler or switch (not included) to connect male
ends of Ethernet cable together.
• To extend the cable run beyond 300ft (91m), a switch will be required
(sold separately).
Extend the Ethernet cable run for your camera up to 300ft (91m).
See table below. It is recommended to use UL CMR approved cables
available at lorex.com.
Cable Extension Options
Cable Type Max Cable Run
Distance
Max # of
Extensions
CAT5e (or higher) Ethernet cable 300ft (91m) 3
Problem Solution
No picture /
signal
• Ensure the camera is connected to a compatible NVR.
For full camera compatibility, visit
lorex.com/compatibility.
• The camera may take up to 1 minute to power up after
being connected to the NVR. Wait two minutes before
following the steps below.
• Ensure the camera is connected to your NVR or to your
local network.
• If you are not using PoE, you must connect the camera
to a 12V DC power adapter (not included).
• If the camera is connected to the LAN, you must search
your network for cameras using the NVR. See the NVR’s
instruction manual.
• Ensure your NVR is properly connected to a TV/monitor.
• There may be an issue with your extension cable run.
Connect the camera to the NVR using a different
Ethernet cable.
Picture is too
bright
• Ensure your camera isn’t pointed directly at a source of
light (e.g., sun or spot light).
• Slide the sunshade forward to block excess light.
• Move your camera to a different location.
• Check the brightness and contrast settings on the NVR.
Picture is too
dark
• If using during the day, the camera may not be getting
enough light. Slide the sunshade backwards to let in
more light.
• Check the brightness and contrast settings on the NVR.
Night vision is
not working
• The night vision activates when light levels drop. The
area may have too much light.
Picture is not
clear
• Check the camera lens for dirt, dust, spiderwebs. Clean
the lens with a soft, clean cloth.
• Make sure that the cable run is within the limitations
specified in the section ‘Cable Extension Options’.
• Remove the vinyl film from the camera lens when your
installation is complete.
Bright spot
in video when
viewing camera
at night
• Night vision reflects when pointing a camera through a
window. Move the camera to a different location.
Picture is in
color in dark
conditions
• This camera comes with an image sensor that is extra
sensitive to light, meaning that the camera stays in
color mode at low-light conditions. For instructions on
how to make your camera switch to night mode, visit
lorex.com, and search for “How do I make my camera
switch to night mode?”.
Troubleshooting
Connect the Ethernet cable to
the camera.
Connect the other end of the
Ethernet cable to the NVR’s PoE
ports. The camera may take a
minute to power up after
being connected.
Connecting the Camera
Connect the other end of the
Ethernet cable to a router or
switch on your network. See
your NVR manual for details on
connecting the camera to your
NVR using a switch or router.
Camera NVR
OR
(Optional)
12V DC Power
Ethernet Cable
NOTE: A 12V DC power adapter
(model#: ACCPWR12V1, not
included) is only required if
connecting the camera’s Ethernet
cable to a router or switch that
does not support PoE.
Installing the Camera
4. Use a Philips head
screwdriver (not
included) to loosen
the adjustment
screw.
5. Adjust the camera position as needed:
6. Tighten the adjustment screw to secure the position.
7. Remove the vinyl film from the camera lens when your
installation is complete.
1. Use the included mounting template to mark holes for the
screws. Drill holes for the mounting screws.
NOTE: Insert the included drywall anchors if you are
installing the camera in drywall.
2. Connect cables as shown in the section “Connecting the
Camera”.
3. Feed the cable through the mounting surface or cable
notch and mount the camera stand to the surface using
the provided screws.
AB
C

Produktspecifikationer

Varumärke: Lorex
Kategori: övervakningskamera
Modell: E581CB-E

Behöver du hjälp?

Om du behöver hjälp med Lorex E581CB-E ställ en fråga nedan och andra användare kommer att svara dig


övervakningskamera Lorex Manualer

Lorex

Lorex E891AB Bruksanvisning

7 Oktober 2024
Lorex

Lorex DP181-42NAE Bruksanvisning

29 September 2024
Lorex

Lorex E842CA Bruksanvisning

24 September 2024
Lorex

Lorex E842CAWP Bruksanvisning

24 September 2024
Lorex

Lorex E842CAB Bruksanvisning

24 September 2024
Lorex

Lorex LNE45DDW Bruksanvisning

23 September 2024
Lorex

Lorex LNB45ABB Bruksanvisning

23 September 2024
Lorex

Lorex W261AQ Bruksanvisning

23 September 2024
Lorex

Lorex LNE45DDB Bruksanvisning

23 September 2024
Lorex

Lorex LNB45ABW Bruksanvisning

23 September 2024

övervakningskamera Manualer

Nyaste övervakningskamera Manualer

Speco Technologies

Speco Technologies WDRB11H Bruksanvisning

27 Oktober 2024
Vivotek

Vivotek AI-108 Bruksanvisning

27 Oktober 2024
Acti

Acti E88 Bruksanvisning

27 Oktober 2024
Yale

Yale WIPC-303W Bruksanvisning

27 Oktober 2024
Grandstream

Grandstream GXV3611IR_HD Bruksanvisning

27 Oktober 2024
Airlive

Airlive DM-720 Bruksanvisning

27 Oktober 2024
Speco Technologies

Speco Technologies O8B7M Bruksanvisning

27 Oktober 2024
Grandstream

Grandstream GXV3615W Bruksanvisning

27 Oktober 2024
Vivotek

Vivotek IP8133 Bruksanvisning

27 Oktober 2024
Olympia

Olympia OC 1280P Bruksanvisning

27 Oktober 2024