Lorus Z015 Bruksanvisning

Lorus Titta Z015

Läs nedan 📖 manual på svenska för Lorus Z015 (2 sidor) i kategorin Titta. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
C H A R A C T E R I S T I C S
1. Time mode
Display of hour, minute, second, month, date and
Day of the week. Choice between 12-hour format
and 24-hour format. Dual time display function.
Hourly chime signal.
2. Heart rate measurement mode (HRM mode)
Heart rate measurement wit h finger sensor.
The watch can measure your heart rate and
percentage of maximum heart rate (MHR.)
Heart Rate Training Zone Alert
If the tested heart rate exceeds the limit settings,
the watch will beep and display will flash to give
you audio and visual alert. It will remind you to
adjust exercise intensity to stay in target heart
rate zone.
3. Stopwatch mode
Measurement of up to 23 hours 59 minutes and
59 seconds in 1/100-second increments. Lap time
measurement is possible.
4. Recall mode
A maximum of 16 exercise data can be recorded,
ind l ucding exe rcise t ime , he arrt rat e and
percentage of maximum heart rate (MHR.)
5. Calorie mode
Display of calories consumed, fat burnt and BMI
(Body Mass Index) based on pre-filled personal
data
6. Alarm mode
4-channe l alarm including ONCE (single-
time alarm)Monday to Friday,Monday to
Saturday and ALL (daily alarm)
7. Timer mode
Measurement of up to 23 hours 59 minutes and
59 seconds
8. Illuminating Light
If you pre ss But t on D, t he built -in e lect ro -
luminescent (EL) light illuminates the display for
easy viewing in darkness.
T I M E M O D E
1 In the Time mode, keep pressing down Button
D for 2 seconds to enter the time setting mode.
(The second digits start flashing.)
2 <Second setting>
Press Button A or B in accordance with a
time signal. The second digits are reset
to 00 and start counting immediately.
When the second digits are greater than
“29,one minute is added and the second
digits are reset to 00.
3 Press Button C to confirm the second setting
and move on to the next item.
Selection of the item to be adjusted (flashing)
is made in the following order when Button C
is pressed.
NREZ015 8-2011
CAL. Z015 (R23 SERIES)
How to s et t h e ti me/ ca len dar
1. Wear the watch on your wrist.
2. Lay your fingers down flat, firmly on the two
sensor areas as shown in the pictures below.
Tips for accurate heart rate reading
1. Press your fingers with equal strength and
stay motionless.
2. If your fingers are extremely dry, moisten
your fingers.
3. If the temperature is low, rub your hands
to warm them up.
S T O P WAT C H M O D E
1. Pre ss Butt on C unt il the wat ch ent ers t he
Stopwatch mode.
2. Press Button A to start or stop the stopwatch.
3. Press Button B to record lap times.
Up to 16 lap time records can be saved.
• Todeleteanexerciserecord,whichincludes
lap time, heart rate, calorie consumed and
fat burnt, keep pressing down Button B for 2
seconds.
• Ifyouchangethemodetoadifferentmode
while the stopwatch is running, the stopwatch
keeps running with the “STP indicator flashing
on the display.
How to s et t h e ti me i n t he second t ime z on e
3. When your heart rate is displayed, press Button
B to save it.
R E C A L L M O D E
1. Press Button C until the watch enters the Recall
mode.
2. Press Button A to display the recorded data one
by one.
3. To delete all the records including lap time,
heart rate, calorie consumed and fat burnt, keep
pressing down Button B for 2 seconds.
If the stopwatch is running, skip the Recall mode
when you press Button C to switch modes.
P E R S O N A L I N F O R M AT I O N S E T T I N G
1. In the Calorie mode, keep pressing Button D for
2 seconds, to enter the personal data setting
mode.
2. Press Button C to switch the item to be adjusted.
Selection of the item to be adjusted (flashing)
is made in the following order when Button C is
pressed.
Set up your personal data before you measure your
heart rate or do exercise. Based on your personal
data, the watch calculates calorie consumed and
fat burned while you excercising.
How to i np u t yo u r per son al in f o r ma t io n
F/M HI AGE KG HG EM ⇒ ⇒ TG LO
4 To set the digits for each item, press Button A to
increase the digits or press Button B to decrease
the digits. Keep pressing down each button to
fast-forward or fast-backward.
5 After all the adjustments are completed, press
Button D to return to the Time mode.
* If you choose 12-hour format, the PM icon
appears on the display after 11:49 a.m.
How to s et t h e ho ur l y ch im e
Press Button B to turn the hourly chime ON or OFF.
When the hourly time is turned on, the chime
icon appears on the display.
C A L O R I E M O D E
1. Press Button C until the watch enters the Calorie
mode.
2. Pre ss But to n A t o swit ch b et wee n cal o rie
consumption display (kcal) and fat burnt display
(kg and lbs.)
3. Keep pressing down Button B to display BMI.
• CalculationsintheCaloriemodeisbasedonthe
data obtained by the stopwatch and heart rate
measurement.
• Foraccuratecalculationofcalorieconsumption
and fat burnt, start the stopwatch first and keep
measuring your heart rate.
B U T T O N S A N D D I S P L AY S
AL
TMR
STP
LAP
KCAL
PM
A
B
C
D
Start/Stop
Lap/Reset
Mode
Set/EL Light
To change the display mode, press Button C. The
display mode changes in the following order.
HRM
Stopwatch
Recall
Calorie
Alarm
Countdown timer
Time
C
C
C
C
C
C
C
Du al T ime D ispla y f un ct ion
The watch can display the time in two time zones:
local time zone and second time zone. To switch
between the time zones, press Button A.
1. In the Time mode, press ButtonA to display
the second time zone.
2. Keep pressing down Button D for 2 seconds
to enter the time setting mode.
3. Press Button C to switch the items to be
adjusted.
4. To set the digits for each item, press Button
A to increase the digits or press Button B to
decrease the digits. Keep pressing down each
button to fast-forward or fast-backward.
During the minute setting, the minute digits
increase or decrease by 30 at a time.
5. After all the adjustments are completed, press
Button D to exit the time setting mode.
H E A R T R AT E M E A S U R E M E N T M O D E
Press Button C until the watch enters the Heart rate
measurement (HRM) mode.
Af t e r t h e wat c h e nt e rs t he HR M m o de , t h e
measurement circuit is automatically activated. If
no heart rate signal is detected, or the heart rate
signal is inconsistent, the heart rate measurement
function will be automatically inactivated to save
power. If this happens, press Button A to reactivate
the heart rate measurement function.
How to m ea su re y ou r h ea r t r a t e
local time zone second time zone
Exerc ise Mode
Please input your personal information before doing
exercise and measuring heart rate. When you start
exercising, turn the stopwatch ON, and then enter
the HRM mode. The result of heart rate measurement
will be used to calculate calorie consumption and
fat burnt. After your heart rate reading is obtained,
press Button B to save the current lap record and
heart rate reading. The watch can record 15 groups
of data at the most. The calculation of calorie
consumption and fat burnt wont be influenced
even if you don’t save the data. Stop the stopwatch
if you don’t want to get your heart rate measured.
NREZ015.indd 1 11/07/05 10:11
Press Button C until the watch enters the Countdown
timer mode.
Ho w to s e t t he c ou nt dow n pe r iod
1. Keep pressing down Button D for 2 seconds
to enter the timer setting mode.
2. Press Button C to switch the items to be
adjusted.
3. To set the digits for each item, press Button
A to increase the digits or press Button B to
decrease the digits. Keep pressing down each
button to fast-forward or fast-backward. To set
the gender, press either Button A or Button B to
switch between F (female) and M (male.)
4. Press Button D to exit the personal data setting
mode.
When setting weight, the unit of weight is the same
as that of fat burnt. If the unit for fat burnt is KG,
then the unit for weight is also KG. If the unit for
fat burnt is LBS, then the unit for weight is also LBS.
Default unit is KG.
If the tested heart rate exceeds the limit settings,
the watch will beep and display fill flash to give
you audio and visual alert. You can adjust exercise
intensity accordingly to optimize the workout effect.
When the stopwatch is running, you cannot set
the personal information.
Ho w to u se th e co un t d ow n ti mer
The miniature battery CR2032 which powers your
watch should last approximately 2 years. However,
because it is inserted at the factory, the actual
life of the battery once in your possession may
be less than 2 years.
Be sure to replace the battery to prevent any
possible malfunction as soon as it runs down. To
replace the battery we recommend taking the
watch to a local watch repair shop.
Note: If the alarm and timer are used for more
than 20 seconds a day, the illuminating
light for more than 3 seconds a day, and
the heart rate is tested 15 times a day for 30
seconds, the battery life may be less than
the specified period.
B AT T E R Y C H A N G E
I L L U M I N AT I N G L I G H T
In any mode press Button D to illuminate the
display for about 4 seconds.
Note:
1. The backlight of the watch employs an electro-
luminescent (EL) light, which tends to lose
illuminating power after very long use.
2. The illumination provided by backlight may be
hard to see when viewed under direct sunlight.
C A R E O F Y O U R L O R U S WAT C H
This watch contains precise electronic components.
Never attempt to open the case or remove the
back cover.
• BATTERY
CAUTION
Do not expose the old battery to re or
recharge it. Keep it at a place beyond
the reach of chil dren. If a child swallows
it, consult a doctor immediately.
• WATERRESISTANT
Con d i t i on
of u s e Ac c i d e n t a l
con t a c t
wi th w a t e r,
s u ch a s
s p l a s h e s
a n d r a i n
Sw i m m i n g
a n d t a ki n g
a s h o wer
Sk i n
d i v i n g
Sc u b a
d i v i n g
Indication
on the dial/
case back
No
I nd ic a t i on
* If your watch is 200 M/20 BAR, 100 M/10 BAR or
50 M/5 BAR water resistant, it is so indicated on
the dial/case back.
• Donotoperatethebuttonswhenthewatchis
wet.
• Ifthewatchisexposedtosaltwater,rinseitin
fresh water and then wipe it thoroughly dry.
 Shouldyoufindanywaterorcondensation
inside the watch, immediately have it checked.
Water can corrode electric parts inside the
case.
NO NO NO
YE S YE S NO NO
YE S YE S N O
NO NO NO
YE S
WATER
RESI S T A NT
WATER
RESI S T A NT
( 5 0M / 5  BA R
)
WATER
RESI S T A NT
1 00 M /1 0  BA R 
or a bo ve
(
NO
(
Caution:
Leather straps are not water resistant except
so indicated, even if the watch head is water
resistant.
• ALLERGICREACTION
Because the case and band touch the skin directly,
it is important to clean them regularly. If not, shirt
sleeves may be stained and those with delicate
skin may develop a rash. Please wear the watch
with some play to avoid any possible allergic
reaction. If you develop a rash on your wrist, stop
wearing and consult a physician.
• MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away from close contact with
magnetic objects.
• SHOCKSANDVIBRATIONS
Your wat ch m a y be worn for normal spo rts
activities, but be careful not to drop it or hit it on
hard surfaces.
• TEMPERATURE
Your watch is preadjuste d so that const ant
accuracy may be insured at normal tem pera ture.
• CLEANING
Use o nly a so ft cl ot h a nd cl e an wat e r fo r
cleaning your watch. Never use chemicals, as
the waterproof gasket will corrode.
S E R V I C E
When yo ur LORU S wa t ch re quires re pair or
servicing, please see the enclosed WARRANTY/
GUARANTEE.
P r i n t e d i n C h i n a
YE S
A L A R M M O D E
1. Press Button C until the watch enters the Alarm
mode.
2. Press Button A to select the alarm channel.
Ho w to s e t t he al ar m
1. In the selected alarm channel, keep holding
down Button D for 2 seconds to enter the
alarm setting mode.
2. Press Button C to switch the items to be
adjusted.
C
HourMinute
* The alarm sounds at the designated time for
20 seconds.
* To stop the alarm, press any button.
C O U N T D O W N T I M E R M O D E
3. To set the digits for each item, press Button
A to increase the digits or press Button B to
decrease the digits. Keep pressing down each
button to fast-forward or fast-backward.
4. Press Button D to confirm the timer setting and
exit the timer setting mode.
• Ifyouchangethemodetoadifferentmode
while the countdown timer is running, the
timer keeps running with the “TMR indicator
flashing on the display.
Percentage
of MHR
Exercise
intensity Exercise effect Fat and sugar
burnt
<50%
Rest or
moderate
exercise (e.g.
walking )
Low calorie
expenditure
and mainly
sugar burnt
50% - 60%
Jogging.
Breathing is
regular.
War m- up
aerobic
exercise;
stress relief
Fat burnt
increases and
less sugar
burnt
60% - 70%
Running at a
comfortable
speed.
Breathing
becomes
deeper.
You can
carry on a
conversation.
Cardiovascular
exercise; the
speed you drop
back to after
running at a
fast speed;
weight loss
Maximum fat
burnt and less
sugar burnt
70% - 80%
Running at
a moderate
speed.
You can only
talk in short
phrases.
Improve
aerobic
capacity. The
best zone for
improving
cardiovascular
and respiratory
systems.
Less fat but
more sugar
burnt
80% -90%
Running at a
fast speed.
Breathing is
heavy.
Improve
anaerobic
capacity;
develop speed.
Seldom fat
but maximum
sugar burnt
90% -100%
Sprinting.
Breathing is
labored.
Most people
can only stay
in this zone for
short periods.
Improve
anaerobic
exercise
performance
and your
tolerance;
develop
muscles.
Maximum
sugar burnt and
almost no fat
burnt
A P P E N D I X
Relationship between percentage of MHR and Fat
Burnt
Generally, individual heart rate varies person to
person. The minimal heart rate for a normal person
is resting heart rate. (RHR), which is about a person’s
heart rate in the morning: awake but still lying down
with no physical exertion. The maximal safe heart
rate for an individual is maximum heart rate (MHR),
which is based on one’s age. Percentage of MHR
relates to one’s MHR.
The higher the percentage of MHR, the more calories
consumed. Those calories are from sugar and fat.
The relationship between percentage of MHR and
calorie consumption is shown in below form.
BMI
The body mass index (BMI) is a statistical measure of
body weight based on a person’s weight and height.
BMI provides a reliable indicator of body fatness for
most people, which allows for the comparison of
individuals of different heights in terms of their weight.
BMI is widely used to identify weight problems within
a population, usually whether individuals are normal,
overweight or obese.
However, please remember that BMI is only a guide
and other issues such as body type and shape have
a bearing as well. Therefore, it does not accurately
apply to juveniles, athletes, elderly populations,
pregnant women or those who are doing weight
training. If you think your BMI is incorrect, please
consult your doctor and do body fat test.
BMIforadults(justaguide)
BMI range kg /m2 Category
Less than 18 Underweight
18.5 - 24.9 Normal
22 - 24 Fitness
Over 25 Overweight
Press Button A to start or stop the countdown
timer.
When the countdown is stopped, press Button
B and the countdown time will automatically
restore to the last setting. To stop the alarm,
press any button.
C C
Second Minute Hour
3. To set the digits for each item, press Button
A to increase the digits or press Button B to
decrease the digits. Keep pressing down
each button to fast-forward or fast-backward.
4. After all the alarm settings are completed,
press Button D to exit the alarm setting mode.
NREZ015.indd 2 11/07/05 10:11

Produktspecifikationer

Varumärke: Lorus
Kategori: Titta
Modell: Z015

Behöver du hjälp?

Om du behöver hjälp med Lorus Z015 ställ en fråga nedan och andra användare kommer att svara dig




Titta Lorus Manualer

Titta Manualer

Nyaste Titta Manualer