Lowrance LDT3200 Bruksanvisning
Läs nedan 📖 manual på svenska för Lowrance LDT3200 (12 sidor) i kategorin Navigator. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/12
1
Pub. 988-0099-071
LDT-3200
Digital Temperature Gauge
Installation & Operation Instructions
The LDT-3200 combines a temperature gauge, voltmeter and clock in one
housing. It displays the temperature in either Fahrenheit °F or Celsius
°C and may be set to rotate between four gauge displays or "pages." The
unit fits in a standard 2-1/8" (54 mm) hole used by most marine equip-
ment manufacturers.
The gauge and its temperature sensor are designed to show surface water
temperature in a transom installation, but the sensor can be installed to
monitor the temperature elsewhere, such as in a live well.
LDT-3200 temperature gauge.
Mounting Preparations
When installed, the gauge will cover an area on the dash 2-3/8" (60.3 mm)
in diameter. To mount the unit, first make sure there is at least 2-3/4"
(70 mm) from the front of the dash to any obstruction behind the dash.
The maximum usable dash thickness is 1-1/8" (28.5 mm). Also, be sure
there is room to route the power and sensor cables. The following figure
shows gauge dimensions.
2
Dash installation, cross-section view.
Caution:
You should read over the entire installation section before drilling
any holes in your vessel!
You can install this gauge in some other order if you prefer, but we rec-
ommend this installation sequence, which is summarized below:
1. Determine the location for the gauge so you can plan how and where to
route the cables. This will help you make sure you have enough cable
length for the desired configuration.
2. Determine the location of your battery or other power connections,
along with the power cable route.
3. Determine the location for the temperature sensor and its cable route.
4. Determine the location for the alarm buzzer and its wire route.
5. If you want to turn on the gauge backlights whenever you turn on your
dashboard lights, locate your boat's dash light switch and determine how
to route the dash light wires to it.
6. Install the temp sensor, connect power wires to the battery and route
the power/sensor cable to the gauge location.
7. Install the gauge, and connect the power/sensor cable.
8. Connect the buzzer wires and install the buzzer. If desired, connect the
dash light wires to the boat's dash light switch.
2-3/4"
(70 mm)
2-3/8"
(60.3 mm)
Gasket
Threaded mounting collar
Dash
Cables
3
Recommended Tools and Supplies
Supplies are not included, unless otherwise indicated. A transom mount
requires one #8 stainless steel screw (3/4" long) and a high quality, ma-
rine-grade above- or below-waterline sealant/adhesive compound. If you
want to make a pilot hole for the screw, use a drill and a 1/8" drill bit. If
you prefer the option of routing the temp sensor cable through the tran-
som (instead of over it), you will also need a 1/2" drill bit.
If the dash does not have a standard 2-1/8" (54 mm) hole, you will need a
drill or saw to make the hole. Carefully measure the dash thickness and
the hole area before cutting or drilling.
A screwdriver is needed for mounting the temp sensor. The buzzer in-
stallation requires two cable ties.
If you need to extend any of the wires, use a minimum of 24 gauge wire
and wire connectors of your choice. Wire nuts or electrical tape are re-
quired to cap any unused bare wires.
Mounting
The temperature sensor can be mounted in any convenient location.
However, make sure it is placed on the transom where it will be in con-
tact with the water at all times. Make sure the location does not interfere
with the boat's trailer.
Temp sensor on transom, with cable routed through the transom.
After determining the location, use the sensor as a template and mark
the hull for the screw's pilot hole, if desired. Route the sensor and cable
over or through the transom to the mounting location. If routing through
the transom, drill a 1/2" hole to accommodate the sensor. Attach the sen-
sor to the hull with one #8 stainless steel screw, then seal the screw with
the below-waterline sealant compound.
Caution:
If you drill a hole in the transom for the cable, make sure it is lo-
cated above the waterline. After installation, be sure to seal the ca-
ble hole with the same marine grade above-or below-waterline
sealant used for the screw.
Produktspecifikationer
| Varumärke: | Lowrance |
| Kategori: | Navigator |
| Modell: | LDT3200 |
Behöver du hjälp?
Om du behöver hjälp med Lowrance LDT3200 ställ en fråga nedan och andra användare kommer att svara dig
Navigator Lowrance Manualer
25 September 2024
25 September 2024
2 September 2024
21 Augusti 2024
18 Augusti 2024
17 Augusti 2024
13 Augusti 2024
12 Augusti 2024
7 Augusti 2024
26 Juli 2024
Navigator Manualer
- Navigator Philips
- Navigator Garmin
- Navigator Kenwood
- Navigator Medion
- Navigator Nokia
- Navigator Pioneer
- Navigator Acer
- Navigator Alpine
- Navigator Airis
- Navigator Bushnell
- Navigator Blaupunkt
- Navigator Harman Kardon
- Navigator Humminbird
- Navigator Skoda
- Navigator Sanyo
- Navigator Sylvania
- Navigator Celestron
- Navigator Binatone
- Navigator Magellan
- Navigator Clarion
- Navigator Mio
- Navigator Uniden
- Navigator Audiovox
- Navigator Insignia
- Navigator Goclever
- Navigator Dual
- Navigator Navigon
- Navigator Boss
- Navigator Cobra
- Navigator TomTom
- Navigator Navitel
- Navigator Navman
- Navigator Wahoo Fitness
- Navigator Lanzar
- Navigator Jensen
- Navigator Zenec
- Navigator Danew
- Navigator Rand McNally
- Navigator VDO
- Navigator Soundstream
- Navigator VDO Dayton
- Navigator Igo
- Navigator Route 66
- Navigator Falk
- Navigator ModeCom
- Navigator Sygic
- Navigator Raymarine
- Navigator Pharos
- Navigator Viamichelin
- Navigator Xzent
- Navigator V7
- Navigator ESX
- Navigator LXNAV
- Navigator Planet Audio
- Navigator Eclipse
- Navigator TELE System
- Navigator IZZO Golf
- Navigator Zoleo
- Navigator Dashmate
- Navigator GlobalSat
Nyaste Navigator Manualer
19 Oktober 2024
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
12 Oktober 2024
12 Oktober 2024
12 Oktober 2024
10 Oktober 2024
9 Oktober 2024
9 Oktober 2024