Magnavox MM438 Bruksanvisning

Magnavox högtalare MM438

Läs nedan 📖 manual på svenska för Magnavox MM438 (1 sidor) i kategorin högtalare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/1
IMPORTANT SAFETY INSTRUCTIONS
78
CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT
REMOVE THE COVER (OR BACK). NO USER
SERVICEABLE PART INSIDE, REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DANGEROUS VOLTAGE: The lighting flash with arrowhead
symbol ,within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’
enclosure, that maybe of sufficient magnitude to constitute
ATTENTION: The exclamation point within an equilateral
triangle is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
1 Read these instructions .
All the safety and operating instructions should be read
before the appliance is operated.
2 Keep these instructions .
The safety and operating instructions should be kept for
future reference.
3 Heed all warnings.
All warnings on the appliance and in the operating
instructions should be adhered to.
4. Follow all instructions
All operation and use instructions should be followed.
5. Do not use this apparatus near water
The appliance should not be used near water; for example,
near a bath tub, washbowl, kitchen sink, laundry tub, in
awet basement, or near a swimming pool.
6. Clean only with dry cloth
The appliance should be cleaned only as recommended by
the manufacturer.
7 Do not block any ventilation openings. Install in .
accordance with the manufacturer’ instructions.
Slots and openings in the cabinet and in the back or bottom
are provided for ventilation, to ensure reliable operation of
the product and to protect it from overheating. These
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or similar surface. This product should never be
placed near or over a radiator or heat source. This product
should not be placed in a built-in installation, such as a
bookcase or rack unless proper ventilation is provided or
the manufacturer’ instructions have been adhered to.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Product the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. Only use attachments / accessories specified by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket,
or table specified by the manufacturer,
or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
An appliance and cart combination should be moved
with care. Quick stop, excessive force and uneven
surfaces may cause the appliance and cart
combination to overturn.
13. Unplug this apparatus during lightning
storms or when unused for long periods of time.
To protect your product from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the product due to lightning and power-line surges.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. Power source
This product should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of power supply to your
home, consult your appliance dealer or local power
company. For products intended to operate from
battery power, or other source, refer to the operation
instructions.
16. Power lines
An outside antenna system should not be located in
the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as
this can result in a risk of fire or electric shock.
18. Object and liquid entry
Never push objects of any kind into the product
through openings as they may touch dangerous
voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type of
liquid on the product.
19. Outdoor antenna grounding
If an outside antenna is connected
to the product, be sure the antenna
system is grounded so as to provide
some protection against voltage surges
and built up static charges. Section 810
of the National Electric Code ANSI/ NFPA 70 provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-
in wire to an antenna discharge product, size of
grounding conductors, location of antenna-
discharge product, connection to grounding
electrodes and requirements for the grounding
electrodes.
20. Service
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
21. Replacement parts
When replacement parts are required, be sure the
service technician uses replacement parts specified
by the manufacturer or those that have the same
characteristics as the original parts. Unauthorized
substitutions may result in fire or electric shock or
other hazards.
22. Safety check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
23 Wall or ceiling mounting.
The product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
24. Damage requiring service
A. Unplug this product from the wall outlet and refer
service to qualified service personnel under the
following conditions.
B. When the power- supply cord or plug is damaged.
C. If liquid has been spilled or objects have fallen into
the product.
D. If the product has been exposed to rain or water.
E. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an adjustment of other controls
may result in damage and will require extensive
work by a qualified technician to restore the
product to its normal operation.
If the product has been dropped or the cabinet has F.
been damaged.
G. When the product exhibits a distinct change in
performance- this indicates a need for service.
25. Note to CATV system installer
This reminder is provided to call the CATV system
installer' attention to Article 820- 40 of the NEC
that provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
FCC NOTICE:
or relocate the receiving antenna. Reorient
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV
technician for help.
FCC STATEMENT:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation. The antenna(s) used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from all
persons and must not be co-located or operating
in conjunction with any other antenna or
transmitter.
FCC WARNING:
To assure continued operation, follow the attached
installation instructions and use only shield cables
when connecting to other devices. Changes or
modifications not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
NOTE: Refer all servicing to qualified service personnel.
Servicing is required when the unit has been damaged
in any way such as the following: the power-supply
cord or plug has been damaged, liquid has been spilled
into unit, the unit has been exposed to rain or
moisture, the unit has been dropped or the unit does
not operate normally.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
Before using the unit, be sure to read all operating
instruction carefully, please note that these are general
precautions and may not pertain to your unit. For example,
this unit may not have the capability to be connected to an
outdoor antenna.
POWER SOURCE:
TROUBLESHOOTING GUIDE:
s
s
s
s
To Wall Outlet
The unit has a built in Li-ion rechargeable battery, recharge it before use or when it is drained as follows:
1. Connect the small plug from the supplied AC/DC Adaptor to the DC IN Jack on the rear of unit.
2. Plug the AC/DC Adaptor to the AC wall outlet having AC 100-240V~, 50/60Hz as illustrated below.
3. During charging, the Red Charging Indicator on the rear of unit will illuminate. When finished, it will turn off.
4. During charging, you can also play and listening music at the same time.
Notes:
Your battery will last longer if you're following these simple guidelines for charging and storing.
A. Before first time use, charge it approximately 5 hours until the unit is fully charged.
B. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F).
C. Do not charge longer than 24 hours. Excessive charging or running the unit until battery fully
drains will damage battery. Battery life will be extended if you keep the battery fully charged.
D. Battery life naturally shortens slowly over time.
E. The rechargeable battery incorporated in this product is not user replaceable.
Check the following before requesting service:
SYMPTOM POSSIBLE EC EAUS
Can’ power on Built in battery drained
Volume of the unit was set to
minimum position
No Sound or sound weak
Sound distortion
BT not functioning
POSSIBLE ESOULTION
Volume level of paired/connected
device is in low level
Volume level too high
Volume level of the connected/
paired device too high
The external BT Device had NOT
paired to the unit
The external BT device too far
from the unit
Rise the volume level of the
paired/connected device
Recharge the built-in battery as page 4
Increase the volume level by turning
the MASTER VOL (Volume) Control
Knob clockwise
6
3 4
AUX IN Mode:
To listen to music from an external Audio Player such as a MP3 Player, Discman …etc.
1. Connect one end of the supplied Audio Connection Cable to the AUX
Out/Line Out/Phone Jack on the external Audio Player.
2. Connect the other end of the cable to the AUX IN (Line In) Jack on the rear of unit as the illustrated below:
AUX Out:
To listen music from external Audio Amplifier:
1. Power on the unit and play music in any modes as instructed earlier.
2. Connect one end of the supplied Audio Connection Cable to the AUX/LINE (in) Jack on the external Audio Amplifier.
3. Connect the other end of the cable to the AUX OUT Jack on the rear of unit as the illustrated below:
Microphone:
To sing or play the Electric Guitar with the playing music:
1. Power on the unit and play music in any modes as instructed earlier.
2. Connect the plug from Microphone/Electric Guitar (Not included) to the MIC (Microphone) Jacks on the rear of unit.
3. Turn the MIC VOL (Microphone Volume) Control Knob to adjust the sound level of Microphone/Electric Guitar.
4. Turn the MIC ECHO (Microphone Echo) Control Knob to adjust the echo effect of Microphone/Electric Guitar.
Note: If feedback noise (high audio frequency noise) is sounding from the speakers, turn the MIC VOL
(Microphone Volume) Knob counterclockwise to reduce the microphone volume level or keep the
Microphone away from the speakers.
Note: When the Audio Connection Cable was inserted into the AUX OUT Jack. The sound from speakers will be cut off.
Unplug the cable from the jack after use.
3. Power on the unit and enter to AUX IN (Line In) mode as previously instructed.
Indicator“LinE”will appear on the display.
4. Play the music on the connected Player as usual. (Make sure the volume level of
the connected Audio Player is turned to high level.)
5. During playback,press the >ll Button to mute the sound, press again to turn the sound back.
1 x AC/DC Adapter(Input: AC 100-240 V~, 50/60 Hz, 300mA ; Output: DC 9V, 1300mA， )
SPECIFICATIONS:
PACKAGE INCLUDES:
Power source: Built-in DC 7.4V, 1800 mAh (Total 13.32 WH) rechargeable Li-ion
BT Version: 2.1
BT Operation Distance: ≥32 Feet in open area
1 x User’s Manual
Battery;
Recharge by DC 9 V, 1300mA, through DC IN Jack
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
Radio Frequency: 87.5-108MHz
LOCATION OF CONTROLS:
1. Power ON/OFF Switch
2.LED Display
3.FM Telescope Antenna
4.BASS VOL (Volume) Control Knob
MASTER VOL (Volume) Control Knob
Charging Indicator
DC IN Jack
AUX IN Jack
AUX OUT Jack
USB Port
TF (Micro SD Card) Slot
MIC ECHO (Microphone Echo) Control Knob
MIC VOL (Microphone Volume) Control Knob
23. Speakers with Decorative LED Lights
5.“1” – “6” Buttons (Decorative
LED Lights Blinking Mode Selection/FM
Memory Buttons)
6.
7. l Button
8. Rep (Repeat) Button
9. ll Button
Light (Decorative LED Lights) On/Off Button
l Button10.
11.Mode Button
12.
13.
14.
15.
16.
17.
18.
19.
20.
21. MIC (Microphone) Jacks
22. Five (5) Bands Equalizer
12
USB Device Playback Mode:
To play the music in USB Device:
1. In power off mode, insert the USB Device (Not included) into the USB Port on the rear of unit as the illustrated below:
USB
TF (Micro SD Card) Playback Mode:
Notes:
To play the music in TF (Micro SD Card) :
1. In power off mode, insert the Micro SD Card (Not included) into the TF (Micro SD Card) Slot on
the rear of unit with contact finger face to up as the illustrated below:
2. Power on the unit by press the Power ON/OFF Switch to ON position. The unit will automatically
play the song/music in the TF (Micro SD Card).
3. During playback:
Press the ll Button to mute the sound, press again to turn the sound back.
Press the l or l Button repeatedly to skip tracks.
Press the Rep (Repeat) Button repeatedly to activate and set (or turn off) the repeat playback mode.
Press the Mode Button repeatedly to switch to other playback mode.
Up to 16 GB Micro SD Card the unit supports to play.
Before replacing Micro SD Card, make sure the unit has been powered off.
When inserting the Micro SD Card, make sure the direction you selected is correct. Never insert
violently to avoid damaging the Micro SD Card or the unit.
If it doesn’ work, please check if the direction is correct.
You also need to download the desired music in MP3 format into the Micro SD Card before insert into the unit.
Notes:
FM Radio:
Up to 16 GB USB Device the unit supports to play.
Before replacing USB Device, make sure the unit has been powered off.
When inserting the USB Device, make sure the direction you selected is correct.
Never insert violently to avoid damaging the USB Device or the unit.
You also need to download the desired music in MP3 format into the USB Device before insert into the unit.
1. Power on the unit and enter to Radio mode as previously instructed. Radio frequency will appear on the display.
2. Press the l or l Buttons to automatically search and play the previous/next
available FM station. Repeat the same procedures until the desired FM station was been searched and play.
3. Preset and play:
A. Receiving the desired FM station as previously instructed, press and holding either“1”–“6”Buttons until
“F XX”appear on the display to store the desired FM station into the memory.
B. Repeat the same procedures until all desired FM stations (Maximum 6 stations) were stored into the desired button.
C. Press either“1”–“6”Buttons to play the stored FM station.
Antennas:
The telescope FM antenna is for FM radio reception, which provides adequate reception in most areas.
If reception is weak, extend to its full length or adjust the angle to improve reception.
2. Power on the unit by press the Power ON/OFF Switch to ON position. The unit
will automatically play the song/music in the USB Device.
3. During playback:
Press the ll Button to mute the sound, press again to turn the sound back.
Press the l or l Button repeatedly to skip tracks.
Press the Rep (Repeat) Button repeatedly to activate and set (or turn off) the repeat playback mode.
Press the Mode Button repeatedly to switch to other playback mode.
AUX IN
Audio connection
Cable (included)
Audio connection
Cable (included)
ipad, discman
AUX OUT
OPERATIONS:
General Operation:
1. Recharged the built in Li-ion battery as previously instructed.
2. Press the Power ON/OFF Switch to ON position to power on the unit. The Decorative LED Lights will illuminate.
3. Press the Mode Button repeatedly to switch to desired playback mode. The correspondent indicator will appear
(or illuminate) on the display with your selection (see list below):
Playback Mode: Indicators:
4. During playback,
A. Turn the MASTER VOL (Volume) Control Knob on the top of unit to adjust volume level as desired.
B. Turn the BASS VOL (Volume) Control Knob on the top of unit to adjust the bass level as desired.
C. Slide the control knobs of the Five (5) Band Equalizer up or down to adjust the audio frequency as desired.
D. Press the Light (Decorative LED Lights) On/Off Button repeatedly to turn On/Off the Decorative LED Lights.
At the light on mode:
Press the“1”Button repeatedly to set or reset the color of the Decorative LED Lights to Red, Green or Blue.
Press the“2”–“6”Buttons to set or reset the blinking mode of the Decorative LED Lights.
5. When finished listening, press the POWER ON/OFF Button to OFF position to shut off the unit.
BT Mode:
BT (Bluetooth) pairing:
First time use or re-pairing the unit to a new BT Device, pair as follows:
1. Power on the unit and enter to BT mode as previously instructed.“bLUE BT”will appear on the display
and“BT”in it will blink. The unit also will sound a prompt“Enter to Bluetooth”.
2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen
instructions from the external BT Device. After paired, the unit will sound a prompt“Bluetooth connected”
and the BT Indicator will stop blinking.
3. If pairing is complete you may now play music and answer calls with your external BT Device.
4. During playback:
Press the ll Button on the unit to pause, press again to resume normal playback.
Press the l or l Buttons repeatedly to skip tracks.
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Normal operation after pairing:
Notes:
When the external BT Device searched the unit, our model number“MM438”
will appear on the display of external BT Device.
If while pairing you are asked for a code please try "0000" or "1234".
1. Power on the unit and enter to BT mode as previously instructed.“bLUE BT”will
appear on the display and“BT”in it will blink. The unit also will sound a prompt “Enter to Bluetooth”.
2. Wait a few seconds until the unit is automatically paired to the external BT Device. The unit will sound a
prompt“Bluetooth connected”and the BT Indicator will stop blinking.
3. After pairing is complete you may now play music and answer calls with your external BT Device.
5
Place the external BT device
close to the unit
Pair the external BT Device to
the unit as page 5
Reduce the volume level of the
connected/paired device
Reduce the volume level by turning the
MASTER VOL (Volume) Control Knob
counterclockwise
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
t
SD Card
1
23
45
22
6
7
8
9 10
11
13 14 15 16 17 18 19 20 21
23 23
AUX IN (Line in) “LINE”will appear on the display
Radio FM Band Radio frequency“XX.X”or
“XXX.X”will appear on the display
TF (If Micro SD Card inserted) Indicator“USB TF”on display will illuminate
USB (If USB Device inserted) Indicator“USB TF”on display will illuminate
BT (Bluetooth) “bLUE BT”will appear on the display
t
1 x Audio Connection Cable with 3.5mm Plugs

Produktspecifikationer

Varumärke: Magnavox
Kategori: högtalare
Modell: MM438

Behöver du hjälp?

Om du behöver hjälp med Magnavox MM438 ställ en fråga nedan och andra användare kommer att svara dig


högtalare Magnavox Manualer

Magnavox

Magnavox MSB2600 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MSB5300 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MSB5305 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MMA3683n Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MMA3629 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MD6949 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MMA3680 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MMA3685 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MMA3717 Bruksanvisning

8 Januari 2025
Magnavox

Magnavox MMA3679 Bruksanvisning

8 Januari 2025

högtalare Manualer

Nyaste högtalare Manualer

Heco

Heco CELAN GT 502 Bruksanvisning

9 Januari 2025
Heco

Heco INC 602 Bruksanvisning

9 Januari 2025
Yorkville

Yorkville Paraline PSA1 Bruksanvisning

9 Januari 2025
Boston Acoustics

Boston Acoustics VS 336 Bruksanvisning

9 Januari 2025
Electro-Voice

Electro-Voice XLE191-FG Bruksanvisning

9 Januari 2025
Electro-Voice

Electro-Voice Sx600 Bruksanvisning

9 Januari 2025
Klipsch

Klipsch ProMedia 2.1 Wireless Bruksanvisning

8 Januari 2025
Polk

Polk F/X 1000 Bruksanvisning

8 Januari 2025
QSC

QSC Wideline 10 WL2102-w Bruksanvisning

8 Januari 2025
RCF

RCF HDL 36-AS Bruksanvisning

8 Januari 2025