Metra 99-7882B Bruksanvisning
Läs nedan 📖 manual på svenska för Metra 99-7882B (8 sidor) i kategorin Bilsats. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/8
METRA. The World’s best kits.®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
REV. 11/14/2017 INST99-7882B
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
Installation instructions for part 99-7882B U.S. PATENT # D728,554
• ISO DIN radio provision with pocket
Note: This kit will not retain the i-MID display
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (3) metal panel clips • E) (3) plastic panel clips
• F) (4) #8 x 3/8” Phillips truss-head screws • G) (13) #8 x 3/8” Phillips pan-head screws
• H) (3) #4 x 3/8” Phillips truss-head screws • I) (2) #8 x 1/2” Phillips pan-head screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • Please visit metraonline.com for options
Antenna Adapter: • 40-HD11
• Panel removal tool • Phillips screwdriver • 8mm socket wrench
TOOLS REQUIRED
A B C D E
H
F
I
G
Dash Disassembly ..................................................2
Kit Preparation ........................................................3
Kit Assembly
– ISO DIN radio provision with pocket 3 ......................
Table of Contents
99-7882B
®
1.
Open the pocket door below the
radio, remove (2) Phillips screws
exposed, and then remove the
pocket. (Figure A)
2.
Remove (2) Phillips screws from the
bottom edge of the radio. (Figure B)
3. Remove (2) 8mm screws facing
up from inside the pocket cavity.
(Figure C)
4. Unsnap and remove the climate/
radio panel assembly. (Figure D)
5. Remove the components from the
climate/radio panel to be reused in
kit assembly. (Figure E)
a. Remove (4) screws from the
climate control panel.
b. Remove (2) screws from the
factory hazard button.
c. Remove (3) screws from the
factory vent.
d. Remove (3) screws from the
lower trim panel.
Continue to kit preparation
Dash Disassembly
(Figure E)
(Figure A)
(Figure B)
(Figure C)
(Figure D)
Step 5 a
Step 5 b
Step 5 c
Step 5 d
99-7882B
®
Kit Preparation Kit Assembly
(Figure A)
(Figure A)
(Figure B)
1.
Secure the factory components removed in dash disassembly to the . Except for the radio panel
(3) screws to secure the lower trim panel, either the factory screws or the (9) #8 x 3/8” Phillips
pan-head screws supplied with the kit may be used. For the lower trim panel use the (3)
#4 x 3/8” Phillips truss-head screws supplied with the kit to secure it to the panel. (Figure A)
2. Attach the (3) metal and (3) plastic panel clips to the . The factory metal radio panel
clips may be used in place of the metal clips, but not the plastic clips. (Figure A)
Continue to kit assembly
ISO DIN radio provision with pocket
1.
Secure the to the pocket radio brackets
with the (4) #8 x 3/8” Phillips pan-head
screws supplied with the kit. (Figure A)
2. Remove the metal DIN sleeve and
trim ring from the aftermarket radio.
3.
Slide the radio between the bracket/
pocket assembly
and secure it with the
screws supplied with the radio. (Figure B)
4. Secure the completed assembly to
the with the (4) #8 radio trim panel
X 3/8” Phillips truss-head screws
supplied with the kit. (Figure C)
5.
Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections
to the radio. Metra recommends
using the proper mating adapter from
Metra and/or AXXESS. Re-connect the
negative battery terminal and test the
radio for proper operation.
6.
Reassemble the dash in reverse order
of disassembly using the (2) #8 x 1/2”
Phillips pan-head screws supplied
with the kit for the lower radio mounts.
Metal clip locations
Plastic clip
location
Plastic clip
locations
Produktspecifikationer
| Varumärke: | Metra |
| Kategori: | Bilsats |
| Modell: | 99-7882B |
Behöver du hjälp?
Om du behöver hjälp med Metra 99-7882B ställ en fråga nedan och andra användare kommer att svara dig
Bilsats Metra Manualer
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
25 September 2024
Bilsats Manualer
- Bilsats Motorola
- Bilsats Nokia
- Bilsats Pioneer
- Bilsats Siemens
- Bilsats Alpine
- Bilsats Silvercrest
- Bilsats Nedis
- Bilsats Gembird
- Bilsats Pyle
- Bilsats Livoo
- Bilsats BeeWi
- Bilsats Caliber
- Bilsats Manhattan
- Bilsats Thule
- Bilsats Hama
- Bilsats Parrot
- Bilsats Maginon
- Bilsats Envivo
- Bilsats Uniden
- Bilsats Technaxx
- Bilsats Bury
- Bilsats T'nB
- Bilsats SuperTooth
- Bilsats Veho
- Bilsats Mr Handsfree
- Bilsats HQ
- Bilsats Scosche
- Bilsats PAC
- Bilsats Urban Revolt
- Bilsats Iluv
- Bilsats KRAM
- Bilsats NAV-TV
- Bilsats Ergotron
- Bilsats Havis
- Bilsats Kogan
- Bilsats Interphone-Cellularline
- Bilsats Arkon
- Bilsats I-Tec
- Bilsats Hamron
- Bilsats Brodit
Nyaste Bilsats Manualer
19 Oktober 2024
6 Oktober 2024
2 Oktober 2024
29 September 2024
25 September 2024
25 September 2024
23 September 2024
23 September 2024
23 September 2024
23 September 2024