Mikrotik LtAP Bruksanvisning

Mikrotik Inte kategoriserad LtAP

Läs nedan 📖 manual på svenska för Mikrotik LtAP (9 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/9

LtAP

LtAPLtAP

LtAP

The LtAP is a wireless access point with three SIM card slots for cellular data modems.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Read the installation instructions before connecting the system to the power source.

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for obtaining any

required local or national safety inspections of the structural integrity of the installation by the local authority/inspection department.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole but can also be installed indoors. Please read the mounting instructions carefully before

beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to

people and damage to the system.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 120 centimeters from your body, occupational user, or the

general public.

Quickstart

Please follow these quick steps to set up your device:

Unscrew two screws and remove doors to access all ports. Please see the section.Mounting

Connect your Internet cable to the Ethernet port (this is optional if using LTE as the primary connection).

Install your modem see slot usage (optional).miniPCIe

Insert the SIM card into the slot (optional) (see ).SIM card

Connect GPS antenna (optional).

Mount unit in your desired place, please see paragraph.Mounting

Choose your powering solution, please see the section for possibilities.Powering

Download the WinBox configuration tool ;https://mt.lv/winbox

There is no default IP address set, user name: and there is no password (or, for some models, check user and wireless passwords on the 

admin



sticker), usetheNeighborstab and connect through the MAC address;

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability.

Choose your country, to apply country regulation settings, and set up your password on the screen that loads.

Set the to indoors or outdoors, depending on the usage type.

Installation



*The following RouterOS "npk" packages are required for the core functionality of the product: gps, system.

Extension slots and ports

Built-in 2 GHz wireless access point module, AP/station/bridge/p2p modes are supported. Onboard PIF antennas built-in, as well as MMCX

connectors for external antennas (software selectable).

Two miniPCIe slots and three SIM slots.

Built-in GPS module with an external SMA connector. Supports -GPS, GLONASS, BeiDou, Galileo).

Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for

connecting to other network devices. The Ethernet port accepts 12-30 V DC powering from a passive PoE injector.

One DB9 RS232 serial port for serial console access. Configured as 115200 bit/s, 8 data bits, 1 stop bit, no parity.

One USB 2.0 port for storage devices or cellular modems.

Mounting

It is possible to attach the device to a wall, using the provided four screws and designed four holes on the unit.

The ports are protected with a small door, that is held in place with two screws. Remove to access Ethernet ports, antenna connector, SIM slots,

etc.

The door has cut-out places for all available ports, so you can guide through all necessary cables, but please only break out the openings that you

will use.

Several places for external antennas are provided on the case, use an appropriate size drill, to make them available. Be careful and measure the

chosen antenna, so that it does not touch the internal PCB board when installed.

The device can be used both indoors and outdoors. The IP rating scale of IP54.

If you intend to mount outdoors, please ensure that any cable openings are directed downwards. The Mounting direction is indicated on the device with an

arrow pointing up. Use POE injector and proper grounding. Recommended using Cat6 shielded cable.

Warning! This equipment should be installed and operated with a minimum distance of 30 cm between the device and your body. Operation of this

equipment in the residential environment could cause radio interference.

Configuration

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and

stability. RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself

accustomed to the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to https://mt.lv/help https://mt.lv/winbox

the MAC address of the device from the LAN side (all access is blocked from the internet port by default). For recovery purposes, it is possible to boot the

device from a network, see the section .Reset button

GPS