Mikrotik wAP LTE kit Bruksanvisning

Mikrotik Inte kategoriserad wAP LTE kit

Läs nedan 📖 manual på svenska för Mikrotik wAP LTE kit (11 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/11

wAP kit-series

wAP kit-serieswAP kit-series

This manual is for wAP kit series models:

This manual is for wAP kit series models:This manual is for wAP kit series models:

wAP LTE kit

wAP LTE kit US

wAP 4G kit

This device needs to be upgraded to RouterOS v6.44.6 or the latest version to ensure compliance with local authority regulations.

Note. The information contained here is subject to change. Please visit the product page on

www.mikrotik.com for the most up to date version of this

document.

Safety Warnings

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole but can also be installed indoors. Please read the mounting instructions carefully before

beginning installation. Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to

people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:This MikroTik equipment complies with the FCC, IC, and European Union radiation exposure limits set forth for an

uncontrolled environment.This MikroTik device should be installed and operated no closer than 38 centimeters from your body, occupational user, or the

general public.

Quickstart

Use a Phillips head screwdriver to loosen the screw, which secures the bottom lid (see ).Bottom Lid

Insert the SIM card.

Choose your powering solution, please see the section for possibilities.Powering

Connect the Ethernet cable to the PoE and connect the other end of the Ethernet cable to this MikroTik router. Plug the provided power supply

into the PoE injector.

Wireless AP mode is enabled by default, you can connect from your computer to the SSID that begins with "MikroTik". The configuration interface

is available via a web browser. The address is .https://192.168.88.1

Connect to the wireless network, open in your web browser to start the configuration.https://192.168.88.1

User name: a and there is no password by default you will be logged in automatically to the Quick Set screen

dmin

(or, for some models, check

.user and wireless passwords on the sticker)

Click the "Check for updates" button on the right side and updating your RouterOS software to the latest version to ensure the best performance

and stability. Must have a valid SIM card inserted.

To personalize your wireless network, SSID can be changed in the fields "Network Name";

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings.

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols.

Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next

time.

Click on the "Apply Configuration" to save changes.

To manually update the device if no Internet connection is available.

Download the latest RouterOS software from .https://mikrotik.com/download

Choose MIPSBE packages, and save them to your PC.

Connect again and in menu upload downloaded packages.

Files

Restart the device.

MikroTik mobile app

Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point.

Scan QR code and choose your preferred OS.