Milwaukee 6470-21 Bruksanvisning

Milwaukee Sågmaskin 6470-21

Läs nedan 📖 manual på svenska för Milwaukee 6470-21 (36 sidor) i kategorin Sågmaskin. Denna guide var användbar för 13 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/36

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

To reduce The risk of injury, user musT read operaTor's manual.

afin de réduire le risque de blessures, l'uTilisaTeur doiT lire le manuel de

l'uTilisaTeur.

para reducir el riesgo de lesiones, el usuario debe leer el manual del

operador.

Cat. No.

No de cat.

6470-21

10¼" CIRCULAR SAw

SCIE CIRCULAIRE 260 mm (10¼")

SIERRA CIRCULAR DE 260 mm (10¼")

GENERAL POWER TOOL SAFETY WARNINGS

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to

follow the warnings and instructions may result in electric shock, re and/or serious injury. Save

all warnings and instructions for future reference. The term “power tool” in the warn-

ings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

PERSONAL SAFETY

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while oper-

ating a power tool. Distractions can cause you to

lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodied plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

result in personal injury.

• Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery

or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused

by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

SERVICE

• Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

Cutting procedures

• DANGER: Keep hands away from cutting

area and the blade. Keep your second hand on

auxiliary handle, or motor housing. If both hands

are holding the saw, they cannot be cut by the blade.

• Do not reach underneath the workpiece. The

guard cannot protect you from the blade below the

workpiece.

• Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

• Never hold piece being cut in your hands or

across your leg. Secure the workpiece to a stable

platform. It is important to support the work properly

to minimize body exposure, blade binding, or loss

of control.

• Hold the power tool by insulated gripping sur-

faces only, when performing an operation where

the cutting tool may contact hidden wiring or its

own cord. Contact with a “live” wire will also make

exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• When ripping, always use a rip fence or straight

edge guide. This improves the accuracy of cut and

reduces the chance of blade binding.

• Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades

that do not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

• Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance

and safety of operation.

Further safety instructions for all saws

Kickback causes and related warnings

– Kickback is a sudden reaction to a pinched, bound

or misaligned saw blade, causing an uncontrolled

saw to lift up and out of the workpiece toward the

operator;

– When the blade is pinched or bound tightly by the

kerf closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the

operator;

– If the blade becomes twisted or misaligned in the

cut, the teeth at the back edge of the blade can dig

into the top surface of the wood causing the blade

to climb out of the kerf and jump back toward the

operator.

Kickback is the result of saw misuse and/or incor-

rect operating procedures or conditions and can be

avoided by taking proper precautions as given below:

• Maintain a rm grip with both hands on the saw

and position your arms to resist kickback forces.

Position your body to either side of the blade, but

not in line with the blade. Kickback could cause

the saw to jump backwards, but kickback forces can

be controlled by the operator, if proper precautions

are taken.

• When blade is binding, or when interrupting a

cut for any reason, release the trigger and hold

the saw motionless in the material until the

blade comes to a complete stop. Never attempt

to remove the saw from the work or pull the saw

backward while the blade is in motion or kick-

back may occur. Investigate and take corrective

actions to eliminate the cause of blade binding.

• When restarting a saw in the workpiece, centre

the saw blade in the kerf and check that saw

teeth are not engaged into the material. If saw

blade is binding, it may walk up or kickback from the

workpiece as the saw is restarted.

• Support large panels to minimise the risk of

blade pinching and kickback. Large panels tend

to sag under their own weight. Supports must be

placed under the panel on both sides, near the line

of cut and near the edge of the panel.

• Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf caus-

ing excessive friction, blade binding and kickback.

• Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If

blade adjustment shifts while cutting, it may cause

binding and kickback.

• Use extra caution when sawing into existing

walls or other blind areas. The protruding blade

may cut objects that can cause kickback.

Lower guard function

• Check lower guard for proper closing before

each use. Do not operate the saw if lower guard

does not move freely and close instantly. Never

clamp or tie the lower guard into the open posi-

tion. If saw is accidentally dropped, lower guard may

be bent. Raise the lower guard with the retracting

handle and make sure it moves freely and does not

touch the blade or any other part, in all angles and

depths of cut.

• Check the operation of the lower guard spring.

If the guard and the spring are not operating

properly, they must be serviced before use.

Lower guard may operate sluggishly due to dam-

aged parts, gummy deposits, or a build-up of debris.

• Lower guard should be retracted manually only

for special cuts such as “plunge cuts” and

“compound cuts.” Raise lower guard by retracting

handle and as soon as blade enters the material, the

lower guard must be released. For all other sawing,

the lower guard should operate automatically.

• Always observe that the lower guard is covering

the blade before placing saw down on bench or

oor. An unprotected, coasting blade will cause

the saw to walk backwards, cutting whatever is in

its path. Be aware of the time it takes for the blade

to stop after switch is released.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause can-

cer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to lter out microscopic particles.

Produktspecifikationer

Varumärke:	Milwaukee
Kategori:	Sågmaskin
Modell:	6470-21

Behöver du hjälp?

Om du behöver hjälp med Milwaukee 6470-21 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Sågmaskin Milwaukee Manualer

Milwaukee M12 2420-21 Bruksanvisning

6 Oktober 2024

Milwaukee M12 JS-402B Bruksanvisning

3 Oktober 2024

Milwaukee M18 FTCHS14 Bruksanvisning

26 September 2024

Milwaukee MXF COSCG2 Bruksanvisning

26 September 2024

Milwaukee MSUV280 Bruksanvisning

23 September 2024

Milwaukee M18 BJS Bruksanvisning

21 September 2024

Milwaukee SCS 65 Q Bruksanvisning

21 September 2024

Milwaukee M12 BS Bruksanvisning

21 September 2024

Milwaukee M18 FMCS66 Bruksanvisning

21 September 2024

Milwaukee M18 BSX Bruksanvisning

21 September 2024

Sågmaskin Manualer

Nyaste Sågmaskin Manualer

Hikoki C 6BU3 Bruksanvisning

27 Oktober 2024

Dedra DED7060 Bruksanvisning

27 Oktober 2024

Einhell KGS 190 Bruksanvisning

27 Oktober 2024

Sun Joe SWJ599E Bruksanvisning

27 Oktober 2024

McCulloch CSE1935S Bruksanvisning

27 Oktober 2024

Hikoki C10FSB Bruksanvisning

27 Oktober 2024

Metabo STA 18 LTX 150 BL Bruksanvisning

26 Oktober 2024

Craftsman 917.377662 Bruksanvisning

26 Oktober 2024

Maruyama MCV51 Bruksanvisning

26 Oktober 2024

Powerplus POWX53300T Bruksanvisning

22 Oktober 2024