Milwaukee M18 2602-20 Bruksanvisning

Milwaukee Borrmaskin M18 2602-20

Läs nedan 📖 manual på svenska för Milwaukee M18 2602-20 (11 sidor) i kategorin Borrmaskin. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/11

M18™1/2" HAMMER-DRILL

PERCEUSE À PERCUSSION DE M18™ 13 mm (1/2")

TALADRO DE PERCUSIÓN Y DE 13 mm (1/2") M18™

Cat. No.

No de cat.

2602-20

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

FUNCTIONAL DESCRIPTION

SYMBOLOGY

ASSEMBLY

WARNING Recharge only with the

charger specified for the battery. For spe-

ciﬁ c charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

SPECIFICATIONS

Installing the Side Handle

1. To install the side handle,

loosen the side handle grip

until the hooks are far enough

apart to ﬁ t into the slots on

the gear case ring. Posi-

tion the side handle on the

top of the tool, pointing left

or right. Tighten the side

handle grip until it is secure.

2. To remove the side handle,

loosen the side handle grip

until the side handle can be

removed. Reposition and tighten securely.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely. Ensure side

handle is tightened securely before each use.

Volts

Direct Current

No Load Revolutions per

Minute (RPM)

CUS Underwriters Laboratories, Inc.

United States and Canada

Cat. No. Volts

DC No Load

RPM

No Load

Blows

per Minute

Capacities

Steel

Wood

MasonryFlat Bit Auger Bit Hole Saw Screws (dia.)

2602-20 18 Low 0-550

High 0-1700

Low 0-9350

High 0-29,000

1/2” 1-1/2" 1" 2-1/8" 1/4" 5/8"

1. Trigger

2. Control switch

3. LED

4. Keyless chuck

5. Torque selector collar

6. Application selector collar

7. Speed selector

Hooks

Slots

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure

to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury. Save all warnings and instructions for future reference. The term "power

tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

BATTERY TOOL USE AND CARE

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery terminals

together may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

•

Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping

surfaces, when performing an operation

Using Keyless Chucks

This tool is equipped with a spindle lock. The chuck

can be tightened with one hand, creating higher grip

strengths on the bit.

Always remove the battery pack or lock the trigger

before inserting or removing bits.

1. To open the chuck jaws, turn the sleeve in the

counterclockwise direction.

When using drill bits, allow the bit to strike the

bottom of the chuck. Center the bit in the chuck

jaws and lift it about 1/16" o of the bottom.

When using screwdriver bits, insert the bit far

enough for the jaws to grip the hex of the bit.

2. To close the chuck jaws, turn the sleeve in the

clockwise direction. The bit is secure when the

chuck makes a ratcheting sound and the sleeve

can not be rotated any further.

3. To remove the bit, turn the sleeve in the coun-

terclockwise direction.

NOTE: A ratcheting sound may be heard when the

chuck is opened or closed. This noise is part of the

locking feature, and does not indicate a problem

with the chuck’s operation.

Selecting Speed

The speed selector is on top of the motor housing.

Allow the tool to come to a complete stop before

changing speeds. See “Applications” for recom-

mended speeds under various conditions.

1. For Low speed (up to 450 RPM), push the speed

selector to display “1”.

2. For High speed (up to 1700 RPM), push the

speed selector to display “2”.

Selecting Hammer, Drill or Drive Action

MILWAUKEE Hammer-Drills have three operating

modes: drilling with hammering action, drilling only,

and driving screws. To set the operating mode,

rotate the application selector collar and torque

selector collar to the desired symbols.

1. To use the hammer-drilling mode, rotate

the application selector collar until the hammer

symbol appears in line with the arrow. Ap-

ply pressure to the bit to engage the hammering

mechanism.

Torque selector

collar setting

Torque

1 - 5 0 - 16 in. lbs.

6 - 10 17 - 27 in. lbs.

11 - 15 28-37 in. lbs.

16 - 20 38-46 in. lbs.

21-24 47-60 in. lbs.

Drill

1 Low

2 High

550 in. lbs. *

150 in. lbs.

Fig. 1

To Hammer

Fig. 2

To Drill

Fig. 3

To Drive Screws

OPERATION

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side shields.

Using Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow

the motor to come to a complete stop before using

the control switch.

Fig. 4

Push for

Forward

Push for

Reverse

PUSH TO CENTER TO LOCK

For forward (clockwise) rotation, push in the control

switch from the right side of the tool. Check the

direction of rotation before use.

For reverse (counterclockwise) rotation, push in the

control switch from the left side of the tool. Check

direction of rotation before use.

To lock the trigger, push the control switch to the

center position. The trigger will not work while

the control switch is in the center locked position.

Always lock the trigger or remove the battery

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle ﬁ rmly and pull

the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To stop the tool, release the trigger. Make sure

the bit comes to a complete stop before laying

the tool down.

Drilling

Place the bit on the work surface and apply ﬁ rm

pressure before starting. Too much pressure will

slow the bit and reduce drilling efﬁ ciency. Too little

pressure will cause the bit to slide over the work

area and dull the point of the bit.

If the tool begins to stall, reduce pressure slightly

to allow the bit to regain speed. If the bit binds,

reverse the motor to free the bit from the workpiece.

NOTE: The number selected on the torque collar

has no eect on operation of the drill in hammer

mode. NOTE: When using carbide bits, do not

use water to settle dust. Do not attempt to drill

through steel reinforcing rods. This will damage

the carbide bits.

2. To use the drilling only mode, rotate the ap-

plication selector collar until the drill symbol

appears in line with the arrow.

NOTE: The number selected on the torque collar

has no eect on operation of the drill in drilling

mode.

3. To use the driving screws mode rotate the

application selector collar until the drive symbol

appears in line with the arrow. Then rotate

the torque selector collar until the desired clutch

setting appears in line with the arrow.

The adjustable clutch, when properly adjusted, will

slip at a preset torque to prevent driving the screw

too deep into different materials and to prevent

damage to the screw or tool.

The torque speciﬁ cations shown here are ap-

proximate values.

* Max developed torque when using Milwaukee XC

battery pack.

NOTE: Because the above settings are only a

guide, use a piece of scrap material to test the dif-

ferent clutch positions before driving screws into

the workpiece.

APPLICATIONS

WARNING To reduce the risk of elec-

tric shock, check work area for hidden pipes

and wires before drilling or driving screws.

ﬂ ow of dust indicates the proper drilling rate. Do not

let the bit spin in the hole without cutting. Do not

use water to settle dust or to cool bit. Both actions

will damage the carbide.

Driving Screws and Nut Running

Drill a pilot hole when driving screws into thick or

hard materials. Select the driving screws mode.

Set the torque selector collar to the proper position

and set the speed to low. Use the proper style and

size screwdriver bit for the type of screw you are

using. With the screwdriver bit in the screw, place

the tip of the screw on the workpiece and apply ﬁ rm

pressure before pulling the trigger. Screws can be

removed by reversing the motor.

Overloading

Continuous overloading may cause permanent

damage to tool or battery pack.

Bit Binding

A high rotational force occurs when a bit binds. If

the bit binds, the tool will be forced in the opposite

direction of the bit rotation. Bits may bind if they are

misaligned or when they are breaking through a

hole. Wood boring bits can also bind if they run into

nails or knots. Be prepared for bit binding situations.

To reduce the chance of bit binding:

• Use sharp bits. Sharp bits are less likely to bind

when drilling.

• Use the proper bit for the job. There are bits that

are designed for speciﬁ c purposes.

• Use caution when drilling pitchy, knotty, wet or

warped material or when drilling in material that

may contain nails.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely. Ensure side

handle is tightened securely before each use.

pack before performing maintenance, changing

accessories, storing the tool and any time the tool

is not in use.

Drilling in Wood, Composition Materials and

Plastic

When drilling in wood, composition materials and

plastic, select the drill-only operating mode.

Start the drill slowly, gradually increasing speed as

you drill. When drilling into wood, use wood augers

or twist drill bits. Always use sharp bits. When using

twist drill bits, pull the bit out of the hole frequently

to clear chips from the bit ﬂ utes. To reduce the

chance of splintering, back work with a piece of

scrap wood. Select low speeds for plastics with a

low melting point.

Drilling in Metal

When drilling in metal, select the drill-only

operating mode. Use high speed steel twist drills

or hole saws. Use a center punch to start the hole.

Lubricate drill bits with cutting oil when drilling in iron

or steel. Use a coolant when drilling in nonferrous

metals such as copper, brass or aluminum. Back

the material to prevent binding and distortion on

breakthrough.

Drilling in Masonry

When drilling in masonry, select the hammer-

drill operating mode. Use high speed carbide-tipped

bits. Drilling soft masonry materials such as cinder

block requires little pressure. Hard materials like

concrete require more pressure. A smooth, even

Produktspecifikationer

Varumärke:	Milwaukee
Kategori:	Borrmaskin
Modell:	M18 2602-20

Behöver du hjälp?

Om du behöver hjälp med Milwaukee M18 2602-20 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Borrmaskin Milwaukee Manualer

Milwaukee M18 Fuel Super Hawg 2709-22 Bruksanvisning

8 Oktober 2024

Milwaukee M18 FPD Bruksanvisning

1 Oktober 2024

Milwaukee 5376-20 Bruksanvisning

30 September 2024

Milwaukee M18 FHACOD32 Bruksanvisning

23 September 2024

Milwaukee M18 ONEFHP Bruksanvisning

23 September 2024

Milwaukee M18 ONEFH Bruksanvisning

23 September 2024

Milwaukee M18 CHM Bruksanvisning

23 September 2024

Milwaukee M18 FHM Bruksanvisning

23 September 2024

Milwaukee M18 ONEDD3 Bruksanvisning

22 September 2024

Milwaukee SB 2-35 D Bruksanvisning

21 September 2024

Borrmaskin Manualer

Nyaste Borrmaskin Manualer

Black And Decker PF126 Bruksanvisning

27 Oktober 2024

Bosch GSR 120-LI Professional Bruksanvisning

24 Oktober 2024

Bosch gsr 18 2 li Bruksanvisning

23 Oktober 2024

Vonroc CD510DC Bruksanvisning

21 Oktober 2024

Einhell TC-CD 18/35 Li Bruksanvisning

20 Oktober 2024

Einhell Herocco Solo Bruksanvisning

19 Oktober 2024

DeWalt dc987ka Bruksanvisning

19 Oktober 2024

AEG KH 28 Super XE Bruksanvisning

18 Oktober 2024

MSW -DDM255 Bruksanvisning

16 Oktober 2024

MSW -DDM152 Bruksanvisning

16 Oktober 2024