Mtx Audio RoadThunder RT602 Bruksanvisning

Mtx Audio mottagare RoadThunder RT602

Läs nedan 📖 manual på svenska för Mtx Audio RoadThunder RT602 (44 sidor) i kategorin mottagare. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/44

RT602

2 Channel Class-AB Power Ampliﬁer

180W

RMS

www.mtx.eu.com

www.mtx.com

SPEAKER

BRIDGE

R+

R- L+ L-

GND REM +12V FUSE

POWER

LINE OUT LINE IN

HLI

+ R - G - L +

GAIN X-OVER LPFHPFR

6V 0,1V 40Hz 400Hz

FULL

HPF LPF 40Hz 400Hz

www.mtx.com - www.mtx.eu.com

Owner’s Manual - RT602

Introduction

Thank you for purchasing an MTX Audio Hi-Performance amplier. Proper installation matched with MTX speak-

ers and subwoofers provide superior sound and performance for endless hours of waking the neighbors, slam-

min' your friends or at out stomping wanna-be players. Congrats and enjoy the ultimate audio experience with

MTX !

Specications :

• 2-Channel Class-AB Amplier

• CEA2006 certied Power Output :

- 90 watts RMS x 2-channel at 2 ohm and THD+N ≤1%

- 60 watts RMS x 2-channel at 4 ohm and THD+N ≤1%

- 180 watts RMS x 1-channel at 4 ohm and THD+N ≤1%

• Crossover :

- High pass 12dB/oct variable from 40Hz to 400Hz

- Low pass 12dB/oct variable from 40Hz to 400Hz

• Signal-to-Noise Ratio (1 watt) : > 80dB

• THD+Noise (Distortion) (1 watt) : ≤ 1%

• Frequency Response (±1dB) : 20Hz-30000Hz

• Maximum Input Signal : 6V

• Maximum Sensitivity : 100mV

• Dimensions : 310mm x 180mm x 55mm

• High level inputs

Control Panel

Control Panel :

Gain Control (GAIN) : The gain control matches the input sensitivity of the amplier to the source unit being used.

The operating range varies from 100mv to 6V.

Adjusting the gain

1. Turn the gain control on the amplier all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the amplier until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The amplier is now calibrated to the output of the source unit.

Low-Pass High-Pass X-Over Switch (X-OVER) :

In “LPF” position, the active low pass (LP) x-over is turned on

In “HPF” position, the active high pass (HP) x-over is turned on

In “FULL” position, the x-over is turned o

High Pass X-Over Frequency Control (HPF) :

Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..

Low Pass X-Over Frequency Control (LPF) :

Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..

RCA Inputs (LOW INPUT) : These RCA inputs are used with source units that have RCA or Line level outputs.

(Source units need a minimum level of 100mV output for proper operation of the amplier).

MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-

ated noise entering the system.

RCA outputs - These RCA output jacks are for connecting multiple ampliers to 1 stereo RCA lead coming

from the source unit (daisy chaining).

PowerOn/Protection LED - The LED illuminates red when the amp is switched on. When the amps is in shortcir-

cuit or thermal protection, the LED is blinking.

Speaker level inputs (HLI) :

This input will allow the amplier to operate from source units with speaker-level outputs. Output speaker leads

from the source unit should be tied directly to the wire harness provided with the amplier.

Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.

(+12V) Power Terminal : This is the main power input for the amplier and must be connected directly to the posi-

tive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable in the

vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to massive

currents that can induce noise into the audio system. It is also very important to have a tight, secure connection

for maximum performance. MTX recommends using 10mm

2 power wire with the MTX RT602 amplier.

Remote Terminal (REM) : The amplier can be turned on by applying 12 volts to this terminal. Typically this volt-

age is supplied by a wire from the source unit marked “remote” or “power antenna”.

Ground Terminal (GND) : A proper ground is required for your amplier to operate at peak performance. A short

ground cable the same diameter as the power cable should be used to attach the ground terminal directly to

the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be

attached.

Speaker Terminals (SPEAKER) : Connect speakers to these terminals. Observe speaker polarity throughout the

system. Improper phase can result in loss of bass response and/or poor overall sound quality.

Bridge Mode : When bridging the amplier, use the right positive terminal and the left negative terminal only.

Warning : do not bridge the amplier with an impedance lower than 4 ohm.

Fuse (FUSE) : When fuse blow, replace them with the same value. Never use a higher rated fuse !

Produktspecifikationer

Varumärke:	Mtx Audio
Kategori:	mottagare
Modell:	RoadThunder RT602
Färg på produkten:	Black, Stainless steel
Inbyggd display:	Ja
Vikt:	4380 g
Bredd:	350 mm
Djup:	188 mm
Höjd:	385 mm
Tillgångar:	500 W
På / Av knapp:	Ja
Hållbarhetscertifikat:	CE
Omvänd:	Ja
Knivmaterial:	Roestvrijstaal
AC-ingångsspänning:	230 V
AC-ingångsfrekvens:	50 Hz
Worsthoorn:	Ja
Kebbe-makare:	Ja
Maximal effekt blockerad (motor):	1000 W