Netgear CG3300D Bruksanvisning

Netgear Inte kategoriserad CG3300D

Läs nedan 📖 manual på svenska för Netgear CG3300D (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
)NSTALLATION'UIDE
Euro-Docsis 3.0 Wireless Cable Modem Gateway CG3300D
Package Contents
• Gateway
• Power adapter
• Vertical stand (recommended)
• Ethernet cable
• Installation Guide (this guide)
Start Here
Estimated installation time: 15 to 30 minutes.
You will need a computer with DHCP enabled and an available Ethernet port.
Installation
Follow these quick steps to install your gateway.
1. For better wireless performance, insert the
gateway into the stand as shown.
2. Connect the gateway. Use the coaxial cable provided by your cable company to
connect the cable port (A) to your cable outlet.
3. Connect your computer to the cable modem gateway with an Ethernet cable (B).
A
B
4. Attach the power adapter cable to the gateway and plug it into an electrical outlet.
Make sure that the Power button on the rear panel is in the On position.
After the gateway is connected and power is applied, the gateway automatically
attempts to do the following:
• Scan and lock the downstream frequency, and then link back in upstream
direction.
• Obtain an IP address for the gateway itself. Then the gateway assigns an IP
address for the connected PC.
• Connect to the Internet.
5. Wait about two minutes for the LEDs to stop blinking. Then verify the following:
The Power LED is solid green.
The Downstream and Upstream LEDs are lit.
The Internet LED is solid green, indicating a link has been established to the
Internet.
The LAN LED is lit that corresponds et port where you to the local Ethern
connected your computer.
For more information, see the LED table on the other side of this document.
Power button
Warning: Do not install this device on top of
any other electrical equipment or install any other
equipment on top of this device. Keep this device
away from any heat sources such as direct
sunlight, heaters, radiators, or other A/V
receivers or devices that emit heat.
This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste
Electrical and Electronic Equipment (the WEEE Di
rective). If disposed of
within the European
Union, this product should be treated and recycled in accordance with the laws of your jurisdiction
implementing the WEEE Directive.
© 2009 by NETGEAR, Inc. All rights reserved. NETGEAR and the NETGEAR logo are registered trademarks
of NETGEAR, Inc. in the United States
and/or other countries. Other brand
and product names are trademarks or
registered trademarks of their respective holders. Information is subject to change without notice.
Do not stack or place near
heat source
June 2009
LED Description
Power
• Solid green. Power is supplied to the gateway.
• Solid amber. Power has been cut off due to overheating. Make sure
the gateway’s ventilation is not blocked. When the gateway cools
down, power cycle the gateway.
• Flashing amber. New firmware is updating
• Off. No power.
Downstream
• Solid green. The gateway is synchronized, and all four channels are
in use (channel bonding).
• Flashing. The gateway is scanning for a downstream DOCSIS
channel.
• Off. No downstream channels are locked.
Upstream
• Solid green. The gateway is synchronized, and all four channels are
in use (channel bonding).
• Flashing. The gateway is ranging to set up an upstream channel.
• Off. No upstream channels have been established.
Internet
• Solid green. The gateway is online.
• Flashing. The gateway is establishing its link to the Internet.
• Off. The gateway is offline.
LAN (Ethernet)
• Green indicates 1,000 Mbps. Amber indicates 10/100 Mbps.
• Solid. An Ethernet device is connected and powered on.
• Flashing. Data is being transmitted or received on the Ethernet port.
• Off. No Ethernet device is detected on the Ethernet port.
Button Description
Wireless
On/Off
Turn the wireless radio in the gateway on and off. The wireless radio is
on by default. The LED located below this button indicates if the wire-
less radio is on or off.
Push 'N'
Connect (WPS)
Pushing this button opens a 2-minute window for the gateway to con-
nect with other WPS-enabled devices. For more information, about
using WPS, select Documentation from the main menu and then see
the on-line User Manual.
Troubleshooting
• You can use the LEDs on the front of the gateway to determine the status of the
gateway and your Internet connection. If you cannot connect to the Internet, view the
LEDs to make sure that all connections are secure and power is supplied.
• There is a Power button on the rear panel of the gateway. This button must be in the
On position when the gateway is in use.
• You can return the gateway to its factory settings. On the bottom of the gateway, press
and hold the Restore Factory Settings button for over 7 seconds. The gateway
resets, and returns to its factory settings.
Technical Support
Thank you for choosing a NETGEAR product. Please call your Cable Internet Service
Provider for technical support. You may also take advantage of NETGEAR technical
support resources such as the NETGEAR online knowledge base at:
http://kbserver.netgear.com.
Defective or damaged merchandise should be returned to your point-of-purchase
representative. This information supersedes all support information printed on any
NETGEAR packaging or documentation.
Note to CATV System Installer
Please call the CATV systems installer’s attention to section 820-93 of the National
Electric Code which provides guidelines for proper grounding of this device. In particular,
section 820-93 specifies that the coaxial cable shield must be connected to the grounding
system of the building, as close to the point of cable entry as practical.
Warning: When installing or realigning an outside antenna system, take extreme care to
avoid any contact with the power lines or circuits. Contact with them could be fatal.
Reference to the Grounding Figure
The numbers in the figure on the right indicate:
1. Electric service equipment
2. Power service grounding electrode system
(NEC Art 250, Part H)
3. Ground clamps
4. Grounding conductors (NEC Section 810-21)
5. Antenna discharge unit (NEC Section 810-20)
6. Ground clamp
7. Antenna lead-in wire

Produktspecifikationer

Varumärke: Netgear
Kategori: Inte kategoriserad
Modell: CG3300D

Behöver du hjälp?

Om du behöver hjälp med Netgear CG3300D ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad Netgear Manualer

Netgear

Netgear FV318 Bruksanvisning

14 Oktober 2024
Netgear

Netgear Nighthawk X6S R7960P Bruksanvisning

13 Oktober 2024
Netgear

Netgear ProSafe AX743 Bruksanvisning

6 Oktober 2024
Netgear

Netgear JGS516 Bruksanvisning

4 Oktober 2024
Netgear

Netgear XS508M Bruksanvisning

2 Oktober 2024
Netgear

Netgear GS108Ev4 Bruksanvisning

1 Oktober 2024
Netgear

Netgear ProSafe AXM762 Bruksanvisning

1 Oktober 2024
Netgear

Netgear VPN01L Bruksanvisning

28 September 2024
Netgear

Netgear Orbi RBE972SB Bruksanvisning

26 September 2024
Netgear

Netgear Orbi RBK652S Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024