Onkyo TX-SR600 Bruksanvisning

Onkyo mottagare TX-SR600

Läs nedan 📖 manual på svenska för Onkyo TX-SR600 (80 sidor) i kategorin mottagare. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/80

Contents

Thank you for purchasing the Onkyo AV Receiver.

Please read this manual thoroughly before making

connections and plugging in the unit. Following the

instructions in this manual will enable you to obtain

optimum performance and listening enjoyment from

your new AV Receiver. Please retain this manual for

future reference.

TX-SR700

TX-SR600

Appendix 76

Remote controller 63

Setup and operation 36

Before using 2

AV Receiver

Instruction Manual

Facilities and connections 8

1. Read Instructions – All the safety and operating instructions

should be read before the appliance is operated.

2. Retain Instructions – The safety and operating instructions

should be retained for future reference.

3. Heed Warnings – All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions

should be followed.

5. Cleaning – Unplug the appliance from the wall outlet before

cleaning. The appliance should be cleaned only as recom-

mended by the manufacturer.

6. Attachments – Do not use attachments not recommended by

the appliance manufacturer as they may cause hazards.

7. Water and Moisture – Do not use the appliance near water –for

example, near a bath tub, wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories – Do not place the appliance on an unstable cart,

stand, tripod, bracket, or table. The appliance may fall, causing

serious injury to a child or adult, and serious damage to the

appliance. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the appliance.

Any mounting of the appliance should follow the

manufacturer’s instructions, and

should use a mounting accessory

recommended by the manufac-

turer.

9. An appliance and cart combina-

tion should be moved with care.

Quick stops, excessive force, and

uneven surfaces may cause the

appliance and cart combination to

overturn.

10. Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the appliance

and to protect it from overheating, and these openings must not

be blocked or covered. The openings should never be blocked

by placing the appliance on a bed, sofa, rug, or other similar

surface. The appliance should not be placed in a built-in instal-

lation such as a bookcase or rack unless proper ventilation is

provided. There should be free space of at least 20 cm (8 in.)

and an opening behind the appliance.

11. Power Sources – The appliance should be operated only from

the type of power source indicated on the marking label. If you

are not sure of the type of power supply to your home, consult

your appliance dealer or local power company.

12. Grounding or Polarization – The appliance may be equipped

with a polarized alternating current line plug (a plug having one

blade wider than the other). This plug will fit into the power

outlet only one way. This is a safety feature. If you are unable to

insert the plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to replace

your obsolete outlet. Do not defeat the safety purpose of the

polarized plug.

13. Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention

to cords at plugs, convenience receptacles, and the point where

they exit from the appliance.

14. Outdoor Antenna Grounding – If an outside antenna or cable

system is connected to the appliance, be sure the antenna or

cable system is grounded so as to provide some protection

against voltage surges and built-up static charges. Article 810

of the National Electrical Code, ANSI/NFPA 70, provides in-

formation with regard to proper grounding of the mast and sup-

porting structure, grounding of the lead-in wire to an antenna-

discharge unit, size of grounding conductors, location of an-

tenna-discharge unit, connection to grounding electrodes, and

requirements for the grounding electrode. See Figure 1.

15. Lightning – For added protection for the appliance during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and discon-

nect the antenna or cable system. This will prevent damage to

the appliance due to lightning and power-line surges.

16. Power Lines – An outside antenna system should not be lo-

cated in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines

or circuits. When installing an outside antenna system, extreme

care should be taken to keep from touching such power lines or

circuits as contact with them might be fatal.

17. – Do not overload wall outlets, extension cords,Overloading

or integral convenience receptacles as this can result in a risk

of fire or electric shock.

18. Object and Liquid Entry – Never push objects of any kind

into the appliance through openings as they may touch danger-

ous voltage points or short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind on the appliance.

19. Servicing – Do not attempt to service the appliance yourself as

opening or removing covers may expose you to dangerous volt-

age or other hazards. Refer all servicing to qualified service

personnel.

20. Damage Requiring Service – Unplug the appliance form the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

A. When the power-supply cord or plug is damaged,

B. If liquid has been spilled, or objects have fallen into the

appliance,

C. If the appliance has been exposed to rain or water,

D. If the appliance does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper ad-

justment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the appliance to its normal operation,

E. If the appliance has been dropped or damaged in any way,

and

F. When the appliance exhibits a distinct change in perfor-

mance – this indicates a need for service.

Important Safeguards

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“ ” ’dangerous voltage within the product s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE S YST EM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

S2898A

1. Recording Copyright

Recording of copyrighted material for other than personal use is

illegal without permission of the copyright holder.

2. AC Fuse

The fuse is located inside the chassis and is not user-serviceable. If power

does not come on, contact your Onkyo authorized service station.

3. Care

From time to time you should wipe the front and rear panels and the

cabinet with a soft cloth. For heavier dirt, dampen a soft cloth in a

weak solution of mild detergent and water, wring it out dry, and

wipe off the dirt. Following this, dry immediately with a clean

cloth. Do not use rough material, thinners, alcohol or other chemi-

cal solvents or cloths since these could damage the finish or remove

the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME,

READ THE FOLLOWING SECTION CAREFULLY.

The voltage of the available power supply differs according to

country or region. Be sure that the power supply voltage of the area

where this unit will be used meets the required voltage (e.g., AC

230 V, 50 Hz or AC 120 V, 60 Hz) written on the rear panel.

Worldwide models are equipped with a voltage selector to conform

to local power supplies. Be sure to set this switch to match the volt-

age of the power supply in your area before plugging in the unit.

For British models

Replacement and mounting of an AC plug on the power supply cord

of this unit should be performed only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the

following code:

Blue : Neutral

Brown : Live

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the termi-

nals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal

which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the termi-

nal which is marked with the letter L or coloured red.

IMPORTANT

A 5 ampere fuse is fitted in this plug. Should the fuse need to be

replaced, please ensure that the replacement fuse has a rating of 5

amperes and that it is approved by ASTA or BSI to BS1362. Check

for the ASTA mark or the BSI mark on the body of the fuse.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE

SOCKET OUTLET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND DIS-

POSED OF SAFELY. THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED

INTO ANY 13 AMPERE SOCKET.

If in any doubt, consult a qualified electrician.

Precautions

For U.S. models

Note to CATV system installer:

This reminder is provided to call the CATV system installer s at-’

tention to Section 820-40 of the NEC which provides guidelines for

proper grounding and, in particular, specifies that the cable ground

shall be connected to the grounding system of the building, as close

to the point of cable entry as practical.

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the

party responsible for compliance could void the user s authority to’

operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for

help.

For Canadian models

NOTE: THIS CLASS B DIGITAL APPARATUS COMPLIES

WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUM RIQUE DE LAÉ

CLASSE B EST CON-FORME LA NORME NMB-003 DUÀ

CANADA.

Sur les mod les dont la fiche est polarisè ée:

ATTENTION: POUR VITER LES CHOCS É ÉLECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE

DANS LA BORNE CORRESPONDANTE DE LA PRISE ET

POUSSER JUSQU AU FOND.’

21. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or other hazards.

22. Safety Check – Upon completion of any service or repairs to the

appliance, ask the service technician to perform safety checks to

determine that the appliance is in proper operation condition.

23. Wall or Ceiling Mounting – The appliance should be mounted

to a wall or ceiling only as recommended by the manufacturer.

24. Heat – The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other appli-

ances (including amplifiers) that produce heat.

25. Liquid Hazards – The appliance shall not be exposed to drip-

ping or splashing and no objects filled with liquids, such as

vases shall be placed on the appliance.

FIGURE 1:

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL

ELECTRICAL CODE, ANSI/NFPA 70

Produktspecifikationer

Varumärke:	Onkyo
Kategori:	mottagare
Modell:	TX-SR600

Behöver du hjälp?

Om du behöver hjälp med Onkyo TX-SR600 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

mottagare Onkyo Manualer

Onkyo TX-RZ830 Bruksanvisning

24 Oktober 2024

Onkyo TX-910 Bruksanvisning

3 Oktober 2024

Onkyo R-805X Bruksanvisning

30 Augusti 2024

Onkyo TX-RZ920 Bruksanvisning

25 Augusti 2024

Onkyo TX-SR705 Bruksanvisning

24 Augusti 2024

Onkyo TX-SR600 Bruksanvisning

17 Augusti 2024

Onkyo HT-S5405 Bruksanvisning

17 Augusti 2024

Onkyo TX-SV444 Bruksanvisning

15 Augusti 2024

Onkyo HT-R2295 Bruksanvisning

15 Augusti 2024

Onkyo TX-8140 Bruksanvisning

14 Augusti 2024

mottagare Manualer

Nyaste mottagare Manualer

Speco Technologies PBM120AT Bruksanvisning

27 Oktober 2024

Fosi Audio V3 Bruksanvisning

26 Oktober 2024

Jensen CAR710-4BC Bruksanvisning

26 Oktober 2024

Pioneer VSX-1122K Bruksanvisning

22 Oktober 2024

NAD C 355BEE Bruksanvisning

21 Oktober 2024

Yamaha HTR-5072 Bruksanvisning

21 Oktober 2024

Yamaha RX-A810 Bruksanvisning

20 Oktober 2024

Sherwood R-607 Bruksanvisning

20 Oktober 2024

Denon AVC-S660H Bruksanvisning

19 Oktober 2024

Marantz Model 2330-B Bruksanvisning

19 Oktober 2024