OSD Audio XMP100 Bruksanvisning

OSD Audio mottagare XMP100

Läs nedan 📖 manual på svenska för OSD Audio XMP100 (4 sidor) i kategorin mottagare. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

OWNER’S MANUAL

XMP100

OsdAudio ®

775 Columbia St.,

Brea. CA92821

www.osdaudio.com XMP100 Owner’s Manual 51115

Congratulations on your purchase of the OsdAudio XMP100. ®

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dea diler or OsdAudio ® rectly at 888 779 4968.

Please read your ranty and retain your receipt and nal cartonwar origi

for possible future use.

For more information about OsdAudio ® electronics, speakers and

accessories please visit www.osdaudio.com

XMP100

Digital Stereo Power Amplifier

FEATURES:

• MAIN / INTERRUPT priority input switching

• Class D Amplification (89% Efficient)

• MAIN auxiliary output

• Speaker A/B switching

• Front panel Balance and Volume controls

• Signal sensing “Power On” and Trigger mode

SPECIFICATIONS

Stereo (8 ohm): 50W per nel, <1% THD+Nchan

Stereo (4 ohm): 75W per nel, <1% THD+Nchan

Bridged Mono (8 ohm): 160W, 1kHz, <1% THD+N

Frequency Response: 10Hz ~ 30kHz, -2dB/ +1dB

Signal to Noise Ratio: 100dB below 50W output into 8 ohms

w/20kHz Lowpass filter

Channel Separation: 65dB @ 1kHz, referred to 50W output

into 8 ohms

Input Sensitivity: 700mV input for rated 50W output

into 8 ohms

AC Power Consumption: 200W maximum

Net Weight: 4.7lbs / 2.2kgs

Gross Weight: 6.8lbs / 3kgs

2.15”

(55mm)

16.9” (430mm)

7.65”

(194mm)

• Rear mounted treble and bass controls

Bass/Treble Control: +/- 12dB @ 100Hz and 10kHz

DI GI TAL P OW ER

A M P L I F I E R

XMP100

D I GI TA L P O W E R

A M I E RP L I F

XMP100

OWNER’S MANUAL

APPLICA TIONS

STEREO SETUP

In this ration, the conﬁgu mode switch is set to “Stereo”. nnect the ne oCo li ut jacks

from a stereo pre-ampliﬁer or source to the MAIN input jacks of your XMP100.

Next c ne yo r speakers to the t als marked “Speaker A” observinon ct uermin g

prop pola paner ri Sele the “A” speakers sin the front ty. ct u g el zone selection

b ttons. nect a second (opt l) ir of speakers to the te als marked uCon iona pa rmin

“S aker B” f yo are c ectin 4 s akers to the M they m st be pe . I uonn gpe X P 010 u

8 ohm speakers only. Press A and B together to use both zones.

SETUP FOR MU L TIPLE SOURCE

In the m lt le s rce set p, a dist b ted io system is co ected to the uip ou u ri u aud nn

as a local zone li er via the MAIN p ts. lly the dist bamp ﬁin uNorma ri uted

aud audio system will be the io so rce for the . The disturib ted u audio is

then passed on to be sed by dit al zones or s b zones in the dist b ted uad ion uri u

system via the MAIN outputs.

Note: Main Out only duplicates what source is connected to the Main Input, ideal

for adding additional Amplifier or connect to Power Subwoofer.

The io o tp t of a local so rce, s ch as an M 3 layer, CD, television, aud u u u u P P

comp ter, etc., is cuonnected to the XM via the INTERRU TIN G pP 010 P in uts, and

whenever the local so rce is acutive i s al ll take rity over the ts ign wi prio

dist b ted a dio al ent at MAIN pri u u sign pres in ut . However, the distributed io saud ignal

will still be sent at the MAIN p t. In this mst ce the io o tp t of the pre in u circu an aud u u

local source will be rd via the M . Once the local s rce is t ed hea X P 010 ou urn

off or m ted, the Mu X P 010 ll awi utomatically switch back to the distributed dio au

system as an audio s rce, ass n the local s rce ns active. T re ou umi g ou remai in he

is a ay of p to 6 seconds del u when switching from INTERRUPTING input back

(From Pre-amp or Receiver Line Out)

(From Pre-amp Line Out)

(From Local Source Line Out) (Out to Additional Zones)

Limited Warranty

OsdAudio ® warrants its ampliﬁer p r oducts against defects in materials

and workmanship for a limited period of time. For a period of two years f r om

date of original pu r chase, we will r epair or r eplace the p r oduct, at our option,

without cha r ge for parts and labo r . Customer must pay all parts and labor

cha r ges after the limited warranty period expi r es. The limited warranty period

for factory r efurbished p r oducts expi r es after ninety (90) days f r om date of

original pu r chase.

This limited warranty applies only to pu r chases f r om authorized OsdAudio ®

elect r onics r etailers. This limited warranty is extended only to the original

pu r chaser and is valid only to consumers in the United States.

Consumers a r e r equi r ed to p r ovide a copy of the original sales invoice f r om

an authorized OsdAudio ® dealer when making a claim against this limited

warrant y . This limited warranty only covers failu r es due to defects in materials

or workmanship that occur during normal use. It does not cover failu r es

r esulting f r om accident, misuse, abuse, neglect, mishandling, misapplication,

alteration, faulty installation, modiﬁcation, service by anyone other than

AudioSou r ce®, or damage that is attributable to Acts of God. It does not

cover costs of transportation to OsdAudio ® or damage in transit. The

customer should r etu r n his defective p r oduct, f r eight p r epaid and insu r ed, to

OsdAudio ® only after r eceiving a Retu r n Authorization.

This warranty will become void if the serial number identiﬁcation has been

wholly or partially r emoved, alte r ed or erased. Repair or r eplacement under

the terms of this warranty does not extend the terms of this warrant y . Should

a p r oduct p r ove to be defective in workmanship or material, the consumer ’ s

sole r emedies will be r epair or r eplacement as p r ovided under the terms

of this warrant y . Under no ci r cumstances shall OsdAudio ® be liable for

loss or damage, di r ect, consequential or incidental, arising out of the use of

or inability to use the p r oduct. The r e a r e no exp r ess warranties other than

described above.

to MAIN inputs.

775 Columbia St.,Brea. CA92821

MX P 010

x x x x x x x

1 2 0 V ~ 6 0 H z / 2 0 0 W

XMP100

OWNER’S MANUAL

1. Power Switch

Switches the XMP100 on or o f f. A red LED indicates connection to AC power

while in standby mode. Turns green indicating audio signal is present.

2. Speaker Selector

Selects speaker zone A or B. For A + B zones push both buttons in.

3. Balance

Fades speaker output between the Right and Left Channels

4. V olume

Adjusts ampliﬁer volume.

FRONT P ANEL CONTROLS

6. Interupting Line Input

This is the sec ry uonda inp t, use MAIN IN for y r ou mai inpn u t.

INTE URR PT G IN INPUT can be used if a second source is desired and

takes r ove whe ignan s l is present and has at least a 5mV level.

W n t e is no l, or a s l with leshe her signa igna s than 5mV level, the amp

switc s back to MAIN IN after a he bri delef ay.

Main Input/Output

10.

11.

Mode Select Switch

Switches the ampliﬁer from Stereo mode to Bridged mode.

12.

13.

AUTO ON Select Switch

Power can be turned on and o manually ia the switch on the front panel ff v

or aut at y by om icall signa sel ns gin . Set it to NORMAL for manual power on/off.

Se to AU for s l s g the p l t n on n o s l is t TO igna sen in ; am wil ur whe audi igna

detected at the inputs. NOTE: The front panel power switch must be in the

ON position (pushed in) for the AUTO ON featu

r re to operate.

Speaker Zone A Output

Speaker output terminals for zone A. Minimum impedance: 8 ohm bridged

or 4 ohm stereo.

Speaker Zone B Output

Speaker output terminals for zone B. Minimum impedance: 8 ohm bridged

or 4 ohm stereo.

Power Cord

This i er is coampl ﬁn d for at n at 5V rth A ica) fuse ﬁgure oper io 11 (No mer . A

located int y otect n f m f lt it n Refer to if d ernall pr io ro au cond io s. qual ie

ser ice rs l s d this d to be aced vpe one houl nee repl .

REAR PANEL CONTROLS

Figu r e 1. F r ont Panel

Left Right

Balance Volume

SPEAKERS

A B

3 2 1

Min Max

POWER

5 8 10

Figu r e 2. Rear Panel

Connect

Receiver

Here

MAIN IN s d be used a the ry” or n u for the a i er. houl s “prima mai inp t mpl ﬁ

Conne ouct y r r or n s ce to t s u Use MAIN OUreceive mai our hi inp t. T to ss pa

MAIN IN signal to another amplifier.

If you will be connecting one or two pair of speakers to the ampliﬁer, place

the switch in the “St ” sit n. N For g 2 s of rs ereo po io OTE: playin pair speake

(A plus B), make sure each s aker has an nce of 8 pe impeda ohms or ater. gre

W n sehe t to “Bridged mod” e, the ampliﬁer is a e singl channel mono amplifier.

NOTE: The XMP100 s 0W in supplie 16 bridge modd e, P e leas verify that you r

speakers e car apable of handling such power to av d possoi ible damage!

For st o outpuere t c econn t the spe erak ’s positive (red) terminal to the iampl ﬁer’s

pos (red ermina an speaker’ neg (bla minaiti e v) t l, d the s ati e vck) ter l to the

ampliﬁer’s negative (black) terminal for each Right and Left speaker.

N E:OT To pre envt s ic at n in yon degrad io our speaker install ioat n, total s aker pe

wire resistance s d be kept w 0.5 mshoul belo oh . This table li recsts ommended

speaker wire gauge versus wire run length.

80’ or Less – 16 Gauge 2-Cond. CL3/FT4 Rated

80’ to 150’ – 14 Gauge 2-Cond. CL3/FT4 Rated

150 or more – 12 Gauge 2-Cond. CL3/FT4 rated

Place the “MODE” switch in the “BRIDGED” posit n d use both red io an

t l to c e to the s aker. e the s ak ’s positi e ed) ermina s onn ct pe Conn ct pe er v(r

t l to the s d (+) t l noted xermina ampliﬁer’ re ermina ne t to the bridging mark, d an

the s ak ’s ati e ack) t l tope er neg v(bl ermina the i ’s ampl ﬁer unmarked positi e v

N E:OT Only e z e (A or B) can be d. Do not att pon on bridge em t to bridge both

A and B speaker terminals! This may result in a lower impedance than the

ampl igne an damag ou ampl mii er is desﬁd for d may e y r i er The ﬁ. nimum

impedance for the total load connected in bridged mode is 8 ohms.

STEREO MODE

BRIDGED MODE

BRIDGED MODE- MONO APPLICATION

For d e, g ht d Le t et r as o outpu g bridge mod playin Rig an ft og he mon t, plu

RCA c s in to ht d Leable Rig an ft RCA at MAIN ut. inp

Set the MODE switch to BRIDGED d f w the st ctions an ollo in ru

for d s r c ct n in the ER ERMINALS sect n of bridge peake onne io SPEAK T io

this manual.

SPEAKER TERMINALS - STEREO MODE

SPEAKER TERMINALS - BRIDGED MODE

5. Bass and Treble Controls

These controls can adjust bass and treble frequencies +/- 12dB at 100Hz

and 10kHz.

8. 12V Trigger

A w the MP to be d on by ot r ect i or to erllo s X 100 powere he el ron cs pow

on othe ele ronir ct cs via a 3.5mm i e g c e. min phon plu abl

(red ermina) t l.

NOTE: Use Class 2 wiring for speaker connections.

To wire the output connector: 1. Strip the insulation off each speaker wire to

expose 3/8" (10 mm) of bare conductor. 2. Unscrew the output terminal binding

post several twists, insert each wire into the correct terminal. 3. Tighten binding

post by twisting clock-wise until it is firmly clamping the speaker wire.

Warning: While the amplifier does self-protect under most improper output

conditions, misconfiguration of loudspeaker mode and incorrect connection of

loudspeakers could damage connected loudspeakers and/or amplifier.

Please refer installation to a qualified installation professional, and always

check state and local electrical codes when installing.

CLASS 2

WIRING

775 Columbia St.,Brea. CA92821

D I TA L P OW E RG I

A M RP L I F I E

XMP100

Produktspecifikationer

Varumärke:	OSD Audio
Kategori:	mottagare
Modell:	XMP100
Typ av operation:	Buttons, Rotary
Power grill:	2150 W
Färg på produkten:	Grafiet
Inbyggd display:	Ja
Bredd:	900 mm
Djup:	600 mm
Höjd:	920 mm
Grill:	Ja
Energie-efficiëntieklasse:	A
Avfrostningsfunktion:	Ja
Höjd (min):	860 mm
Antal brännare/kokzoner:	6 zone(s)
Typ av häll:	Gaskookplaat
Elektronisk tändning:	Ja
Ugnens strömkälla:	Electrisch
Antal ugnar:	1
Antal gasbrännare:	6 zone(s)
Antal elektroniska kokzoner:	0 zone(s)
Avtagbar ugnslucka:	Ja
Ugnsstorlek:	Groot
Ugn med nettokapacitet:	97 l
Över- och undervärme:	Ja
Ugnens termostatområde:	50 - 250 °C
Bakplåtsmått:	Ja
Undervärmning:	Ja
Undervärmeeffekt:	1350 W
Övervärme:	Ja
Toppvärmeeffekt:	1200 W
Ugnsläge:	Bodem
Ugnskraft:	2750 W
Wokbrännare:	Nee
Ugnsdörr:	Deur naar beneden klappen
Typ produkt:	Range-fornuis
Enkel rengöring (ugn):	Ja