Ozito PXMBC-800 Bruksanvisning

Ozito Inte kategoriserad PXMBC-800

Läs nedan 📖 manual på svenska för Ozito PXMBC-800 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with

household waste but in an environmentally friendly way. Please recycle

where facilities exist. Check with your local council authority for

recycling advice.

Recycling packaging reduces the need for landll and raw materials.

Reuse of recycled material decreases pollution in the environment.

Please recycle packaging where facilities exist. Check with your local

council authority for recycling advice.

DESCRIPTION OF SYMBOLS

Warning

Do not store or use battery in

temperatures exceeding 50 C°

Volts Hertz

Alternating Current

Direct Current

Milliamperes

Watts

Amp Hour

HzV

ac/~

Lithium Ion Battery

Do not put in the rubbish

Do not get battery wet

Recycle Battery

Do not incinerate

Regulatory Compliance

Mark (RCM)

Do not store battery when the charge

is low; store between 40-60%.

40-60%

4.0Ah BATTERY

INSTRUCTION MANUAL

PXBP-400

SPECIFICATIONS

Input: 18V

Battery Capacity: 4.0Ah Li-ion

Power Consumption: 72Wh

Weight: 0.65kg

1. Battery

2. Battery Release Button

3. Charge Indicator Button

ozito.com.au

Before using the charger or battery read all instructions and cautionary markings on the charger, battery pack and the

product using the battery pack. Do not lose these safety instructions.

Battery Warnings

1. The battery pack is not fully charged out of the carton. First read the safety instructions and then follow the charging

notes and procedures.

2. For optimum battery performance avoid low discharge cycles. Charge the battery pack frequently.

3. Use and store the battery pack in dry conditions with low humidity between 0-50°C, ideally at 15°C. Avoid exposing

battery pack and charger to direct sunlight.

4. Do not keep battery pack in places where temperatures are liable to reach over 50°C, such as in a car, metal shed or

similar that is in direct sunlight.

5. Do not ignite the battery pack or expose it to re. There is a risk of explosion!

6. Do not exhaustively discharge batteries. Exhaustive discharge will damage the battery cells. The most common

cause of exhaustive discharge is long-term storage and continued use of low-charge batteries. Always store the

battery with some charge. Charge the batteries every 2-3 months to restore charge. Stop working as soon as the

performance of the battery falls noticeably or the electronic protection system triggers.

7. Protect batteries and the tool from overloads. Overloads will quickly result in overheating and cell damage inside

the battery housing without this overheating being apparent externally.

8. Avoid damage and shocks. Do not use batteries which have been dropped from a height of more than one meter or

strong external impact, even if the housing of the battery pack appears to be undamaged. The battery cells inside

the battery may have suffered serious damage. 

9. If the battery pack suffers overloading and overheating, the integrated protective cut-off will switch off the equip-

ment. Do not press the ON/OFF switch on the tool if the protective cut-off has actuated. This may damage the

battery pack. Allow the battery to cool to room temperature before use.

10. Use only original battery packs. The use of other batteries may result in injuries, explosion and a re risk.

11. Protect your rechargeable battery against moisture, rain and high humidity. Moisture, rain and high humidity can

cause dangerous cell damage. Never charge or use batteries which have been exposed to moisture, rain or high

humidity.

12. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack is damaged, do not

use the battery.

13. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or

other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals

together may cause burns or a re.

14. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If accidental contact occurs, ush

with water and seek medical help immediately. Liquid ejected from the battery may cause irritation or burns.

15. Do not use a battery pack or tool that is damaged or modied. Damaged or modied batteries may exhibit unpredict-

able behaviour resulting in re, explosion or risk of injury.

16. Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or temperature above 130°C

may cause explosion.

17. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer.

18. 18. Do not disassemble Battery. This may result in a risk of electric shock, electrocution or re.

Charger Warnings

19. Please check the data marked on the rating plate of the battery charger. Ensure to only connect the battery charger

to a power supply with the voltage marked on the rating plate.

20. Protect the battery charger and its cable from damage and sharp edges. Have damaged cables repaired by an

authorised service agent before use.

21. Keep the battery charger, batteries and the cordless tool out of children’s reach.

22. Do not use damaged battery chargers.

23. Do not use the supplied battery charger to charge other cordless tools. Only charge Ozito Power X Change

rechargeable batteries with an Ozito Power X Change Charger.

24. The battery pack may become warm during use. Allow the battery pack to cool to room temperature before

commencing with the charging.

25. Do not over-charge batteries. Do not exceed the maximum charging times. These charging times only apply to

discharged batteries. Frequent insertion of a charged or partly charged battery pack will result in over-charging and

cell damage. Do not leave fully charged batteries in the charger.

26. Charge the battery pack in dry conditions with low humidity between 10-40°C. Avoid exposing battery pack and

charger to direct sunlight.

27. Do not use batteries which have suffered deformation during the charging process or shows any other signs of

abnormalities including, excessive curvature of the housing, gassing, hissing or cracking.

28. Never fully discharge the battery pack. A complete discharge of the battery pack will lead to premature ageing of

the battery cells.

29. Never charge the batteries unsupervised.

30. Do not cover or place any object on top of the charger, place the charger away from heat sources.

31. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the

charger.

32. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or

stress.

33. An extension cord should not be used unless necessary. Use of an improper extension cord could result in the risk of

re, electric shock or electrocution.

34. Do not disassemble charger. This may result in a risk of electric shock, electrocution or re.

35. To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning. Removing the

battery pack will not reduce this risk.

36. Do not use the cordless tool or the battery charger near vapours and inammable liquids.

BATTERY & CHARGER SAFETY WARNINGS

ELECTRICAL SAFETY

When using mains-powered tools, basic safety precautions, including the following, should WARNING!

always be followed to reduce risk of re, electric shock, personal injury and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before

operating the tool. Save these instructions and other documents supplied with this tool for future reference.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in

order to avoid hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation

system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for

signs of damage, wear and ageing. Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the

power input of the tool or which is damaged or defective may result in a risk of re and electric shock.

To reduce the risk of electric shock, we recommend the use of a residual current device (rated 30mA or less).

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

BATTERY CHARGE INDICATOR

The purchased battery is equipped with a

battery charge indicator to show the state of

the battery charge.

Press the charge indicator button and look to

see which LED lights.

Battery requires immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note: The battery needs to be removed from the tool to check the state of charge.

BATTERY PROTECTION SYSTEM

The tool is equipped with a battery protection system, which helps to ensure longevity

of the battery.

The output power automatically cuts off during operation when the tool and/or battery

are placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull

the switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or

immediately after using the tool.

WARRANTY

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU

MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS

WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE

OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL

NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER

SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND

ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE

WARRANTY POLICY OR PROCEDURE.

The benets provided under this warranty are in addition to other rights and

remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are

entitled to a replacement or refund for a major failure and for compensation

for any other reasonably foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail to be of acceptable

quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under

this warranty, however, where you have suffered any additional direct loss as

a result of a defective product you may be able to claim such expenses by

contacting our customer service helpline above.

36 MONTH REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the original date

of purchase and is intended for DIY (Do It Yourself) use only. If a product is

defective it will be replaced in accordance with the terms of this warranty.

Warranty excludes consumable parts.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that specied

on the tool.

• If the tool shows signs of damage or defects caused by or resulting from

abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.

OZITO Australia/New Zealand (Head Ofce)

25 Fox Drive, Dandenong South, Victoria, Australia 3175.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

PXBP-400

1. OPERATION

CHARGING YOUR LITHIUM ION BATTERY

This battery has been shipped in a low charge condition, and requires charging prior to

use. Allow several cycles of charging and discharging (through use with a compatible

tool) for the battery to reach its optimum performance / runtime.

This battery is compatible with chargers from the 18V Ozito Power X Change range

available through your local Bunnings Warehouse. Product availability may differ.

Only use the battery pack with Ozito Power X Change 18V cordless products.

1. Insert the power plug of the charger into the mains socket outlet. The green LED

will begin to ash when properly connected to power supply.

2. Insert the battery pack into the battery charger .

3. Remove battery from the charger once fully charged. Disconnect the charger from

the power supply.

Note: The battery pack can become a little warm during the charging. This is normal.

If the battery pack fails to charge, check:

if there is voltage at the socket outlet

that the battery and charger are properly connected.

If the battery pack still fails to charge, please contact our customer service center.

0121

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with household

waste but in an environmentally friendly way. Please recycle where facilities exist.

Check with your local council authority for recycling advice.

Recycling packaging reduces the need for landll and raw materials. Reuse of

recycled material decreases pollution in the environment. Please recycle packaging

where facilities exist. Check with your local council authority for recycling advice.

DESCRIPTION OF SYMBOLS

1. Charging Unit LEDs

2. Charging Unit

ozito.com.au

MULTI BATTERY

FAST CHARGER

INSTRUCTION MANUAL

PXMBC-002

SPECIFICATIONS

Input: 220-240V ~AC 50-60Hz

Output 1: 18V DC, 3.0A

Output 2: 18V DC, 3.0A

Battery Charge Time: 30Min - PXBP-150 (18V 1.5Ah)

40Min - PXBP-200 (18V 2.0Ah)

50Min - PXBP-250 (18V 2.5Ah)

60Min - PXBP-300 (18V 3.0Ah)

75Min - PXBP-400 (18V 4.0Ah)

120Min - PXBP-520 (18V 5.2Ah)

100Min - PXUBP-520 (18V 5.2Ah Ultra)

Double Insulated

Volts Hertz

Amperes Amp Hour

Read Instruction Manual

Indoor Use Only Do not dispose of in rubbish

Regulatory Compliance

Mark (RCM)

Do not charge battery in

temperatures exceeding 40 C°

3.15A Slow Blow Fuse Warning

>40°C

V Hz

A Ah

T3.15A