PAC AP4-CH41 Bruksanvisning

PAC Inte kategoriserad AP4-CH41

Läs nedan 📖 manual på svenska för PAC AP4-CH41 (15 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/15
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev. V12
Date:092019
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH41 (R.2)
The AP4-CH41 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range, xed
level head unit output, in conjunction with CAN messages, the AP4-CH41 delivers a variable 5v RMS pre-amp output
with fading, balance, equalization, and level control capabilities. The module also retains all audio from other vehicle
features such as factory navigation prompts, Bluetooth, uConnect, and parking sensor chimes. A data controlled remote
amplier turn on wire is also provided by the AP4-CH41. When used in conjunction with the APA-TOS1 (sold separately),
the module can provide a variable, stereo, digital audio signal over ber optic (TOSLINK).
Introduction and Features
Important Notes
1. These instructions only apply to R.2.1.3.15 or later revisions of the AP4-CH41
2. Compatible with both amplied and non-amplied factory systems.
• Amplied Vehicles
• Compatible with all data-bus controlled amplied systems, no matter the screen size (including the 12" screen). To identify
these systems, look for logos on door speakers, tweeters, dash speakers or the subwoofer to conrm if the vehicle has an
amplied system (Alpine, Beats or Harman Kardon). Some vehicles may not always have branded systems. Unbranded
amplied systems are generally identied by locating a center channel speaker or subwoofer.
• Non-Amplied Vehicles
• Jeep Wrangler: Compatible with all screen sizes (5”, 7”, and 8”).
• All other models: Only compatible in vehicles equipped with the 7” or 8” screen. Vehicles equipped with the 5” screen
are not compatible.
• If you are installing the AmpPRO in a vehicle that is not equipped with a factory amplier, you must add an amplier to
the vehicle's speakers, as the factory radio will no longer have a 4 channel variable output after it has been re-congured
by the AmpPRO. For example, you can not add only a subwoofer to a non-amplied vehicle, as the radio will no longer
power the cabin speakers properly.
• Non-amplied vehicles equipped with an Active Noise Cancellation (ANC) system require the ANC module to be bypassed.
This can be done manually or with the ANC bypass harness ANC-CH01. The following vehicles have an ANC module
that needs to be bypassed:
• 2019 RAM Truck
• 2017-2019 Pacica
3. If a factory amplier is present, it must remain connected and in the vehicle after the Amp PRO has been installed.
4. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
5. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
6. The chime volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your particular
application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 2 for more details.
7. The level control knob must be connected in order to manually adjust the chime volume and minimum volume settings.
8. The factory radio's speed controlled volume and surround sound mode are not supported by the AP4 outputs.
9. When using the TOSLINK output (APA-TOS1 sold separately), DIP switch 1 must be on in order for all warning chimes to be
heard through the sound system (see page 2 for details).
10. No adjustments can be made manually using the programming button, or the factory SWC, when the module is connected to
a PC.
Module Layout
LED 1
TOSLINK Output
(APA-TOS1 sold separately)
Front Output
Ch. 1(L) and 2(R)
Rear Output
Ch. 3(L) and 4(R)
Non-Fading Output
Ch. 5(L) and 6(R)
LED 2
Interface Connector 1
Expansion Port
Programming Button
Feature Select
DIP switches
Non-Fading Level Control
Knob Connection
USB Connection
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev. V12
Date:092019
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH41 (R.2)
Installation
1. Remove factory radio.
2. Disconnect the main 52-pin factory harness from radio.
3. Connect AmpPRO harness to vehicle harness.
4. Connect AmpPRO harness to factory radio.
5. If you are using the AmpPRO in a vehicle with no factory amplier, connect the aftermarket amplier's speaker outputs to the
provided harness. If the vehicle has a factory amplifer, disconnect the harness with the loose speaker leads and connect it
to the matching plug on the AP4 harness.
6. Set any feature DIP switches that apply to your install.
a. Set DIP switch 1 on (down) to activate two channel mode. In this mode, both the TOSLINK and front RCA outputs (1 and
2) become non-fading outputs. All rear chimes will also be routed through these outputs in two channel mode.
b. Set DIP switch 2 on (down) to lower the RCA output voltage to 4v. Leave DIP switch 2 off (up) to keep the RCA output
voltage at 5v. See troubleshooting section on page 5 for more details.
c. DIP switch 3 is not used.
d. DIP switch 4 is for vehicles without a factory amplier. Set DIP switch 4 on (down) to recongure the radio for proper
communication with the AmpPRO. If you set this DIP switch on, once you connect the AmpPRO to the vehicle you
must do two full sleep cycles to recongure the radio. To do a sleep cycle, make sure the vehicle ignition is off,
close all doors, trunk and/or tailgate, lock the vehicle with the keyfob and let it sit for at least ve minutes. To
wake the vehicle back up, unlock the doors, turn on the ignition, and wait for the radio to come on. After two sleep
cycles the radio will be congured for a factory amplier and ready for use with the AP4. This can be veried by turning the
vehicle on, powering up the radio, and rolling the volume knob. If the radio is congured properly, LED 1 will ash rapidly
when the volume knob is turned.
7. If you are using the APA-TOS1 (sold separately) refer to the instructions included with that product for its installation.
8. Connect the AmpPRO harness to the module.
9. Connect the level control knob to the module and install in an accessible location.
10. Connect the signal cables and remote input from the aftermarket amplier.
DIP
1234
ON
Two Channel Mode 5v / 4v Preout No Function Non-Amplied Vehicles
1 2 3 4
Set DIP switches to the ON position to activate the corresponding features.
Set DIP switches to the OFF position for any features that are not desired.
Wiring Connection Chart
To Aftermarket
Amplier
Non-FadingRearFront
1(L) 2(R) 4(R) 5(L) 6(R)3(L)
Remote Turn On Output
2A Max Output
Factory Speaker
Connection Point
Factory Speaker
Connection Harness
To Radio To Vehicle
Harness
Non-Fading
Level Control
Knob
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 3
Rev. V12
Date:092019
Advanced Amplier Interface for
Chrysler / Dodge / Jeep / RAM
AP4-CH41 (R.2)
Setup and Conguration
1. Turn the ignition on. LED 1 on the interface will turn on and the +12v remote output will turn on.
2. Set the amp gain(s) to the desired level. We recommend using an oscilliscope and test tones to set the amp gain(s).
Please refer to the MECP Advanced study guide (p. 360) if you are unfamiliar with this process.
3. Check volume, balance, fade and EQ settings.
4. If you would like to adjust the chime volume or minimum volume, do so using one of the methods outlined on the next
page. If you are happy with the default levels, no adjustments are necessary.
Manually Setting the Chime Volume
You can manually set the level of the factory chime using either the programming button on the side of the interface or the
factory SWC. If you would like to set the chime volume using the AmpPRO PC app please proceed to the AmpPRO PC app
section.
PLEASE NOTE: Knob must be connected to module for either of the following methods.
Setting the chime volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Press the programming button on the side of the interface.
3. LED 1 will turn green and the chimes will begin continuously sounding.
4. Turn the level control knob clockwise until the desired chime level is reached.
5. You can now either press the programming button twice or wait ten seconds to exit the settings.
Setting the chime volume using the factory SWC
1. Start with the level control knob turned all the way down.
2. Press and hold the track down button on the factory SWC (Back left of steering wheel) for approximately ten seconds.
PLEASE NOTE: The radio will respond to the SWC commands during this process, this is normal and has no effect on the
AP4 operation.
3. LED 1 will turn green and the chimes will begin continuously sounding.
4. Turn the level control knob clockwise until the desired chime level is reached.
5. You can now either press the programming button twice or wait ten seconds to exit the settings.
Manually Setting the Minimum Volume
If the minimum volume of the radio (factory radio volume level 1) is too loud, you can manually set the level of the minimum
volume using either the programming button on the side of the interface or the factory SWC. If you would like to set the
minimum volume using the AmpPRO PC app, please proceed to the AmpPRO PC app section.
PLEASE NOTE: Level control knob must be connected to module for either of the following methods.
Setting the minimum volume using the programming button
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press the programming button on the side of the interface twice.
5. LED 1 will turn amber and the chimes will begin sounding every ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.
Setting the minimum volume using the factory SWC
1. Start with the level control knob turned all the way down (counter-clockwise).
2. Set the amp gains to the desired level.
3. Set the volume on the factory radio to 1.
4. Press and hold the track up button on the factory SWC (Back left of steering wheel) for approximately ten seconds.
PLEASE NOTE: The radio will respond to the SWC commands during this process, this is normal and has no effect on the
AP4 operation.
5. LED 1 will turn amber and the chimes will begin sounding every ve seconds.
6. Turn the level control knob clockwise until the desired minimum volume level is reached.
7. You can now either press the programming button once or wait ten seconds to exit the settings.

Produktspecifikationer

Varumärke: PAC
Kategori: Inte kategoriserad
Modell: AP4-CH41

Behöver du hjälp?

Om du behöver hjälp med PAC AP4-CH41 ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad PAC Manualer

PAC

PAC RP4-GM31 Bruksanvisning

26 September 2024
PAC

PAC NU-GM51 Bruksanvisning

26 September 2024
PAC

PAC NAV-1129 Bruksanvisning

26 September 2024
PAC

PAC LP7-2R Bruksanvisning

26 September 2024
PAC

PAC LP7-4 Bruksanvisning

26 September 2024
PAC

PAC GMK367B Bruksanvisning

26 September 2024
PAC

PAC CP1-FRD1 Bruksanvisning

26 September 2024
PAC

PAC C2A-CHY5 Bruksanvisning

26 September 2024
PAC

PAC NU-GM3 Bruksanvisning

26 September 2024
PAC

PAC CP1-TSL1 Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024