PAC C2A-CHY5 Bruksanvisning

Läs nedan 📖 manual på svenska för PAC C2A-CHY5 (1 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/1
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2A-CHY2 be held liable for consequential damages sustained
in connection with the C2A-CHY23. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to
assume obligation or liability in relation to the C2A-CHY23 other than its replacement.
3-06-14 866-931-8021• www.pac-audio.com
C2A-CHY/C2A-CHY23/C2A-CHY5
Add-an-Amp Interface
for Chrysler Dodge and Jeep Radios
5v RMS (max) pre-amp output with fading and balance capabilities. A radio controlled remote turn on
wire is also provided by the C2A-CHY.
Installation:
. In order for the C2A-CH to function Y
AOEM-CHR3 interface instead (excluding C2A-CHY5 Applications).
1. Remove the factory radio and connect the C2A harness between the original radio connector and the radio. If more that one
“T-harness” is installed make sure the C2A is connected to the radio and other “T-harnesses” are connected after the C2A.
2. The 18-pin black Molex attached to the C2A has 2 four (4) pin connectors attached to it. These must plug into each other.
Wht/Blk → Grn/Blk, Gry/Blk → Pur/Blk, White → Green, Grey → Purple
3. The 11-pin white output cable has the RCA connections and remote turn on wire. The remote turn wire is powered only when
the radio is on. YOU MUST USE THIS REMOTE TURN ON OUTPUT WITH THE NEW AMPLIFIER. FAILURE TO DO SO
MAY RESULT IN VERY HIGH VOLUME SPIKES WHEN THE RADIO IS FIRST TURNED ON. This is a R.A. (Retained not P
Accessory Power) wire. Connect the amplifiers RCA cables to the appropriate output (front - rear). Both front and rear outputs
do not need to be used in case of a 2 channel amplifier installation.
4. Connect the 18-pin Molex and 11-pin output connector to the C2A-CHY23 interface. The Black wire coming out of the 18-pin
connector will not be used in all installations. Test your amplifier for continuity from the RCA shield to the amplifier ground
connection terminal. If continuity exists, do not connect this black wire, isolate and do not use. If there is no continuity or if
there is high resistance between these two points, connect the black wire to the radio’s ground wire.
5. There are no adjustments on this interface, the radios fader and balance will control the C2A-CHY. Re-install the OEM radio. If
noise is present after installation it is recommended to use an SNI-1 noise filter.
AM/FM LIST
TUNE/SCROLL
SCAN SPEAK U.c. TIMESEEK RW
123456
AUX
SET
New Amplifier
Batt
Gnd
FL in
FR in
RL in
RR in
FL+
FR+
RL+
RR+
FL-
FR-
RL-
RR-
Rem
Not
Used
Factory Amplifier
+-
Connected
to new
speakers
Audio
Signal
Ground
Reference
Add an Amp Interface for Chrysler MSCANbus Radios with a Factory Amplifier
4 Channel RCA Output with a Radio Controlled 12v Remote Turn-on
www.pac-audio.com
Pacific Accessory Corporation Santa Ana, Ca 92705 ·
SAT
DISC
AUX
TYPE
SETUP
RNDEject
SEEK INFO FF
C2A-CHY
Remote Turn On Wire

Produktspecifikationer

Varumärke: PAC
Kategori: Inte kategoriserad
Modell: C2A-CHY5

Behöver du hjälp?

Om du behöver hjälp med PAC C2A-CHY5 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad PAC Manualer

PAC

PAC RP4-GM31 Bruksanvisning

26 September 2024
PAC

PAC NU-GM51 Bruksanvisning

26 September 2024
PAC

PAC NAV-1129 Bruksanvisning

26 September 2024
PAC

PAC LP7-2R Bruksanvisning

26 September 2024
PAC

PAC LP7-4 Bruksanvisning

26 September 2024
PAC

PAC GMK367B Bruksanvisning

26 September 2024
PAC

PAC CP1-FRD1 Bruksanvisning

26 September 2024
PAC

PAC C2A-CHY5 Bruksanvisning

26 September 2024
PAC

PAC NU-GM3 Bruksanvisning

26 September 2024
PAC

PAC CP1-TSL1 Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer