PAC RP5-GM32 Bruksanvisning

PAC Inte kategoriserad RP5-GM32

Läs nedan 📖 manual på svenska för PAC RP5-GM32 (5 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/5

RP5-GM32

Radio Replacement & Steering Wheel Control Interface

with OnStar Retention for General Motors Vehicles

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 091613

Introduction & Features

Important Notes

Wiring Connection Chart

Illustration / Schematic

The RP5-GM32 interface allows the replacement of a factory radio in select General Motors vehicles with 29-bit LAN

radios. Using this interface will retain factory features such as OnStar, steering wheel controls (SWC), warning chimes,

Rear Seat Controls (RSC) and the BOSE amplier when the original radio is removed. Use of this interface also allows

you to program two radio functions to each SWC button by using short press long press dual command functionality.

The RP5-GM32 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor

(VSS), illumination, reverse trigger and parking brake.

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the

interface into the vehicle (see next page for setting chart).

2. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions or utilize short press long press dual command functionality. The SWC can always be

restored to default settings by following the procedure outlined on page 3.

3. RSC buttons that are identical to the SWC will mimic the SWC one for one.

4. The LED will ash whenever a SWC button is pressed.

Aftermarket Radio Connectioons

Yellow Battery +12v

Black Ground

Red Accessory Output

White Front L + input

White / Black Front L - input

Grey Front R + input

Grey / Black Front R - input

Green Rear L + input

Green / Black Rear L - input

Purple Rear R + input

Purple / Black Rear R - input

SWC Connector

Blu/Yel Kenwwod, Newer

JVC

3.5mm Jack Alpine, JVC,

Clarion, Pioneer,

Sony, Fusion, Boyo,

Dual, Lightning

Audio, Visteon or

Advent

SWC Connection

See above chart for

different radio type

connections

Wiring SWC Connection

Page 1

Aftermarket

Radio

Connections

Vehicle

Connections

Red / White Parking Brake

Output (-)

Purple / White Vehicle Speed

Output

Blue / White Not Used

Blue Not Used

Orange / White Illumination Output

(+)

Green Reverse Output (+)

Brown Loop Mute Loop - See

installation note 7

RP5-GM32

Radio Replacement & Steering Wheel Control Interface

with OnStar Retention for General Motors Vehicles

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 091613

Installation Steps

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio

setting before plugging the interface into the vehicle.

2. Make all connections as described in the chart on page1.

3. Factory installed ampliers will determine the audio output connection. If the vehicle has a factory installed amplier use the factory

amplier audio location. If a factory installed amplier is not present use the non-amplied factory audio location.

4. If the vehicle is equipped with a Premium BOSE system, connect the subwoofer and center channel RCA inputs to the aftermarket radios.

If the aftermarket radio to be installed does not have a dedicated center channel or sub output do not use this cable. To ensure best sound

performance channel summing is not recommended. Use this cable according to the outputs that are available.

5. If the vehicle is equipped with a reverse camera and the aftermarket radio has a reverse camera input, connect the yellow RCA plug on the

gray connector to the aftermarket radios reverse camera input.

6. Plug the CMX chime module in if necessary (If the vehicle chimes when the radio is removed the CMX is not necessary). PLEASE NOTE:

In order to get the best possible sound out of the CMX please mount it in a place free and clear of any obstructions, preferably as close as

possible to the bottom of the dash pointing down toward the oor of the vehicle.

7. The Mute loop (if not cut) will turn the accessory output off when an OnStar or Bluetooth call is made or received. If the aftermarket radio

has a mute input cut this loop and connect the outer brown wire to the mute input.

8. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input).

9. If you wish to reassign functions to the SWC follow the programming instructions in the next section.

Optional Steering Wheel Control Programming

Page 2

Alpine Fusion Pioneer/Sony/OtherClarion JVC Kenwood

1 9 2 3 74

Other = Advent, BOYO, Dual, Lightning Audio, Visteon,

SET RADIO SELECT SWITCH

Alpine Fusion Pioneer/Sony/OtherClarion JVC Kenwood

1 9 2 3 74

Other = Advent, BOYO, Dual, Lightning Audio, Visteon,

SET RADIO SELECT SWITCH

IMPORTANT! The interface comes pre-programmed for the functions listed in the chart below and does not require programming

unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by

following the procedure outlined on page 3.

Alpine JVC Kenwood Clarion Sony/Pionee

Fusion

olume + Volume + Volume + Volume + Volume + Volume + Volume +

olume - Volume - Volume - Volume - Volume - Volume - Volume -

Source Source Source Source Source Source Source

Track + Track + Track + Track + Search + Track + Track +

Track - Track - Track - Track - Search - Track - Track -

oice Mute Mute Mute Mute Mute Mute

Play/Pause Preset + Preset/Disc - Disc/FM+ Band Preset +

udio

Default Steering Wheel Control Programming

Default SWC Button Assignments

If you wish to re-assign the SWC functions, utilize short press long press dual command functionality or select between Factory/

Aftermarket mode, the interface must be programmed in the specic order shown in the chart on page 3. If you come across a

function in the chart that your steering wheel does not have, or you do not want to program, press and release the program button

on the side of the interface to skip that function. The LED will ash off and on conrming that you have successfully skipped that

function and are ready to proceed to the next one.

RP5-GM32

Radio Replacement & Steering Wheel Control Interface

with OnStar Retention for General Motors Vehicles

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

www.pac-audio.com

Rev. 091613

Optional Steering Wheel Control Programming (cont.)

Radio Alpine JVC Kenwood Clarion Other* Sony Pioneer Fusion

1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +

2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -

3 Mute Mute Mute Mute Mute Mute Mute Mute

4 Preset + Source Source Source Preset + Preset + Preset + Source

5 Preset - Track + Play Search + Preset - Preset - Preset - Track +

6 Source Track - Track + Search - Source Source Source Track -

7 Track + Band/Disc + Track - Band Track + Track + Track + Audio

8 Track - Preset/Disc - Disc/FM + Send/End Track - Track - Track - Power

9 Power Select Disc/AM - Send Band Band Band

10 Enter/Play Attenuation Answer End

Reject Call/Source

(Bluetooth equipped

radios only)

Phone Menu

11 Band/Program Phone Receive Voice Dial Skip Answer Call

12 Receive Phone Reject On Hook Skip End Call

13 End Voice Dial Off Hook Skip Voice Activation

14 Power Mute (Multimedia

units only) Answer/End Call

*Other = Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & Visteon

Optional Programming Order

Page 3

The Mute button can be set to control the factory OnStar functions or given the ability to control the aftermarket radio. This option

can be set using the program button on the side of the interface. The default setting for this button is factory mode which controls

the factory OnStar. If this button is set to aftermarket mode, OnStar must be accessed by using the factory controls located on

the rearview mirror.

Aftermarket Mode

• OnStar control through the SWC Mute button is disabled.

This will free up the Mute button to send mute radio

command and another 2nd function.

Factory Mode

• The SWC Mute button is programmed to control OnStar

It cannot be programmed for short press/long press dual

command functionality and is blocked from doing so.

Use the function chart on the next page as a guide to program the functions in the proper order for your new radio

1. Turn the key to the ignition position.

2. Press and release the programming button on the side of the interface the number of times that corresponds with either

factory or aftermarket mode. One press will set factory mode and two presses will set aftermarket mode. The LED will blink

each time the button is pressed.

3. Once you have chosen either factory or aftermarket mode, after 2.5 seconds the LED will come on solid. At this point you

have two options:

A. To restore the SWC to factory default settings: Simply wait 7 seconds and the LED will blink 3 times indicating

the interface has timed out. The default settings are now restored and no further action is required.

B. To program custom SWC assignments: Proceed to step 4

4. With the LED on, press the rst button to be learned on the steering wheel, the LED will turn off. At this point you have

two options:

A. For short press functionality: Release the button within 1.5 seconds. The LED will turn back on.

B. For long press functionality: Hold the button until the LED starts blinking. Release the button and the LED

will go back to solid.

5. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.

6. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and

release the program button on the side of the interface to skip that function.

7. Once programming is completed, wait seven seconds. The LED will ash three times indicating end of programming.

8. Test the interface for proper functionality. Whenever a SWC is pressed the LED on the interface should blink. If any function

does not work, repeat the programming steps

Produktspecifikationer

Varumärke:	PAC
Kategori:	Inte kategoriserad
Modell:	RP5-GM32
Enhetsplacering:	Ingebouwd
Innehåll (inuti):	45 l
Typ av operation:	Touch
Magnetronkraft:	900 W
Färg på produkten:	Zwart
Antal effektnivåer:	5
Dörrgångjärn:	Neer
Skivspelare:	Nee
Inbyggd display:	Ja
Vikt:	34600 g
Bredd:	594 mm
Djup:	548 mm
Höjd:	455 mm
Nettoskatt:	3600 W
Uppvärmningsfunktion:	Ja
Grill:	Ja
Dörrfärg:	Zwart
Fördröjd starttimer:	Nee
Dörröppningsmekanism:	Omlaag trekken
Konvektionsmatlagning:	Ja
Ångkokning:	Nee
Håll varm funktion:	Ja
Rotisserie:	Nee
Avfrostningsfunktion:	Ja
Installationsfackets bredd:	568 mm
Installationsfack djup:	550 mm
Automatisk tillagningsfunktion:	Ja
Nuvarande:	16 A
Installationsfack höjd (min):	450 mm
Installationsfack höjd (max):	455 mm
Temperatur (max):	300 °C
Öppen dörr:	Deur naar beneden klappen
Maximal temperatur (konvektion):	300 °C
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50/60 Hz
Typ produkt:	Combinatiemagnetron
Type beeldscherm:	TFT
Lägsta temperatur (konvektion):	30 °C