PAC RPK5-GM4102 Bruksanvisning

PAC Inte kategoriserad RPK5-GM4102

Läs nedan 📖 manual på svenska för PAC RPK5-GM4102 (9 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/9

Page 1

PAC-audio.com

Email - support@pac-audio.com - Phone: 727-592-5991

Complete Radio Replacement Kit with Integrated Climate

Control Retention for 2010-2015 Chevrolet Camaro

RPK5-GM4102

Rev: R6

Date: 010419

Parts List

The RPK5-GM4102 includes everything you need for a professional installation of an aftermarket radio in your Camaro.

This kit contains:

1. Dash Kit

• (x1) PAC HVAC Control Panel (including factory style HVAC knobs)

• (x2) Radio Mounting Brackets (One left and one right)

• (x1) Pocket (For single DIN applications)

• (x8) Radio Mounting Screws

2. RP5-GM4101 (Camaro specic radio replacement module)

3. Camaro specic antenna adapter (BAA-DIN22).

4. Reverse camera retention harness for vehicles equipped with the MyLink system.

5. USB retention cable. This cable is compatible with vehicles equipped with the MyLink radios and vehicles equipped with the standard

non-touchscreen radios. It will require that the cable be ran to the back of the center console.

6. AUX retention cable for 2010-2012 vehicles equipped with the standard non-touchscreen radios and a USB port.

Overview

The RPK5-GM4102 is a complete radio replacement kit with integrated climate control retention for the 2010-2015 Chevrolet Camaro. This

kit comes equipped with factory style HVAC control knobs for a factory look and experience. To add to the factory look and experience, the

exterior temperature display is retained by a small OLED display at the top of the kit retaining this valuable vehicle feature. This kit also

includes all of the modules and cables needed to retain all of the important features of the factory system such as OnStar, factory warning

chimes, factory Bluetooth, steering wheel mounted radio controls, factory reverse camera, factory amplier (if equipped), factory AUX jack

(if equipped) and the factory USB port (if equipped). The RPK5-GM4102 also provides data bus driven outputs such as retained accessory

power (RAP), vehicle speed sensor (VSS), illumination, reverse trigger and parking brake. Use of this interface also allows you to program

two radio functions to each SWC button by using short press long press dual command functionality.

Important Notes

1. These instructions only apply to or later revisions of the RP5 interface. The revision info can be found on a small white sticker on the R.2.5.6.3

interface.

2. The center inserts on the control knobs are made to install once! They are not easily removable / swappable. Please ensure you have selected

the correct inserts for your installation before snapping the inserts into the control knobs.In the event that the center inserts need to be removed,

see the troubleshooting section on page 9.

3. For vehicles with heated seats: When installing the center caps, you need to rst install the light pipes. They are keyed so they will only t one

way. Pay close attention to the shape and orientation of the light pipes to ensure correct lighting.

4. When discussing the control knobs, we will refer to “Left” indicating the driver side, and “Right” indicating the passenger side.

5. It is recommended that the user’s phone(s) be “Unpaired” from the factory Bluetooth. This will ensure the user’s phone will always pair to the

aftermarket radio’s bluetooth.

6. Once the radio has been removed, the vehicle settings which are normally selected through the factory radio can be accessed using the

PAC-UP along with the PAC Vehicle Settings program (for windows PC), which can be downloaded here: http://www.pac-audio.com/

rmware.

7. The Answer/Voice and End/Mute buttons can be set to control the factory OnStar functions, or to control the aftermarket radio. This option can

be found in the PAC Vehicle Settings program mentioned above in note one. The default setting for these buttons is to control the factory OnStar.

If these buttons are set to control the aftermarket radio, OnStar can still be accessed by using the mirror controls.

8. The radio replacement interface comes pre-programmed for all of the vehicle’s factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions or utilize the short press long press dual command functionality. The SWC can always be restored to

default settings by pressing and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.

9. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the interface into the

vehicle (see page 4 for setting chart).

Page 2

PAC-audio.com

Email - support@pac-audio.com - Phone: 727-592-5991

Complete Radio Replacement Kit with Integrated Climate

Control Retention for 2010-2015 Chevrolet Camaro

RPK5-GM4102

Rev: R6

Date: 010419

1.3 1 - Remove the 4 x 7mm bolts ( ) securing the radio

( ) into the dash. Slide the radio ( ) to the rear and 2 2

disconnect all electrical connections.

You can now set the factory radio aside as it will not

be needed any longer.

Proceed to the next section to transfer the retention

clips from the factory radio control assembly to the

PAC HVAC control assembly.

Removing the factory radio from the vehicle

1.1 - Apply the parking brake. Move the transmission shift

assembly to the most rearward position possible. Use a at

bladed plastic trim tool to release the retainer tabs securing

the front oor console front cover to the console assembly.

Lift the cover ( ) up and towards the rear, making sure that 1

the accessory power receptacle and the electronic traction

control switch clears the transmission shift assembly. It may

be necessary to pop these items loose from the underside to

achieve clearance. Disconnect the harnesses.

1.2 - 1 Remove the 2 x 7mm bolts ( ) securing the radio

control assembly (2) into the dash. Then use a at-

bladed plastic trim tool to release the retainer clips

securing the radio control assembly ( ) to the instrument 2

panel. Disconnect the electrical connections.

Page 3

PAC-audio.com

Email - support@pac-audio.com - Phone: 727-592-5991

Complete Radio Replacement Kit with Integrated Climate

Control Retention for 2010-2015 Chevrolet Camaro

RPK5-GM4102

Rev: R6

Date: 010419

Dash Panel Assembly

2.1 - Using a at bladed pry tool, carefully remove two of the

retention clips off of the black plastic backing of the factory radio

control assembly.

2.2 - Slide the retention clips (removed during the previous

step) onto the two black posts at the top of the PAC HVAC

control assembly.

To secure the top of the PAC HVAC control assembly into the dash, remove two of the retention clips located on the back side at the top of the

factory radio control assembly, and reuse them on the PAC HVAC control assembly.

Knob Inserts

For vehicles without heated seats: Remove the center cap called “Blank Left” and snap that into the climate control knob labeled Left. The insert

is keyed, so it will only t in one orientation. Remove the center cap called “Blank Right” and snap it into the climate control knob labeled Right.

For vehicles equipped with heated seats: Carefully open the package labeled “Heated Seat Left”. There will be a center cap and 2 small, clear

plastic, light pipes. They are keyed, so they will only t in one specic hole each.

1. From the front of the control knob, insert the light pipes (non-keyed side rst) into the small rectangular openings.

2. The left light pipe (A) has a key tab on the narrow side. Insert this light pipe with the key facing down.

3. The right light pipe (B) has the key tab on the wide side. Insert this light pipe with the key facing to the right.

(A)

(B)

Close-up of light pipes installed

key tab

Produktspecifikationer

Varumärke:	PAC
Kategori:	Inte kategoriserad
Modell:	RPK5-GM4102
Vormfaktor:	Half-Height/Half-Length (HH/HL)
Maximal upplösning:	1600 x 1200 Pixels
Anslutningar:	KX20-DVI\nCable to 4x DVI-I
Mac-kompatibilitet:	Nee
Typ av anslutning:	PCI
Typ av kylning:	Passief
Grafikadapter, minnestyp:	GDDR
Minnesbuss:	64 Bit
DirectX version:	Nee