Panasonic EX11EBPN Bruksanvisning

Panasonic Inte kategoriserad EX11EBPN

Läs nedan 📖 manual på svenska för Panasonic EX11EBPN (1 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

INSTRUCTION MANUAL

EX-10 Series

Ultra-slim TypePhotoelectric Sensor

SPECIFICATIONS1

φ1mm opaque object

Setting distance between

emitter and receiver: 150mm

φ2mm opaque object

Setting distance between

emitter and receiver: 500mm

0.1mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2m long (Note 4)Cable

Red LED (lights up when the output is ON), located on the receiver for the thru-beam type sensorOperation indicator

Green LED (lights up under stable light received condition or stable dark condition),

located on the receiver for the thru-beam type sensor

Stability indicator

15% or less of

operation distance

−

Hysteresis

0.1mm or less0.05mm or less

Repeatability

(perpendicular to sensing axis)

2 to 25mm (Note 2)

(Conv. point: 10mm)

500mm

Enclosure: Polyethylene terephthalate, Lens: PolyalylateMaterial

Emitter, receiver: 20g approx. each 20g approx.Weight

Mounting screws: 2 sets

Mounting screws: 1 set

Accessories

Red LED (modulated)

0.5ms or lessResponse time

IP67 (IEC)Protection

-25 to +55 (Note 3) (No dew condensation or icing allowed), Storage: -30 to +70℃ ℃Ambient temperature

35 to 85% RH, Storage: 35 to 85% RHAmbient humidity

Emitting element

Incorporated

Output

Short-circuit protection

<EX- A(-R), EX- B(-R)>□ □

NPN open-collector transistor

・Maximum sink current: 50mA

・

Applied voltage: 30V DC or less (between output and 0V)

・Residual voltage: 1V or less (at 50mA sink current)

0.4V or less (at 16mA sink current)

<EX- A-PN, EX- B-PN>□ □

PNP open-collector transistor

・Maximum source current: 50mA

・

Applied voltage: 30V DC or less (between output and +V)

・Residual voltage: 1V or less (at 50mA source current)

0.4V or less (at 16mA source current)

Current consumption

12 to 24V DC 10% Ripple P-P 10% or less±

Emitter: 10mA or less, Receiver: 15mA or less 20mA or less

Supply voltage

150mmSensing range

φ0.1mm copper wire

(Setting distance: 10mm)

Min. sensing object

Front sensing Side sensing Front sensing Front sensing Front sensingSide sensing

EX-11A -PN -R( / )

EX-11EA -PN -R( / )

EX-13A -PN -R EX-19A -PN -R EX-14A -PN -R( / ) ( / ) ( / )

EX-13EA -PN -R( / )

EX-11B -PN -R( / )

EX-11EB -PN -R( / )

EX-13B -PN -R EX-19B -PN -R EX-14B -PN -R( / ) ( / ) ( / )

EX-13EB -PN -R( / )

Thru-beam

Convergent reflective

Type

Model No.

(Note 1)

Dark-ON

Light-ON

Item

φ2mm opaque object

Setting distance between

emitter and receiver: 1m

Notes: 1) Model Nos. having the suffix ' ' are PNP output type. -PN

Further, model Nos. having suffix ' ' are inflection resistant -R

cable type. (NPN output type only)

The model No. with suffix ' ' shown on the label affixed to the P

thru-beam type sensor is the emitter, ' ' shown on the label is D

the receiver.

Thru-beam type sensor emitter: , Thru-beam type sen-EX- P□

sor receiver: EX- D□

Notes: 2)

The sensing range of the convergent reflective type sensor is

specified for white non-glossy paper (50 50mm) as the ×

object.

-10 to +55 for the inflection resistant cable type.℃

The inflection resistant type has a 0.1mm

3-core (thru-beam

type emitter: 2-core) inflection resistant cabtyre cable, 2m long.

CAUTIONS3

●

This product has been developed / produced for industrial use only.

For the convergent reflective type , if there is a EX-14□

reflective object (e.g., a conveyor, etc.) in the background

of the sensing object, since it may affect the sensing, use

by keeping enough distance from the reflective object.

The thin cable (0.1mm2) is used for this product. Thus, take care that

if the cable is pulled with excessive force, it may cause cable break.

Make sure that the power supply is off while wiring.

Take care that wrong wiring will damage the sensor.

Verify that the supply voltage variation is within the rating.

If power is supplied from a commercial switching regula-

tor, ensure that the frame ground (F.G.) terminal of the

power supply is connected to an actual ground.

In case noise generating equipment (switching regulator, inverter

motor, etc.) is used in the vicinity of this product, connect the frame

ground (F.G.) terminal of the equipment to an actual ground.

Do not run the wires together with high-voltage lines or

power lines or put them in the same raceway. This can

cause malfunction due to induction.

Extension up to total 50m, is possible with 0.3mm2, or

more, cable for both, emitter and receiver. However, in or-

der to reduce noise, make the wiring as short as possible.

Do not use during the initial transient time (50ms) after

the power supply is switched on.

Take care that the sensor is not directly exposed to fluorescent

lamp from a rapid-starter lamp, a high frequency lighting device

or sunlight etc., as it may affect the sensing performance.

This sensor is suitable for indoor use only.

Avoid dust, dirt, and steam. Do not use it in places hav-

ing excessive vapor, dust, etc., or where it may come in

contact with corrosive gas.

Take care that the sensor does not come in contact with

water, oil, grease, organic solvents, such as, thinner

etc., or strong acid, and alkaline.

Make sure that stress by forcible bend or pulling is not

applied directly to the sensor cable joint.

Since the cable end is not waterproof, do not use the sensor in

the application where water may seep in from the cable end.

I/O CIRCUIT DIAGRAMS4

Symbols... D

Tr1

Tr2

: Reverse supply polarity protection diode

: Surge absorption zener diode

: NPN output transistor

: PNP output transistor

Sensor circuit

12 to 24V DC

±10%

D (Brown) +V

(Bla ck

) Out

pu t (Note)

(Blue

) 0V

ZD50mA max.

Tr1

Load

Color code

Internal circuit Users' circuit

●EX- A(-R), EX- B(-R) / NPN output type□ □

Note:

The emitter of the thru-beam type sensor does not incorporate the output.

Sensor circuit

12 to 24V DC

±10%

(Brown) +V

(Bla ck

) Out

pu t (Note)

(Blue

) 0V

ZD50mA max.

Tr2

Load

Color code

Internal circuit Users' circuit

●EX- A-PN, EX- B-PN / PNP output type□ □

Note:

The emitter of the thru-beam type sensor does not incorporate the output.

MOUNTING2

●In case of mounting on tapped holes (Unit: mm)

・The tightening torque should be 0.2N・m or less.

Side sensing Front sensing

Attached

screw

[M2 (length 10)]

M2 0.4 holes×

tapped 6 deep

Sensing

direction

Attached

screw

[M2 (length 8)]

M2 0.4 holes×

tapped 7 deep

Sensing

direction

Side sensing Front sensing

●

In case of using attached screws and nuts (Unit: mm)

・The tightening torque should be 0.2N・m or less.

11 Spring

washers

Flat washers

Nuts

Attached screw

[M2 (length 10)]

Thickness of mounting plate

2 or less

Thickness of mounting plate

2.5 or less

Attached screw

[M2 (length 8)]

Sensing

direction

Sensing

direction

OPTIONAL SENSOR MOUNTING BRACKET

●

When mounting the sensor with the optional sensor

mounting bracket, use the attached M2 screws and

the tightening torque should be 0.2N・m or less.

Six types of optional sensor mounting brackets are available.

MS-EX10-11

MS-EX10-3

MS-EX10-13

MS-EX10-12

MS-EX10-2

MS-EX10-1

Model No. Description

Mounting bracket for front sensing type only Two

M2 (length 4mm) pan head screws are attached.

Mounting bracket for side sensing type only Two

M2 (length 8mm) pan head screws are attached.

L-shaped mounting bracket

Two M2 (length 4mm) pan head screws, and two

M2 (length 8mm) pan head screws are attached.

Mounting bracket for front sensing type only

Two M2 (length 4mm) pan head

screws (stainless steel) are attached.

Mounting bracket for side sensing type only

Two M2 (length 8mm) pan head

screws (stainless steel) are attached.

L-shaped mounting bracket

Two M2 (length 4mm) pan head screws (stain-

less steel), and two M2 (length 8mm) pan

head screws (stainless steel) are attached.

Material

Stainless

steel

(SUS304)

Cold rolled

carbon steel

(SPCC)

OPTIONAL SLIT MASK

(EX-13 and EX-19 only)□ □

●

Apply a slit mask when detecting small objects or for in-

creasing the accuracy of sensing position. However, the

sensing range is reduced when the slit mask is mounted.

●

The slit mask should be mounted on the sensor be-

fore mounting the sensor.

If the front sensing type sensor is used along with the

slit mask and the optional sensor mounting bracket

for the front sensing type, or MS-EX10-1 MS-EX10-

11, as shown in the figure below, a 0.2mm, or more,

thick spacer is separately required.

Slit mask for front sensing type only

(hole diameter: 1.5mm)φ

Slit mask for side sensing type only

(hole diameter: 1.2mm)φ

OS-EX10-12

OS-EX10E-12

(Note)

OS-EX10-15

Slit mask for front sensing type only

(hole diameter: 1.2mm)φ

Stainless

steel

(SUS304)

Model No. Description Material

Note: Excluding .EX-19□

M3 screws

0.2mm, or more, thick spacer

is separately required.

Thank you very much for using SUNX products. Please

read this Instruction Manual carefully and thoroughly for the

correct and optimum use of this product. Kindly keep this

manual in a convenient place for quick reference.

WARNING

●

Never use this product as a sensing device for personnel protection.

In case of using sensing devices for personnel protection, use prod-

ucts which meet laws and standards, such as OSHA, ANSI or IEC

etc., for personnel protection applicable in each region or country.

INTENDED PRODUCTS FOR

CE MARKING

●

The models listed under ' ' SPECIFICATIONS

come with CE Marking.

As for all other models, please contact our office.

PRINTED IN JAPAN

Overseas Sales Dept. (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan

Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany

Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA

Phone: +1-908-464-3550

URL : sunx.jp

SUNX Limited

Produktspecifikationer

Varumärke:	Panasonic
Kategori:	Inte kategoriserad
Modell:	EX11EBPN
Färg på produkten:	Blauw
Vikt:	159 g
Bredd:	82 mm
Djup:	39 mm
Höjd:	114 mm
Internationell säkerhetskod (IP):	IPX5
Blåtand:	Ja
På / Av knapp:	Ja
Anslutningsteknik:	Bedraad en draadloos
Typ av strömkälla:	Batterij/Accu
Genomsnittlig effekt:	- W
Antal högtalare:	1
Volymkontroll:	Digitaal
Rekommenderad användning:	Tablet/smartphone
3,5 mm-kontakt:	Ja
Säkerhetsfunktioner:	Spatwaterdicht
USB-laddningsport:	Ja
Ljudutgångskanaler:	- kanalen
Antal förare:	1
AUX ingång:	Ja
Produktdesign:	Overige
Wifi:	Nee
Batteriteknik:	Lithium-Ion (Li-Ion)
Batterityp:	Ingebouwd