Panasonic FX-501 Bruksanvisning

Panasonic Inte kategoriserad FX-501

Läs nedan 📖 manual på svenska för Panasonic FX-501 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

INSTRUCTION MANUAL

Digital Fiber Sensor Amplier □FX-501

MJE-FX501 No.0015-31V

Thank you very much for purchasing Panasonic products.

Please read this Instruction Manual carefully and thoroughly for the correct and

optimum use of this product.

Kindly keep this manual in a convenient place for quick reference.

WARNING

●Never use this product as a sensing device for personnel protection.

●In case of using sensing devices for personnel protection, use products which

meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel

protection applicable in each region or country.

1INTENDED PRODUCTS FOR CE MARKING

●This product complies with the following standards / regulations.

EMC Directive 2004/108/EC

ANSI/UL 60947-5-2, CAN/CSA C22.2 No.14

S1-G-1-2009, S2-W-5-2009

●Caution about UL recognition

In case requiring conformity of UL listing mark or C-UL listing mark, USe class

2 power supply unit.

2PART DESCRIPTION

Pressing down SET key + MODE key for 3 sec : Set key lock or release key lock

3MOUNTING

How to connect

1. Fit the rear part of the mounting sec-

tion of the amplier on a DIN rail.

2. Press down the r ea r part of the

mounting section of the unit on the

DIN rail and fit the front part of the

mounting section to the DIN rail.

How to remove

Push the controller forward.

2. Lift up the front part of the amplier

to remove it.

How to connect the ber cable

Be sure to t the attachment to the bers rst before inserting the bers to the

amplier. For details, refer to the instruction manual enclosed with the bers.

1. Snap the fiber lock lever down till it

stops completely.

2. Insert the ber cables slowly into the

inlets until they stops. (Note)

3. Return the fiber lock lever to the

original position till it stops.

Note: With the coaxial reective type ber, such as , , insert the single core ber cable into the FD-G4 FD-FM2 or

beam-emitting inlet “P” and the multi-core ber cable into the beam-receiving inlet.

If they are inserted in reverse, the sensing performance will deteriorate.

Fiber lock lever

Fiber for

receiver

1. Snap

3. Return

2. Insert

Fiber for emitter

2. Lift up

1. Push forward

2. Press down

1. Fit

35mm width DIN rail

Digital display

(Green / Red)

MODE indicator: CUST (Yellow)

MODE indicator: PRO (Yellow)

MODE indicator: L / D (Yellow)

UP key

• Teaching

• Threshold value

ne adjustment

• Select setting items

SET key

• Teaching

• C o nf i rm s e tt i ng

contents

DOWN key

• Teaching

• Threshold value ne

adjustment

• Select setting items

Sensing output

operation indicator

(Orange)

MODE key

• Select Modes

• Cancel during setting

INSTALL MORE AMPLIFIER OF SERIES CONNECTION TYPE

●Make sure that the power supply is OFF while adding or removing the series

connection type.

●In case 2 or more the series connection types are connected in cascade, make

sure to mount them on a DIN rail.

● In case installing additional amplier of series connection type, the maximum

11 the series connection types using sub cables can be added to an amplier

using a main connection cable.

●When connecting 2 or more the series connection types in cascade, use the

sub cable (optional) for the second series connection type onwards.

For mounting and removing the amplier, refer to “ MOUNTING.”

How to cascade

1. Mount the ampliers, one by one,

on the DIN rail.

2. Slide the amplifiers next to each

other, and conne ct the quick-

connection cables.

3. Mount the end plates MS-DIN-E

(optional) at both the ends to hold

the amplifiers between their flat

sides.

Tighten the screws to fix the end

plates.

How to Remove

1. Loosen the screws of the e nd

plates.

2. Remove the end plates.

3. Slide the amplifiers and remove

them one by one.

5I/O CIRCUIT DIAGRAMS

<FX-501>

<FX-505P-C2>

Note: The quick-connection sub cable does not incorporate +V (brown) and 0V (blue). The power is supplied from

the connector of the main cable.

Terminal

No. Terminal name

1 +V

2 Sensing output

3 0V

6OPERATION PROCEDURE

The changed settings are not stored if turning the power OFF while

setting. Therefore, conrm the settings by pressing the SET key before

turning the power OFF.

●When turning ON the power, RUN mode is displayed and the digital display

shows the threshold value (green) and the incident light intensity (red).

12 to 24V DC

Main circuit

(Brown) +V (Note)

(Black) Sensing output

(Blue) 0V (Note)

Load

Main circuit

(Brown) +V (Note)

(Black) Sensing output

(Blue) 0V (Note) Load

12 to 24V DC

• Displays threshold value (green) and incident light intensity (red).

• Teaching, threshold value ne adjustment and key lock function

can be set.

• For setting method of each function, refer to “ TEACHING

MODE,” “ THRESHOLD VALUE FINE ADJUSTMENT FUNC-

TION,” or “ KEY LOCK FUNCTION.”

• Select either Light-ON or Dark-ON.

• For the setting, refer to

“SENSING OUTPUT OPERATION

MODE

.”

• The default setting is “ ” (Light-ON).

• An item set in CUSTOM mode (Response time setting, Emission

power setting and Hysteresis setting) is displayed.

• For details, refer to “ CUSTOM MODE.”

• The default setting is “ ” (response time setting).

• Advanced setting can be done.

• For the setting, refer to “ PRO MODE.”

Slide

Communication

window

Slide

Main cable

(Optional)

Sub cable

(Optional)

End plate

MS-DIN-E (Optional)

End plate

MS-DIN-E

(Optional)

1-point teaching (Window comparator mode / Hysteresis mode)

●This is method to set the shift amount to the desired value and to set the

threshold range by using the 1-point teaching.

Notes 1)

The shift amount of 10% is an initial value. The shift amount can be set in PRO mode. Furthermore, the shift

value can be set in incident light amount. For setting method, refer to “PRO MODE OPERATION MANUAL.”

2) If the value after setting exceeds the maximum (minimum), the maximum (minimum) sensitivity will be set.

2-point teaching (Window comparator mode / Hysteresis mode)

●This is method to set the threshold range by conducting the 2-point teaching (P-1, P-2).

●When conducting teaching, use sensing objects (P-1 and P-2) whose incident

light intensities are different from each other.

Note: If the value after setting exceeds the maximum (minimum), the maximum (minimum) sensitivity will be set.

3-point teaching (Window comparator mode / Hysteresis mode)

●This is the method to conduct the 3-point teaching (P-1, P-2, P-3) and to set the

threshold range by setting the threshold value (1_SL) of the mid-point between “A”

and “B” and the threshold value (2_SL) of the mid-point between “B” and “C”.

●When conducting teaching, use sensing objects (A, B and C) whose incident

light intensities are different.

●After teaching, P-1, P-2 and P-3 will be automatically relocated in ascending order:

i.e. the lowest value is placed in “A”, the second lowest in “B” and the highest in “C”.

Note: If the value after setting exceeds the maximum (minimum), the maximum (minimum) sensitivity will be set.

Span adjustment in rising differential mode or trailing differential mode

● Press the SET key to conrm the setting item.

● The threshold can be set by using the threshold value ne adjustment function.

For the threshold value ne adjustment function, refer to “ THRESHOLD

VALUE FINE ADJUSTMENT FUNCTION”

Stable sensing is possible

1. Pressing SET key down (1st time)

2. Press down the SET key in the sensing object present condition.

(2nd time)

Stable sensing is not possible

1_SL (P-1) 2_SL (P-2)

1_SL (P-1) 2_SL (P-2)

A 2_SL1_SL B C

A 2_SL1_SL B C

Stable sensing is possible

1. Press SET key down in the sensing object present condition (1st time)

Press SET key down in the sensing object present condition (2nd time)

Stable sensing is not possible

Press SET key down in the sensing object present condition (3rd time)

Short span

Long span

Changed intensity

1_SL P-1 2_SL

1_SL P-1 2_SL

Stable sensing is possible

1. Pressing SET key down

2. Press the SET key down in the sensing object present condition.

Stable sensing is not possible

3. The threshold value (1_SL) that is 10% lower from the incident

light intensity and the threshold value (2_SL) that is 10% higher

from the incident light intensity are set. (Note 1, 2)

Set to de-

sired value

Set to de-

sired value

Set to de-

sired value

Set to de-

sired value

7TEACHING MODE

●Be sure that detection may become unstable depending on the use environ-

ment in teaching if less margin is applied.

●When teaching in Window comparator mode or Hysteresis mode, a setting

has to be made in PRO mode beforehand.

In case 1-point teaching, make sure to set the shift amount. (initial value is

10% or 100)

For the setting, refer to “PRO MODE OPERATION MANUAL.”

●Teaching can be set in RUN mode.

Useful when sensing object can be set

●This is basic teaching method.

2-point teaching

Useful when sensing object cannot be set

●This is teaching method in case small object or object in back ground are existing

Limit-teaching

Note: The shift value of approx. 15% is an initial value. Display of the shift value can be changed to percentage

[approx. 0 to 999% (unit 1 %)] or incident light intensity [0 to 9999 (unit 1)].

For setting the shift amount, refer to “PRO MODE OPERATION MANUAL.”

Useful when not want to stop production line and to keep the sensing object move

Full-auto teaching

Stable sensing is possible

1. Pressing SET key down

Run the sensing object on the line and hold down the SET key.

Stable sensing is not possible

3. “ ” is displayed on the digital display (green) and when the

sensing object passed through, release the SET key.

Automatic

Pressing down long

<Thru-beam type and refractive type are common>

<Reective type>

1 2

<Thru-beam type>

Stable sensing is possible

1. Press the SET key in the sensing object present condition.

2. Press the SET key in the sensing object absent condition.

Stable sensing is not possible

<Thru-beam type and refractive type are common>

Stable sensing is possible

1. Press the SET key in the sensing

object present condition or non

sensing object present condition.

2. The threshold level is shifted to

high value (low sensi tiv ity) by

pressing down UP key.

The threshold level is shifted to low

value (high sensitivity) by pressing

down UP key.

Stable sensing is not possible

PRO MODE

●When MODE indicator: PRO (yellow) lights up, PRO mode can be set.

●For detail of PRO mode, refer to “ PRO MODE OPERATION MANUAL.”

Procedure

<PRO1>

Shift amount setting

Timer setting

Responce time setting

Hysteresis setting

Emission power setting

Timer range setting

Teaching lock setting

Setting items in digital display setting

Setting of digital display turning

Time period hold setting

Data bank loading setting

Back up setting

Communication protocol setting

Copy lock setting

Copy action setting

Data bank saving setting

<PRO3>

<PRO4>

Copy setting

<PRO2>

ECO setting

Display adjustment setting

Setting of threshold value tracking

<PRO5>

Code setting

<PRO6>

Reset setting

CUSTOM setting

Interference prevention setting

Sensing output setting

<PRO7>

Logic operation setting

SET

DOWN (

) key (select)

MODE indicator PRO (Yellow)

MODE key

UP (+) key (select)

SET key (conrm)

8THRESHOLD VALUE FINE ADJUSTMENT FUNCTION

● Set the ne adjustment of threshold value in RUN mode.

● Also, the threshold value ne adjustment function can be used in forced ON

output mode and forced OFF output mode.

●For setting of the sensing output, refer to “PRO MODE OPERATION MANUAL.”

●When setting sensing output to the window comparator mode or hysteresis

mode, “ ” and “ ” can be changed to another by pressing down

SET key for 2 sec.

In case conducting threshold value ne adjustment of “ ” or “ ”, press

down UP key or Down key, and “ ” or “ ” are displayed. Then, the

threshold value ne adjustment can be conducted.

Note: It may not respond when values of “ ” and “ ” are close because of relation of hysteresis. Be sure

to conrm with this device.

9KEY LOCK FUNCTION

●The key lock function prevents key operations so that the conditions set in

each setting mode are not inadvertently changed.

●If operating key switch after key lock is set, “ ” is indicated on the

digital display.

SENSING OUTPUT OPERATION MODE

●When MODE indicator: L / D (yellow) lights up, sensing output operation can be set.

CUSTOM MODE

●When MODE indicator: CUST (yellow) lights up,

Response time setting, Emission power setting

or Hysteresis setting can be displayed.

For the setting procedure, refer to “PRO MODE

OPERATION MANUAL.”

●By pressing UP key or DOWN key, the setting in

each item will be changed.

● Press SET key to conrm the setting.

●For setting of each item, refer to the following table.

Item Digital display Reference item

Response time setting <PRO 1: Response time setting>

Emission power setting <PRO 1: Emission power setting>

Hysteresis setting <PRO 1: Hysteresis setting>

MODE indicator

CUST (Yellow)

UP key

SET key DOWN key

MODE key

Automatic

Press down for

3 sec. or more

are displayed

Press down for

3 sec. or more

Automatic

Press down

SET key

Press down

UP / DOWN key

Conrmed

Press down

UP / DOWN key

Press down

SET key

Automatically set without pressing

down SET key in approx. 2 sec.

Press down

UP / DOWN key

Press down

SET key

Press down

UP / DOWN key

Conrmed

Automatically set without pressing

down SET key in approx. 2 sec.

Produktspecifikationer

Varumärke:	Panasonic
Kategori:	Inte kategoriserad
Modell:	FX-501

Behöver du hjälp?

Om du behöver hjälp med Panasonic FX-501 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Panasonic Manualer

Panasonic FX-501 Bruksanvisning

7 Januari 2025

Panasonic AW-PS551PJ Bruksanvisning

4 Januari 2025

Panasonic AK-HCU250PSJ Bruksanvisning

26 December 2024

Panasonic DMW-LMCH62E Bruksanvisning

22 December 2024

Panasonic DMW-GMC1 Bruksanvisning

22 December 2024

Panasonic DMW-AVC1 Bruksanvisning

22 December 2024

Panasonic SC-XH100 Bruksanvisning

22 December 2024

Panasonic NB-W250 Bruksanvisning

20 December 2024

Panasonic MultiShape ER-CKN3 Bruksanvisning

20 December 2024

Panasonic DMW-YAGH Bruksanvisning

11 December 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Milwaukee 48-22-8426 Bruksanvisning

8 Januari 2025

Smartwares 10.051.84 Bruksanvisning

8 Januari 2025

Sony Clié PEGA-UC60K Bruksanvisning

8 Januari 2025

IFM RU1088 Bruksanvisning

8 Januari 2025

Uniden WBR2-G54 Bruksanvisning

8 Januari 2025

Bestway 43644 Bruksanvisning

8 Januari 2025

Pyle PDWM2950 Bruksanvisning

8 Januari 2025

Makita MR007GZ Bruksanvisning

8 Januari 2025

Cisco EPQ2160 Bruksanvisning

8 Januari 2025

LevelOne CAS-3101 Bruksanvisning

8 Januari 2025