Philips Mistral Elan HI284 Bruksanvisning

Philips Inte kategoriserad Mistral Elan HI284

Läs nedan 📖 manual på svenska för Philips Mistral Elan HI284 (50 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/50
3
J
1
MAX
M
L
A
N
A
S
E
T
S
E
L
F
C
L
E
A
N
A C B
EF H I KD N L
G
HI 292
HI 294
4
Important
Please read these instructions in conjunction with the
illustrations before using the appliance.
Before using for the first time, check if the voltage rating on
the typeplate corresponds to the mains voltage in your home.
Never use the appliance if it is damaged in any way.
Take care that children cannot touch the iron when hot and
that they cannot pull the mains cord.
The ejected steam is hot and therefore hazardous. Never direct
the steam towards people.
Remove the plug from the socket before filling the iron with
water or pouring out the remaining water after use.
Never immerse the iron in water.
When you have finished ironing, and also when leaving the
iron even for a short while:
- set the steam control to position O;
- put the iron in upright position;
- remove the mains plug from the wall socket.
Note: The soleplate may become seriously corroded if the iron
is stored with the soleplate facing downwards.
Some parts of the iron have been slightly greased and as a
result the iron may slightly smoke when switched on for the
first time. After a short while, however, this will cease.
Before using the first time remove any sticker or protective foil
from the soleplate. Clean the soleplate with a soft cloth.
Do not put vinegar or other descaling agents into the water
reservoir.
Do not use chemically descaled water.
The cordset should not be allowed to touch the soleplate when
it is hot.
If the mains cord of this appliance is damaged, it must be
replaced by the original type only.
Please apply to your Philips dealer or to the Philips
organisation in your country for replacement.
English
5
General description (fig. 1)
ATemperature control (rotate)
BSteam control (rotate)
O= no steam
N= normal steam
H= extra steam
1 SELF CLEAN = self-cleaning / descaling, removing steam control
needle
CSpray button T (press)
DShot of Steam button s (press)
ESpray
FFilling aperture
GSoleplate
HWater reservoir with level indication
ITemperature pilot light (amber)
JType plate
KCord winder
LCord clip
MMeasuring beaker
N"Auto Stop" pilot light (red)
(with types HI 292 and HI 294 only)
Filling with water (for steam-ironing and spraying)
Please fill this iron with normal tap water before using for the first time.
For refilling, you can also use tapwater. However, if the water is very
hard (hardness higher than 17 °DH / 21
14°Clarke), it is advisable to
use distilled water.
- Remove the mains plug from the wall socket before filling the iron.
Set the steam control to position (= no steam).O
- Stand the iron on its end and pour water into the filling aperture (fig. 2).
Use the measuring beaker with spout for this purpose.
Do not fill higher than marking on the water reservoir. "MAX"
(Maximum filling = approx. 200 ml.)

Produktspecifikationer

Varumärke: Philips
Kategori: Inte kategoriserad
Modell: Mistral Elan HI284

Behöver du hjälp?

Om du behöver hjälp med Philips Mistral Elan HI284 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Philips Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer