Philips Norelco series 5000 HC3422 Bruksanvisning

Philips Gräsklippare Norelco series 5000 HC3422

Läs nedan 📖 manual på svenska för Philips Norelco series 5000 HC3422 (1 sidor) i kategorin Gräsklippare. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

If you are not fully satisfied with your Philips Norelco

Clipper, send the product back and we’ll refund you the

full purchase price.

Delivery of refund check will occur 6–8 weeks AFTER

receipt of returned product.

Make sure that the flat part of the comb is

always in full contact with the scalp to obtain

an even result (fig. 7).

Since all hairs do not grow in the same

direction, move the appliance slowly over the

crown from different directions (i.e. upwards,

downwards and across) to achieve an even

result.

Always move the appliance against the

direction of hair growth.

Make overlapping passes over the head to

ensure that all hair that should be cut has

been cut.

For best results with curly, sparse or long

hair, use a styling comb to guide the hair

towards the Clipper.

Turn the Clipper off regularly during clipping

and remove the hair clipping comb to blow

and/or shake out hair that has accumulated.

Use the Clipper without a comb to clip hair

very close to the skin (0.5mm/1/32 inch) or to

contour the neckline and area around the ears.

Remove the hair clipping comb by pressing

and sliding the comb off the Clipper (fig. 8).

Be careful when you are clipping without comb

attachment as when the Clipper is turned on it

will remove every hair it touches.

To contour the hairline around the ears,

comb the hair ends over the ears.

Tilt the Clipper in such a way that only

one edge of the cutter blades touches the

hair ends when you shape the contours

around the ears.

Only cut the hair ends. The hairline should be

close to the ear.

To contour the nape of the neck or

sideburns, turn the Clipper and make

downward strokes (fig. 9).

Move the Clipper slowly and smoothly

following the natural hairline.

Clean the attachments after each use.

Always switch Clipper OFF, unplug and remove

power supply cord from Clipper before

cleaning.

Do not use compressed air, abrasive cleaning

agents, scourers or aggressive liquids such as

alcohol, benzene, bleach or acetone to clean

the Clipper and attachments.

Never clean, replace or remove Clipper

attachments with motor ON.

Never rinse or immerse the Clipper in water

or any other liquid.

Do not apply pressure to cutters.

Do not touch cutters with hard objects as this

may damage them.

If cut hairs have accumulated in the comb

area, remove hairs by shaking, blowing or using

cleaning brush provided.

Make sure the Clipper is switched OFF

and disconnected from the electrical outlet.

Remove the hair clipping comb by pressing

and sliding the comb off the Clipper (fig. 8).

Clean the comb with the brush supplied or

rinse under warm water (fig. 10).

Press the release button (1) and remove the

cutting unit (2) (fig. 11).

Clean the cutting unit with the brush

supplied or rinse under warm water (fig. 12).

Clean the inside of the Clipper with the

brush supplied (fig. 13).

Shake off any excess water and allow to

air dry.

Reattach cutting unit by inserting the notch

of the cutting unit into the guiding slot.

Push the cutting unit back onto the Clipper.

Clean the handle and the adapter with a

soft, dry cloth.

NOTE: The Clipper does not need any lubrication.

The Charging Light on the appliance will

light up green continuously to indicate the

Clipper is charging (fig. 2).

It will take approximately 8 hours to fully

charge the Clipper for a cordless clipping

time of up to 75 minutes.

Disconnect the cord and unplug from

electrical outlet.

After the Clipper has been charged for the first

time, do not recharge the Clipper between

clipping sessions. Continue using it until the

battery is completely empty.

Do not charge for more than 24 hours.

Do not keep cord permanently plugged in.

Discharge/run down the battery completely

twice a year by letting the motor it run until

stops.

If the Clipper hasn’t been used for a long

period of time, it must be recharged for a

full 8 hours.

Only use the Clipper corded when the battery

is almost empty.

Clipper does not recharge during corded

clipping.

Connect cord provided to Clipper (fig. 1) and

plug Clipper into electrical outlet.

If battery is completely empty, wait a few

minutes before switching clipper ON.

Turn Clipper ON to begin clipping (fig. 3).

When finished clipping, turn Clipper OFF

and unplug.

Charge according to directions. Unplug

Clipper from outlet and remove cord.

Turn Clipper ON to begin clipping (fig. 3).

If the charge runs out while clipping, simply

connect cord provided to Clipper and outlet

to continue clipping.

Use this Clipper for its intended household

use as described in this manual.

Make sure that the appliance is fully charged

before you start clipping hair.

Before you start clipping, make sure that the

head of the person whose hair you are cutting

is at the same level as your chest so that all

parts of his/her head are clearly visible and

within easy reach.

Only use the appliance on clean, dry hair.

Do not use on freshly washed hair.

Before you begin, comb the hair in the direction

of growth (fig. 4).

To achieve optimal clipping results, always move

the appliance slowly through the hair against

the direction of hair growth.

Be certain the Clipper is in the OFF position.

Slide the hair clipping comb into the guiding

grooves on both sides of Clipper and push

until you hear it ‘click’ into place (fig. 5).

Make sure the comb locks properly into position.

Turn the Adjustable Hair Length Setting

Slide Switch to the desired setting (fig. 6).

The Clipper can cut hair up to 13 different

lengths. See table below.

The remaining hair length is indicated in

millimeters on the adjustable slide switch.

When you are clipping for the first time,

start at the maximum clipping length setting

(23mm/7/8 in.) to familiarize yourself with the

appliance and prevent accidentally trimming

hairs too short. As you become familiar with the

settings, adjust the Hair Length Slide Switch to

desired trimming length.

Press the release button (1) and remove the

cutting unit (2) (fig. 11).

Place the notch of the new cutting unit in

the guiding slot (1) and push the cutting unit

onto the Clipper (2) (fig. 14). You will hear

 a‛click’.

This Clipper has no other user-serviceable parts.

For assistance call 1-800-243-3050.

For assistance, call toll free:

Online information is available 24 hours a day,

7 days a week.

Be sure Clipper is turned OFF. Remove cord

from outlet and Clipper before storing in a

safe, dry location where it will not be crushed,

banged, or subject to damage.

Do not wrap cord around Clipper when

storing.

Store cord in a safe location where it will not

be cut or damaged.

Do not place or store Clipper where

it can fall or be pulled into a tub or sink, water

or other liquid while plugged in.

This Philips Norelco Clipper contains a

rechargeable Nickel Metal Hydride battery

which must be disposed of properly (fig. 15).

Battery should only be removed when

Clipper is to be discarded.

For assistance, visit our website,

www.philips.com/support or call

toll free: 1-800-243-3050.

Unplug electrical cord from outlet and

Clipper before dismantling Clipper.

Allow Clipper to run until the battery is

empty/depleted.

Turn Clipper OFF.

Remove the hair clipping comb and cutting

unit from the handle.

Press the release button (1) and remove the

cutting unit (2) (fig. 16).

Insert the screwdriver between the motor

unit and the back panel of the appliance.

Press down the screwdriver as far as it will

go (fig. 17).

Tilt the handle of the screwdriver

downwards (1) and separate the back panel

from the appliance (2) (fig. 18).

Remove the back panel. Pull the bottom

part of the printed circuit board with the

rechargeable batteries attached from the

appliance (fig. 19).

Cut the wires to separate the rechargeable

batteries from the appliance (fig. 20).

Do not attempt to replace battery. Insulate

battery ends by covering with tape and/or

place battery in a small plastic bag.

Discard your Clipper. Do not attempt to

plug electrical cord into the outlet or

recharge the Clipper after the battery has

been removed.

Contact your local town or city officials

for battery disposal information or call

1-800-8-BATTERY or www.rbrc.com for

battery drop-off locations.

When using an electrical appliance, basic safety

precautions should always be followed, including

the following:

1. Do not reach for a clipper that has fallen into

water. Unplug immediately.

2. Use clipper only in dry condition. Do not use

while bathing or in a shower.

3. Do not submerge clipper in water.

4. Do not place or store clipper where it can

fall or be pulled into a tub or sink. Do not

place in or drop into water or other liquid.

5. Always unplug this clipper from the electrical

outlet immediately after using, except when

clipper is (re)charging.

6. Unplug clipper before cleaning.

7. When discarding clipper, unplug clipper to

remove rechargeable battery. See Battery

Removal instructions.

1. Close supervision is necessary when

this appliance is used by, on, or near children

or invalids.

2. Use this clipper for its intended household

use as described in this manual. Do not use

attachments not recommended by Philips

Electronics North America Corporation.

3. Never operate this clipper if it has a

damaged cord or plug, if it is not working

properly, if it has been dropped, damaged, or

dropped into water. For assistance visit our

website www.philips.com/norelco or call

1-800-243-3050.

4. Do not rinse or immerse the clipper handle

in water or any other liquid.

5. Keep the clipper, cord and any attachments

away from heated surfaces.

6. Never drop or insert any object into any

opening.

7. Do not operate, charge or plug in clipper

outdoors or where aerosol (spray) products

are being used or where oxygen is being

administered.

8. Always check cutters, cutting unit and comb

before using the clipper. Do not use the

clipper if cutters, cutting unit or comb are

damaged, as injury may occur.

9. Always attach plug to clipper first, then to

outlet. To disconnect, turn on/off switch to

“OFF” position, then remove plug from

outlet.

10. To prevent possible damage to the cord, do

not wrap cord around the clipper.

11. Use only the cord provided to charge and

(re)charge clipper.

12. Never put clipper in direct sunlight or store

at a temperature above 140°F.

13. This clipper is for use on human hair only.

Do not use this clipper for any other

purpose.

14. Only use the power plug and other

accessories supplied with the clipper.

Congratulations on your purchase and welcome

to Philips Norelco!

To fully benefit from the support that Philips

Norelco offers, register your product at

www.norelco.com/register

Like many new products, your Philips Norelco Hair

Clipper may take a little getting used to. If you are

using an electric Clipper for the first time, or if

you’ve been using a different brand, take the time

to acquaint yourself with your new Hair Clipper.

Your Hair Clipper features a double-sharpened

steel cutting element with reduced friction.

Throw your scissors away and put your new

Hair Clipper to the test. We guarantee precise

results or Norelco will refund you the full Philips

purchase price as long as the request is received

within 45 days of purchase.

HC3422

Rechargeable

Cordless/Cord

Philips Electronics North America Corporation warrants each new Philips

Norelco product, Model HC3422 (except cutters and comb) against

defects in materials or workmanship for a period of two years from the

date of purchase, and agrees to repair or replace any defective product

without charge.

This warranty does not cover damage resulting from

accident, misuse or abuse, lack of reasonable care, the affixing of any

attachment not provided with the product or loss of parts or subjecting

the product to any but the specific voltage.* Use of unauthorized

replacement parts will void this warranty.

In order to obtain warranty service, simply go to www.philips.com/

norelco or call 1-800-243-3050 for assistance. It is suggested that for

your protection you return shipments of product by insured mail,

insurance prepaid. Damage occurring during shipment is not covered by

this warranty. No other warranty, written or oral, is authorized

by Philips Electronics North America Corporation. This warranty gives

you specific legal rights, and you may also have other rights which vary

from state to state. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above exclusion and

limitations may not apply to you.

*Read enclosed instructions carefully.

Manufactured for:

Philips Consumer Lifestyle

A Division of Philips Electronics North America Corporation

P.O. Box 10313, Stamford, CT 06904

This symbol on the product’s nameplate means it is

listed by Underwriters’ Laboratories, Inc.

Norelco is a Registered Trademark of Philips Electronics

North America Corporation.

PHILIPS is a Registered Trademark of Koninklijke Philips N.V.

www.norelco.com/register

HAIRCLIPPER 5200

S E R I E S 5 0 0 0

Fully charge Clipper before using for the first

time or after non-use a long period of time.for

Battery performance is best if you recharge

only when the battery is (almost) completely

empty.

Charging, recharging or using Clipper at

 temperaturesbelow40˚Forhigherthan95˚F

adversely affects lifespan of the battery.

Continuously recharging Clipper will reduce

lifespan of battery.

Be certain Clipper is OFF.

Insert the appliance plug directly into the

Clipper (fig. 1) and plug the adapter into any

120V AC outlet. Use only the cord provided.

A Hair Clipping Comb

B Cutting Unit

C Adjustable Hair Length Setting Slide Switch

D On/Off Button

E Charging Light

F Socket for Appliance Plug

G Cleaning Brush

H Adaptor

I Appliance Plug

J Storage Case

Full Two-Year Warranty

45-Day Money-Back Guarantee

Produktspecifikationer

Varumärke:	Philips
Kategori:	Gräsklippare
Modell:	Norelco series 5000 HC3422

Behöver du hjälp?

Om du behöver hjälp med Philips Norelco series 5000 HC3422 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Gräsklippare Philips Manualer

Philips Norelco BG7040 Bruksanvisning

22 September 2024

Philips Norelco BG5025 Bruksanvisning

22 September 2024

Philips Norelco series 5000 HC3422 Bruksanvisning

21 September 2024

Philips Series 7000 QG3380 Bruksanvisning

14 September 2024

Philips Series 7000 QC5390 Bruksanvisning

14 September 2024

Philips Series 5000 BG5020 Bruksanvisning

2 September 2024

Philips Series 7000 HC7650 Bruksanvisning

12 Augusti 2024

Philips Series 3000 QG3334 Bruksanvisning

9 Augusti 2024

Philips Multigroom QG410 Bruksanvisning

8 Augusti 2024

Philips QC5572 Bruksanvisning

15 Juli 2024

Gräsklippare Manualer

Nyaste Gräsklippare Manualer

Masport President 1000ST Combo Bruksanvisning

27 Oktober 2024

Saturn ST-HC7381 Bruksanvisning

27 Oktober 2024

Viking MI 632 P Bruksanvisning

27 Oktober 2024

Baumr-AG 480ZRX Bruksanvisning

26 Oktober 2024

Honda HRH 536 HX Bruksanvisning

26 Oktober 2024

Alpina AL4 51 S Li Bruksanvisning

23 Oktober 2024

Al-ko Highline 42.5 P-A Bruksanvisning

22 Oktober 2024

Al-ko 5235 SP-A Bruksanvisning

22 Oktober 2024

Stiga Combi 55 SVQ H Bruksanvisning

21 Oktober 2024

Flymo SimpliGlide 360 Bruksanvisning

21 Oktober 2024