Pioneer SPH-DA250DAB Bruksanvisning

Pioneer bilradio SPH-DA250DAB

Läs nedan 📖 manual på svenska för Pioneer SPH-DA250DAB (47 sidor) i kategorin bilradio. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/47

English Français Italiano Español Deutsch Nederlands

SPH-DA250DAB

RDS AV RECEIVER

AUTORADIO MULTIMÉDIA RDS

SINTOLETTORE AV CON RDS

AV RECEPTOR RDS

RDS-AV-RECEIVER

RDS AV-ONTVANGER

Installation Manual

Manuel d'installation

Manuale d'installazione

Manual de instalación

Installationsanleitung

Installatiehandleiding

2En

•Do not operate this product, any

applications, or the rear view camera

option (if purchased) if doing so will

divert your attention in any way from the

safe operation of your vehicle. Always

observe safe driving rules and follow all

existing traffic regulations. If you

experience difficulty in operating this

product, pull over, park your vehicle in a

safe location and apply the handbrake

before making the necessary

adjustments.

•Do not install this product where it may

(i) obstruct the driver’s vision,

(ii) impair the performance of any of the

vehicle’s operating systems of safety

features, including airbags, hazard lamp

buttons, or

(iii) impair the driver’s ability to safely

operate the vehicle.

In some cases, it may not be possible to

install this product because of the vehicle

type or the shape of the vehicle interior.

WARNING

Pioneer does not recommend that you

install this product yourself. This product is

designed for professional installation only.

We recommend that only authorised

Pioneer service personnel, who have

special training and experience in mobile

electronics, set up and install this product.

NEVER SERVICE THIS PRODUCT YOURSELF.

Installing or servicing this product and its

connecting cables may expose you to the

risk of electric shock or other hazards, and

can cause damage to this product that is

not covered by warranty.

WARNING

Do not take any steps to tamper with or

disable the handbrake interlock system

which is in place for your protection.

Tampering with or disabling the

handbrake interlock system could result in

serious injury or death.

CAUTION

•Secure all wiring with cable clamps or

electrical tape. Do not allow any bare

wiring to remain exposed.

•Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger

compartment into the engine

compartment. If the yellow lead’s

insulation tears as a result of contact with

metal parts, short-circuiting can occur,

resulting in considerable danger.

•It is extremely dangerous to allow cables

to become wound around the steering

column or gearstick. Be sure to install this

product, its cables, and wiring away in

such so that they will not obstruct or

hinder driving.

Connection

Precautions

Your new product and this

manual

Important safeguards

Precautions before

connecting the system

•Make sure that the cables and wires will

not interfere with or become caught in

any of the vehicle’s moving parts,

especially the steering wheel, gearstick,

handbrake, sliding seat tracks, doors, or

any of the vehicle’s controls.

•Do not route wires where they will be

exposed to high temperatures. If the

insulation heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

•Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse

resistor or filter, etc.) may fail to work

properly.

•Never feed power to other electronic

products by cutting the insulation of the

power supply lead of this product and

tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

•Use this product with a 12-volt battery

and negative earthing only. Failure to do

so may result in a fire or malfunction.

•To avoid shorts in the electrical system,

be sure to disconnect the (–) battery

cable before installation.

WARNING

•When speaker output is used by 4

channels , use speakers over 50 W

(Maximum input power) and between 4

Ω to 8 Ω (impedance value). Do not use 1

Ω to 3 Ω speakers for this unit.

•When rear speaker output is used by 2 Ω

of subwoofer, use speakers over 70 W

(Maximum input power).

*Please refer to connection for a

connection method.

•The black lead is earth. Please earth this

lead separately from the earth of high

current products such as power amps. Do

not earth more than one product

together with the earth from another

product. For example, you must

separately earth any amp unit away from

the earth of this product. Connecting

earths together can cause a fire and/or

damage the products if their earths

became detached.

•When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

•This product cannot be installed in a

vehicle without ACC (accessory) position

on the ignition switch.

•To avoid short-circuiting, cover the

disconnected lead with insulating tape. It

is especially important to insulate all

unused speaker leads, which if left

uncovered may cause a short circuit.

•For connecting a power amp or other

devices to this product, refer to the

manual for the product to be connected.

•The graphical symbol placed on

the product means direct current.

•When the ignition switch is turned on

(ACC ON), a control signal is output

through the blue/white lead. Connect to

an external power amp’s system remote

Before installing this

product

To prevent damage

Notice for the blue/

white lead

ACC position No ACC position

3En

English

control terminal, the auto-aerial relay

control terminal, or the aerial booster

power control terminal (max. 300 mA 12

V DC). The control signal is output

through the blue/white lead, even if the

audio source is switched off.

Microphone 3 m

Wired remote input

Hard-wired remote control adapter can

be connected (sold separately).

This product

Digital Radio aerial input

Aerial jack

Subwoofer output (STD)/Low range

output (NW)

Rear output (STD)/Middle range output

(NW)

Front output (STD)/High range output

(NW)

Power supply

Fuse (10 A)

To power supply

Depending on the kind of vehicle, the

function of 2* and 4* may be different.

In this case, be sure to connect 1* to 4*

and 3* to 2*.

Yellow (2*)

Back-up (or accessory)

Yellow (1*)

Connect to the constant 12 V supply

terminal.

Red (4*)

Accessory (or back-up)

This product

Power cord Red (3*)

Connect to terminal controlled by

ignition switch (12 V DC).

Connect leads of the same colour to

each other.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

Blue/white (5*)

The pin position of the ISO connector

will differ depending on the type of

vehicle. Connect 5* and 6* when Pin 5 is

an aerial control type. In another type of

vehicle, never connect 5* and 6*.

Blue/white (6*)

Connect to auto-aerial relay control

terminal (max. 300 mA 12 V DC).

Blue/white

Connect to system control terminal of

the power amp (max. 300 mA 12 V DC).

Violet/white

Of the two lead wires connected to the

back lamp, connect the one in which

the voltage changes when the gear shift

is in the REVERSE (R) position. This

connection enables the unit to sense

whether the car is moving forwards or

backwards.

Light green

Used to detect the ON/OFF status of the

handbrake. This lead must be

connected to the power supply side of

the handbrake switch.

Connection method

Clamp the lead (1) then clamp firmly

with needle-nosed pliers (2).

Power supply side

Handbrake switch

Earth side

Speaker leads

White: Front left + or high range left +

White/black: Front left – or high range

left –

Grey: Front right + or high range right +

Grey/black: Front right – or high range

right –

Green: Rear left + or middle range left +

Green/black: Rear left – or middle range

left –

Violet: Rear right + or middle range

right +

Violet/black: Rear right – or middle

range right –

ISO connector

In some vehicles, the ISO connector

may be divided into two. In this case, be

sure to connect to both connectors.

NOTES

•The position of the handbrake switch

depends on the vehicle model. For

details, consult the vehicle Owner’s

Manual or dealer.

•When a subwoofer is connected to this

product instead of a rear speaker, change

the rear output setting in the initial

setting. The subwoofer output of this

product is monaural.

•When using a subwoofer of 2 Ω, be sure

to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and

green/black leads.

Important

The speaker leads are not used when this

connection is in use.

Power amp (sold

separately)

Without internal amp

Produktspecifikationer

Varumärke:	Pioneer
Kategori:	bilradio
Modell:	SPH-DA250DAB
Färg på produkten:	Zwart
Inbyggd display:	Ja
Vikt:	101 g
Höjd:	0.87 "
Användarmanual:	Ja
Husmaterial:	Kunststof
På / Av knapp:	Ja
Beeldscherm:	LED
Skärm diagonal:	2.2 "
Vormfaktor:	Rechthoek
Frekvensband:	2.4 GHz
Inbyggda högtalare:	Nee
Antal batterier/batterier som stöds:	2
Gränssnitt:	IR Draadloos
Plug and play:	Ja
Indikation på lågt batteri:	Ja
Antal per paket:	1 stuk(s)
Antal knappar:	54
Maximal räckvidd:	10 m
Bakgrundsbelysta nycklar:	Ja
Bakgrundsbelysning-färg:	Blauw
Klockfunktion:	Ja
Accucapaciteit:	Ja
Batteriladdningsindikering:	Ja
Ingångstyp:	Drukknopen
Korrekt användning av fjärrkontrollen:	AUX1, AUX2, Projection screen, Projector, SAT, TV, VCR
Djup (kejserligt):	8.7 "
Antal-produkter-ingår:	2.2 stuk(s)
Batterityp:	AAA
Bakgrundsbelyst display:	Ja
Antal enheter som stöds:	8
Lärbara IR-koder:	Ja
Anpassningsbara knappar:	Ja
Markörknapp:	Ja
Vridknapp:	Nee