Planet IGS-504PT Bruksanvisning

Läs nedan 📖 manual på svenska för Planet IGS-504PT (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET IGS-504PT Industrial 5-Port
Gigabit Ethernet Switch with 4 PoE+ ports. The interfaces of
these models are shown below:
In the following section, the term Industrial PoE+ Switch”
means the IGS-504PT. Open the box of the Industrial PoE+
Switch and carefully unpack it. The box should contain the
following items:
Industrial PoE+ Switch x 1 Users Manual x 1
Wall-mount Kit x 1 DIN-rail Kit x 1 RJ45 Dust Caps x 5
If any of these are missing or damaged, please contact your
dealer immediately.
Switch Specications
Switch
Architecture Store-and-Forward
Switch Fabric 10Gbps
Throughput
(packet per
second)
7.4Mpps@64bytes
Address Table 2K entries
Jumbo Frame 9Kbytes
Flow Control Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Power over Ethernet
PoE Standard
IEEE 802.3at Power over Ethernet Plus/PSE
Backward compatible with IEEE 802.3af
Power over Ethernet/PSE
PoE Power
Supply Type End-span
Power Pin
Assignment 1/2(+), 3/6(-)
PoE Power
Output
Per port 48-54V DC
Max. 30 watts@54V DC
Max. 15 watts@48V DC
PoE Power
Budget
Max. 120 watts@54V DC
Max. 60 watts@48V DC
Max. Number
of Class 4 PDs 4
3.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one
terminal block connector within two DC power inputs.
Figure 3-2 shows the upper panel of the Industrial PoE+
Switch.
DC Input Range:
48-54V
, 3A max.
V1+ V2+
PWR1 PWR2
1 2 3 4
Figure 3-2: Industrial PoE+ Switch Upper Panel
3.4 Wiring the Power Inputs
The 4-contact terminal block connector on the top panel of
Industrial PoE+ Switch is used for two DC redundant power
inputs. Please follow the steps below to insert the power wire.
When performing any of the procedures like
inserting the wires or tightening the wire-clamp
screws, make sure the power is OFF to prevent
from getting an electric shock.
3. Hardware Introduction
3.1 Switch Front Panel
P1 P2
1
2
3
4
5
ACTLNK
PoE-in-Use
Gigabit Ethernet TP Interface
10/100/1000BASE-T copper, RJ45
twisted-pair: Up to 100 meters.
Figure 3-1:
IGS-504PT Front View
2.ProductSpecications
Model IGS-504PT
Hardware Specications
Copper Ports 5 10/100/1000BASET RJ45 auto-MDI/MDI-X
ports
PoE Injector
Ports
4 ports with 802.3at PoE+ injector function
(Ports 1 to 4)
PoE Budget 120W maximum@75 degrees C
Connector Removable 4-pin terminal block
Pin 1/2 for Power 1; Pin 3/4 for Power 2
Power
Requirements
48~54V DC, 3A (max.)
Redundant power with reverse polarity
protection function
Power
Consumption
DC 48V:
Max. 0.48 watts/1.63BTU (System)
Max. 62.88 watts/214.5BTU (Full Loading)
DC 54V:
Max. 0.54 watts/1.84BTU (System)
Max. 123.12 watts/420BTU (Full Loading)
Dimensions
(W x D x H) 30 x 70 x 104 mm
Weight 260g
Enclosure IP30 metal case
Installation DIN-rail kit and wall-mount kit
ESD Protection 6KV
Standards Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Stability
Testing
IEC 60068-2-32 (free fall)
IEC 60068-2-27 (shock)
IEC 60068-2-6 (vibration)
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3x Full-Duplex Flow Control
IEEE 802.3az Energy Ecient Ethernet (EEE)
IEEE 802.3at Power over Ethernet Plus PSE
IEEE 802.3af Power over Ethernet Plus
IEEE 802.1p Class of Service
Environment
Temperature Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity Operating: 5~90% (non-condensing)
Storage: 5~90% (non-condensing)
3.2 LED Indicators
System
LED Color Function
P1 Green Lights to indicate power 1 has power.
P2 Green Lights to indicate power 2 has power.
Per 802.3at PoE+ 10/100/1000BASE-T Interface (Port
1 to Port 4)
LED Color Function
LNK/
ACT Green
Lights to indicate the link through
that port is successfully established at
10/100/1000Mbps.
Blinks to indicate that the Switch is
actively sending or receiving data over that
port.
PoE-
in-Use Amber
Lights to indicate the port is providing DC
in-line power.
O to indicate the connected device is not
a PoE powered device (PD).
Per 10/100/1000BASE-T Interface (Port 5)
LED Color Function
LNK/
ACT Green
Lights to indicate the port is successfully
established at 10/100/1000Mbps.
Blinks to indicate that the Switch is actively
sending or receiving data over that port.
1. The DC power input range is 48V
~ 54V DC. Please insert
positive and negative DC power wires into contacts 1 and 2
for POWER 1, or 3 and 4 for POWER 2.
DC Input Range:
48-54V
, 3A max.
V1+ V2+
PWR1 PWR2
1 2 3 4
Figure 3-3: Industrial PoE+ Switch DC Input
DC Input Max. PoE Budget
48V~51V 60 watts
52V~54V 120 watts
Note
1. To avoid damage, please use the Industrial PoE+
Switch according to its specifications.
2. Please follow the table above for DC input in
relation with maximum PoE budget.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.5 Grounding the Device
Uses MUST complete grounding wired with the device;
otherwise, a sudden lightning could cause fatal damage to the
device.
Note
EMD (Lightning) DAMAGE IS NOT CONVERED
UNDER WARRANTY.
DC Input Range:
48-54V
, 3A max.
V1+ V2+
PWR1 PWR2
1 2 3 4
Earth Ground
4.2 Wall-mount Plate Mounting
4.3 Side Wall-mount Plate Mounting
You must use the screws supplied with the wall-
mounting brackets. Damage caused to the parts
by using incorrect screws would invalidate your
warranty.
4. Installation
This section describes the functionalities of the Industrial PoE+
Switchs components and guides you to installing it on the
DIN-rail and wall. Basic knowledge of networking is assumed.
Please read this chapter completely before continuing.
Note
This following pictures show how to install the
device. However, the device in the picture is not
IGS-504PT.
4.1 DIN-rail Mounting Installation
5. Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site rst to
check if it could solve your issue. If you need more support
information, please contact PLANET support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq?method=category&c1=3
Support team mail address:
support@planet.com.tw
Copyright © PLANET Technology Corp. 2021.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
FCC Warning
This device has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense
WEEE Warning
To avoid the potential eects on the environment and
human health as a result of the presence of
hazardous substances in electrical and electronic
equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
PLANET TECHNOLOGY CORPORATION
e-mail: sales@planet.com.tw http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan Tel:886 2219 9518 Fax:886 2219 9528-2- - -2- -
EC Declaration of Conformity
For the following equipment:
*Type of Product : -Port 10/100/1000T 802.3at PoE + 1-Port 10/100/1000T Industrial Compact 4
Ethernet Switch
*Model Number : -504PTIGS
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on
2014/30/EU.
For the evaluation regarding the EMC, the following standards were applied:
EN 55032 2015+AC:2016
EN 55024 2010+A1:2015
EN 55035 2017
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Director
Taiwan
15
th
Apr., 2021
.
Place
Date
Legal Signature

Produktspecifikationer

Varumärke: Planet
Kategori: Inte kategoriserad
Modell: IGS-504PT

Behöver du hjälp?

Om du behöver hjälp med Planet IGS-504PT ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Planet Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer