Pyle INV239A Bruksanvisning

Pyle mottagare INV239A

Läs nedan 📖 manual på svenska för Pyle INV239A (18 sidor) i kategorin mottagare. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/18
Invincible Series Amplifier
www.PyleUSA.com
2
INTRODUCTION
PYLE ampliers provides high-performance sound reinforcement for your
mobile audio equipment. Its versatility enables compatibility with optional
Equalizers, Frequency Dividing Crossover Networks, and other audio processors
in customized system. The Multi-Mode bridging capabilities allow exibility in
hosting several dierent speaker congurations.
To achieve optimum performance, it is highly recommended that you read this
Owners Manual before beginning installation.
WARNING!
High powered audio systems in a vehicle are capable of generating "Live Concert
high levels of sound pressure. Continued exposure to excessively high volume
sound levels may cause hearing loss or damage.
Also, operation of a motor vehicle while listening to audio equipment at high
volume levels may impair your ability to hear external sounds such as; horns,
warning signals, or emergency vehicles, thus contributing to a potential trac
hazard. In the interest of safety, PYLE recommends listening at lower volume
levels while driving.
TABLE OF CONTENTS
PLANNING YOUR SYSTEM
WIRING CONNECTION
PANEL LAYOUT
CONTROL FUNCTIONS
SPEAKER CONNECTION
TROUBLESHOOTING GUIDE
SPECIFICATION
3
3
5
8
10
16
17
www.PyleUSA.com 3
PLANNING YOUR SYSTEM
Before beginning the installation, consider the following
1. Do you plan to add additional mobile electronics equipment in the future?
If you plan to expand your system by adding other components sometime in
the future, ensure adequate space is left, and cooling requirements are met.
2. Should you use high or low level inputs?
Your Amplier has been designed to accept Low-Level (Pre-Amp outputs from
your radio) signal source. If your radio/source is equipped with Pre-Amp
outputs, it is possible to utilize them to drive the Amplier and connecting
(Amplier) to the 2 rear speakers. Then, use the built-in power of your radio to
drive the 2 front speakers.
3. Are your components matched?
The RMS power rating of your speakers must be equal or greater than the RMS
power rating of your amplier. You speaker(s) also must be 2- 8 Ohms
impedance for stable amplier operation. Impedance information is normally
printed on the speaker basket or magnet.
4. Where will the amplier be installed?
Consider both the length of your leads and routing when determining the
mounting location. It is best to run power and RCA wiring on opposite sides of
the vehicle to prevent induced noise. Pre-Amp input Jacks require a length
(depending on location) of high qualityshielded male to male RCA patch cord.
WIRING CONNECTION
CAUTION:
AS A PRECAUTION, DISCONNECT THE POWER WIRE FROM THE BATTERY
WHILE MAKING THE POWER AND GROUND CONNECTIONS TO THE AMPLFIER.
4/8 GAUGE (Thicker if planning for additional Ampliers) wire is recommended
for both the power and ground wires. 12 Gauge, For the remote turn-on wire, 16
Gauge. Both types are available at most Mobile Audio Dealers or Installation Shop.

Produktspecifikationer

Varumärke: Pyle
Kategori: mottagare
Modell: INV239A

Behöver du hjälp?

Om du behöver hjälp med Pyle INV239A ställ en fråga nedan och andra användare kommer att svara dig




mottagare Pyle Manualer

Pyle

Pyle PLA2200 Bruksanvisning

30 September 2024
Pyle

Pyle Pro PTAU23 Bruksanvisning

25 September 2024
Pyle

Pyle PTAU45.5 Bruksanvisning

22 September 2024
Pyle

Pyle PWMA3003BT Bruksanvisning

21 September 2024
Pyle

Pyle PLAM2001D Bruksanvisning

19 September 2024
Pyle

Pyle PT1100 Bruksanvisning

19 September 2024
Pyle

Pyle PFA100 Bruksanvisning

19 September 2024
Pyle

Pyle PDA35BT Bruksanvisning

19 September 2024
Pyle

Pyle PDC22 Bruksanvisning

19 September 2024

mottagare Manualer

Nyaste mottagare Manualer