Pyle PLMRSBA10 Bruksanvisning

Pyle mottagare PLMRSBA10

Läs nedan 📖 manual på svenska för Pyle PLMRSBA10 (5 sidor) i kategorin mottagare. Denna guide var användbar för 13 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/5
PLMRSBA10
Marine Grade Slim Active Subwoofer
10” 900 Watts Low-Prole Active Amplied Marine
and Waterproof Subwoofer System
Suitable for Under-seat Installations
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.PyleUSA.com
2www.PyleUSA.com 3
Introduction
With the , we are introducing a low-prole amplied subwoofer. Low enough PLMRSBA10
to easily t below the seat of your car. This system oers you a quick and easy way to add a
high-powered subwoofer system to your audio system.
The integrated amplier in the features low pass crossovers, and a control forPLMRSBA10
adjusting the input sensitivity from 0.12V to 3.5V.
Both high level (speaker level) and low level (RCA type) inputs are present, making this a
universal solution for use with any head unit or other input source.
For further exibility in the use of a subwoofer, a variable bass boost control has been
included. You can control the subwoofer level with the remote level control module.
Mounting the Subwoofer
1. Find a suitable location in the vehicle in which to mount the amplier.
A typical location is shown below:
2. Make sure there is sucient air circulation around the intended mounting location.
3. Mark the location for mounting hole screws by positioning the cabinet where you wish to
install it. Make a small mark to identify the position and remove the unit. Thoroughly clean
the area you plan to attach the subwoofer, using a vacuum cleaner and press down on it
securely.
Vehicle seat
Control Panel and Features
1. POWER ON LED INDICATOR
2. PROTECT LED INDICATOR
3. PHASE SHIFT: Use this switch to help compensate for time alignment problems in the
system. Such problems usually result from having the subwoofer at a dierent distance
from the listener than the other speakers in the system.
4. LOW PASS FILTER: This control permits you dene the frequency range you want the
subwoofer amplier to receive. The subwoofer will reproduce all sound BELOW the
frequency you set. If the rest of your system is weak on the mids, you may wish to set this
control relatively high. If the midrange is well covered by the rest of your system, you will
probably want the subwoofer to only receive lower frequency signal.
5. BASS BOOST: The bass boost feature will increase the sound level the bass frequencies.
6. INPUT GAIN CONTROL: After you have installed your system, turn this control to minimum.
Turn the head unit on (and the subwoofer will turn on via the remote connection).
Turn the head unit volume to about 2/3 full level. Slowly turn up the subwoofer input gain
control until you hear a small amount of distortion. Then reduce the level until the
distortion is completely gone. Leave the control at this setting.
7. REMOTE LEVEL CONTROL PORT: Attach the included remote level control to cotrol the
volume level of the subwoofer independently
8. HIGH LEVEL (speaker level) INPUTS: If your head unit does not have RCA outputs, you
can use the speaker outputs for the audio source for the PLMRSBA10. Use the supplied
cable and connect the outputs properly as shown in the connection diagram in this manual.
9. LOW LEVEL RCA INPUTS: Low level inputs are the recommended way to introduce the
audio signal to the subwoofer if RCA outputs are present on your head unit or other
signal source (such as a sound processor).
10. The fuse is rated at 25A. Do not use a fuse with a dierent value and FUSE: NEVER
replace the fuse with a wire or coin.
11. POWER TERMINALS
124 6 8 10 11
3 5 7 9
www.PyleUSA.com
4www.PyleUSA.com 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance.
Most trunk or hatchback installations will require a 15-20 foot RCA cable, while pickup trunks
and under-seat installations will require a 6-12 foot RCA cable. Always use a highquality
cable.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
High Level Input Wiring
The high level input(s) should only be used when your receiver lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver to the
high level input connector of the amplier. Be sure to observe polarity to avoid audio phase
problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
Power Connections
Connect the ground terminal to the closest point on the chassis of the vehicle.
Keep this ground wire to less than 39” (100 cm) inlength. Use 8 gauge (or heavier) wire.
Connect the remote terminal to the remote output of the head unit using 16 gauge
(or heavier) wire. Connect an empty fuse holder within 18” (45 cm) of the car battery, and run
8 gauge (or heavier) cable from this fuse to the amplier location. Then connect the fuse
holder to the “ ” connection on the subwoofer rear panel.BATT+
Remote Level Control Connection
Grey L+ Grey/Black L-
White R+ White/Black R-
To Speaker Terminals
of head unit
To Audio outputs of head
unit or signal processor Chassis ground point
To REMOTE TURN-ON
terninal of head unit
+
FUSE
Instal the remote control securely under the
dash or in a similar location where using it will
not distract the driver.
Remote
Level Control

Produktspecifikationer

Varumärke: Pyle
Kategori: mottagare
Modell: PLMRSBA10

Behöver du hjälp?

Om du behöver hjälp med Pyle PLMRSBA10 ställ en fråga nedan och andra användare kommer att svara dig


mottagare Pyle Manualer

Pyle

Pyle PLMRMBT5B Bruksanvisning

6 December 2024
Pyle

Pyle P3001AT Bruksanvisning

6 December 2024
Pyle

Pyle PFMRA340BB.5 Bruksanvisning

17 Oktober 2024
Pyle

Pyle PLA2200 Bruksanvisning

30 September 2024
Pyle

Pyle Pro PTAU23 Bruksanvisning

25 September 2024
Pyle

Pyle PTAU45.5 Bruksanvisning

22 September 2024
Pyle

Pyle PWMA3003BT Bruksanvisning

21 September 2024
Pyle

Pyle PLAM2001D Bruksanvisning

19 September 2024
Pyle

Pyle PT1100 Bruksanvisning

19 September 2024
Pyle

Pyle PFA100 Bruksanvisning

19 September 2024

mottagare Manualer

Nyaste mottagare Manualer

ETON

ETON MA 1 Bruksanvisning

19 Mars 2025
Elipson

Elipson P1 Bruksanvisning

14 Mars 2025
Elipson

Elipson Stream S300 Xi Bruksanvisning

14 Mars 2025
Elipson

Elipson WIIM Mini Bruksanvisning

14 Mars 2025
Rexing

Rexing RoadMate CPStream Bruksanvisning

13 Mars 2025
KanexPro

KanexPro SP-1X16SL18G Bruksanvisning

13 Mars 2025
Marshall Electronics

Marshall Electronics VDA-108-3GS Bruksanvisning

13 Mars 2025
Rega

Rega Brio MK7 Bruksanvisning

12 Mars 2025
Mtx Audio

Mtx Audio Thunder TH2500.1 Bruksanvisning

11 Mars 2025
Mtx Audio

Mtx Audio Thunder TH1500.1 Bruksanvisning

11 Mars 2025