Roland KD-200 Bruksanvisning

Roland Inte kategoriserad KD-200

Läs nedan 📖 manual på svenska för Roland KD-200 (1 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/1
Check the Included Items
After opening the package, check that all of the included items
are present. If anything is missing, contact your dealer.
Main unit
Wood hoop protector × 2
Connection cable
Drum key
Owner’s manual
* This package does not include a kick pedal or beater. A variety of
commercially available beaters can be used, including felt, plastic, or
wood types. However, if you use a felt beater, strike marks of the felt
might remain on the striking surface.
Descriptions
Front head
Hoop
Leg
fastener
knob
Rod
Foot nut
Foot
Leg
Shell
Tension bolt
Lug
Batter head’s strike surface
Batter board stopper
Hook
Batter board
Batter head
(inside)
TRIGGER OUT jack
Batter hoop
* Do not insert your hand or ngers into the gap between the batter
board and the batter head striking surface. Doing so might cause
injury, damage, or malfunction.
Assembling the KD-200
NOTE
During assembly, take care that the weight of the bass drum does not
pinch your hand or foot.
1. Loosen the leg fastener knob, adjust the angle of
the leg, and then tighten the leg fastener knob.
Using a drum key, adjust the length of the rods so that
the left and right are the same length.
Leg fastener knob
rod
2. Adjust the tip of the legs (spike/rubber)
appropriately for the surface on which you’re
placing the KD-200.
Spike Soft oor
Carpet, etc.
Rubber Hard oor
Wood ooring, concrete, etc.
If you loosen the foot nut and rotate the foot to raise it,
the spike will be exposed.
Tighten the foot nut to secure the position of the foot.
Foot nut
Foot
Spike
Spike Rubber
* The tip of the spike is sharp; handle it with care.
* Using the spike leg tips on wood ooring may damage the oor; the
rubber leg tips should be used on wood ooring.
3. Ax the wood hoop protectors to the position
at which the kick pedal is attached.
Ax to both surfaces of
the batter hoop
4. Mount the kick pedal.
Adjust the location at which the kick pedal is attached
so that the beater strikes the center of the batter head’s
strike surface; then securely fasten the kick pedal to the
KD-200.
* Take care not to pinch your ngers.
the center of Beater must hit
the striking surface
After attaching the kick
pedal, adjust the angle of
the legs and the length of
the rods as necessary.
Using Double Kick Pedals
The KD-200 can also be used with double kick pedals.
Adjust the striking points of the two beaters so that they are at
equal distances to the left and right of the batter head’s strike
surface.
Correct Incorrect
If the beater’s striking point cannot be aligned appropriately
Depending on the kick pedal, it might not be possible to attach
it to the bass drum so that the strike point of the two beaters is
located symmetrically to the left and right of the center of the
batter head’s strike surface.
In this case, use the following procedure to adjust the position of
the batter head’s strike surface.
1. Remove all of the hooks/tension bolts, the batter
board stopper, and the batter hoop.
Batter board
Batter board stopper
Tension bolt
Hook
Batter head
Batter hoop
NOTE
To avoid injury, damage, or malfunction, do not detach the batter
board and batter head from the shell. Take care not to injure your
hands or feet while working.
2. Turn the batter head together with the batter
board, and adjust it so that the center of the
TRIGGER OUT jack is near the location shown in
the illustration.
Batter board
Batter head
(approximate)
3. Place the batter hoop back.
4. Attach the batter board stopper to the hooks/
tension bolts.
Hook / Tension bolt
Batter board stopper
5. Alternating between opposite sides and using
your ngers to press the hooks and batter board
stoppers A, insert the tension bolts into the lugs
while pressing the batter board stoppers A in
between the batter hoop B and the batter board
C.
Batter board stopper A
Batter board C
Batter hoop B
Push down
6. Working alternately across opposite sides of the
drum, lightly tighten each tension bolt until the
hooks do not wobble.
5
7
3
4
1
26
8
7. Then tighten each tension bolt another 3/4 of a
turn to secure the front head.
* If the batter head is not secured suciently, the sensor might
malfunction, or the sound of the strike might be too loud.
Connecting to the Drum Sound Module
Connect the KD-200 to your drum sound module.
Use the included connection cable to make the connection.
Connect the “L” plug of the connection cable to the jack of the
KD-200.
(Example) TD-50
“I” plug KICK
“L” plug
Recommended Parameter Settings
These are the recommended values for the trigger parameters
when using the KD-200 with various drum sound modules.
If the “PAD TYPE” or “TRIG TYPE” of your drum sound module
provides a “KD200” setting, choose “KD200.” If “KD200” is not one
of the available values, refer to the support information on the
Roland website.
http://roland.cm/trigger_prm
You may need to adjust the trigger parameters depending on
how you’ve mounted the KD-200 and the location at which
you’ve installed it.
For details on editing refer to the owner’s manual of your drum
sound module.
Adjusting the Head Tension
Adjust the tension of the batter head before you play the KD-200.
You can vary the strike response (playing feel) by adjusting the
tension.
1. Adjust each tension bolt little by little, working
back and forth across the head in the order
shown in the illustration.
1
2
3
4
5
7
8
6
Batter head
Tension bolt
* Fully tightening a tension bolt at only a single location will produce
uneven tensioning, which will make it impossible to achieve correct
strike response and may also cause malfunctions.
2. Adjust each tension bolt so that the head is
tensioned evenly.
Main Specications
Roland KD-200: Bass drum
Shell 20 (Diameter) x 16 (Depth) inches
Wood shell
Trigger 1 (Head)
Acceptable
pedal Single pedal, Twin pedal
Connector TRIGGER OUT jack
Dimensions
633 (W) ×507 (D) ×528 (H) mm
24-15/16 x 20 x 20-13/16 inches
*When storing the legs
Weight 10.9 kg
24-15/16 x 20 x 20-13/16 inches
* This document explains the specications of the product at the time
that the document was issued. For the latest information, refer to the
Roland website.
Before using this unit, carefully read the leaet “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the
document(s) where it will be available for immediate reference.
English
Owner’s Manual
© 2020 Roland Corporation
KD-200
* 5 1 0 0 0 6 8 8 0 4 - 0 1 *

Produktspecifikationer

Varumärke: Roland
Kategori: Inte kategoriserad
Modell: KD-200

Behöver du hjälp?

Om du behöver hjälp med Roland KD-200 ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad Roland Manualer

Roland

Roland SD-20 Bruksanvisning

16 Oktober 2024
Roland

Roland FR-18 Diatonic Bruksanvisning

15 Oktober 2024
Roland

Roland RD-300GX Bruksanvisning

13 Oktober 2024
Roland

Roland Fantom FA-76 Bruksanvisning

12 Oktober 2024
Roland

Roland M-1000 Bruksanvisning

12 Oktober 2024
Roland

Roland KD-200 Bruksanvisning

7 Oktober 2024
Roland

Roland DM-10 Bruksanvisning

5 Oktober 2024
Roland

Roland RD-88 EX Bruksanvisning

26 September 2024
Roland

Roland VR-400UHD Bruksanvisning

25 September 2024
Roland

Roland GO:PODCAST Bruksanvisning

23 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024