Sani-Lav 524 Bruksanvisning

Sani-Lav Sjunka 524

Läs nedan 📖 manual på svenska för Sani-Lav 524 (7 sidor) i kategorin Sjunka. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

H A N D S - F R E E F L O O R M O U N T S I N K

Columbia does not recommend use with harsh chemicals.

Product Compliance

NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Low-Lead

Operating Manual for Hands-Free Floor Mount Stainless Steel Sink

Models 524 and 524-0.5

of Domestic and Foreign Parts

H A N D S - F R E E F L O O R M O U N T S I N K 2

C O L U M B I A S P E C I F I C AT I O N S

800.626.2117 columbiasinks.com info@columbiasinks.com

Installation Instructions

Step 1

1. Attach upper and lower leg support brackets to legs with hardware (provided).

2. Place wash station sink on leg assembly and secure with hardware (provided).

3. Establish sink location.

4. Mark the floor where the four holes are at the base as shown in illustration A.

5. Drill holes as required for mounting hardware. (Hardware not included).

Step 2

1. Install spout assembly to the sink.

2. Install elbow fitting (provided) to the spout assembly.

3. Connect one side of the supply line (provided) to the spout assembly.

4. Install strainer assembly.

Step 3

1. Install elbow fitting to valve.

2. Install foot pedal valves under the leg assembly cross bar if not mounted already.

3. Attach connecting tube from the spout to the foot pedal valve.

Step 4

1. Secure wash station to the floor.

2. Connect waste line to strainer assembly.

3. Connect water supplies (hot and cold) to valves.

Step 5

1. Remove aerator from the spout assembly and flush water line by pressing pedal for

30 seconds.

2. Check connections for leaks. Replace aerator onto the spout assembly.

3. Seal gap between bowl and leg assembly as shown in illustration B.

4. When mounting against wall, we recommend sealing top of backsplash to wall as shown in

illustration C.

Parts List

(1) Floor mount sink

(1) Leg assembly set

(6) Nuts, bolts and washers for leg assembly

(4) Nuts and washers for connecting sink to leg assembly

(1) Double foot pedal valve

(2) Valve mounting nuts

(1) Swivel gooseneck spout with aerator

(1) Connecting tube for valve to spout connection

(2) Fittings, brass, 0.375” male compression and 0.375” male NPT

(1) Strainer assembly with basket

Tools Required

Tape measure

Adjustable wrench

Drill motor and drill bits

Pipe wrench

Level

Safety glasses

Screw drivers: phillips and standard

Pencil

Socket wrench

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Go to for more information on replacement parts and installation videos.columbiasinks.com

Illustration A

Illustration B

Illustration C

H A N D S - F R E E F L O O R M O U N T S I N K 3

C O L U M B I A S P E C I F I C AT I O N S

800.626.2117 columbiasinks.com info@columbiasinks.com

Valve Repair Instructions

Note: Valves are designed to be repaired without having to be disconnected from mount or plumbing.

1. Turn off water source. Do not remove valve from sink.

2. Remove pedal assembly using a 15/16” open end wrench or socket wrench. As shown in

illustration A.

3. Using a 1” deep socket wrench remove insert assembly parts as show in illustration B.

4. Replace with new repair kit as shown on illustration C.

5. Reinstall pedal assembly and turn water source on.

Trouble Shooting Guide

Problem Possible Cause To Diagnose Remedy

Water drips from spout

or valve stem assembly.

Flat washer on the

stem/plunger is worn.

To determine if the leak source is from the hot or cold side shut

cold water source off. See if water still leaks from the spout. If

leak continues then repair hot side if not repair cold side.

We recommend installing valve repair

kit.

Water leaks from the

front of the valve.

O-Rings on the

plunger are worn out.

Visually determine whether the cold or hot side is leaking. We recommend replacing threaded

insert, plunger assembly & spring.

See illustrations below.

Illustration A

Illustration B

Illustration C

Produktspecifikationer

Varumärke:	Sani-Lav
Kategori:	Sjunka
Modell:	524
Färg på produkten:	Zwart
Vikt:	50 g
Bredd:	128 mm
Djup:	128 mm
Höjd:	13 mm
Avsedd för:	Laptop
Internera:	Nee
Värdgränssnitt:	SATA
Utgångsgränssnitt:	USB 2.0