Sani-Lav 5A4F Bruksanvisning
Läs nedan 📖 manual på svenska för Sani-Lav 5A4F (5 sidor) i kategorin Sjunka. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/5
1
W A L L M O U N T S I N K
Operating Manual for Wall Mount Stainless Steel Sink
Models 5A4F and 5A4F-0.5
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 61, Section 9, ASME A112.18.1/CSA B125.1, ADA Compliant
ADA Compliant
Illustration A
Illustration B
Illustration C
2
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
W A L L M O U N T S I N K
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Measure a recommended 45” from finished floor and draw a level line which will be the top edge
of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill holes
and secure bracket to the wall as shown in illustration A. Screws are not provided.
Step 2
1. Install faucet to the sink using faucet mounting kit provided. We recommend using pipe thread
sealant instead of Teflon tape.
2. Install strainer assembly to the drain hole.
3. Connect hot and cold water supply lines (not included) to the back of faucets.
Step 3
1. Position sink onto the wall bracket.
2. Mount support bracket to the bottom of the sink. Do not tighten.
3. Slide or push support brackets against the wall and mark holes for fastening. See illustration B.
4. Remove support brackets from the sink and drill holes for fastening.
5. Install fastening hardware to the drilled holes. (not included)
6. Mount support bracket to the bottom of the sink and fasten them to the wall.
Step 4
1. Install valves onto the sink.
2. Install elbow fittings to Knee Pedal Valves.
3. Connect hot and cold connecting tubes from the spouts to valves.
Step 5
1. Connect waste line or drain pipe to the strainer assembly.
2. Connect hot and cold water supply line to the water source.
Step 6
1. Remove aerator from the spout assembly and flush water system. Check connections for leaks.
Replace aerator onto the spout assembly.
2. We recommend sealing top of backsplash to wall as shown in illustration C.
Parts List
(1) Wall mount sink
(1) 8” on center faucet
(1) Faucet mounting kit
(1) Wall-mounting bracket
(2) Support brackets
(4) Support bracket mounting bolts and washers
(1) Strainer assembly with basket
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from
the spout or from
under the lever.
1. Seat washer is worn
2. Seat is worn
3. O-rings are worn
Shut cold water source off.
See if water still leaks from the
spout. If leaks continues repair
hot side if not repair cold side.
Recommend
installing hot
or cold faucet
repair kit.
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certied under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Go to for more information on replacement parts and installation videos.columbiasinks.com
Wall-mounting bracket
9” (228.6mm)
Front
21” (533.4mm)
7.5”
(191mm)
.875” (22mm)
dia. holes (2)
Hole Configurations
6” (152.4mm)
14”
(355.6mm)
14”
(355.6mm)
8”
(203.2mm)
5” (127mm)
4” (101.6mm)
2” (50.8mm)
.5” R (12.7mm)
22” (558.8mm)
11”
(279.4mm) 11”
(279.4mm)
19”
(482.6mm)
15.5”
(381mm)
1.5” (38mm)
2” (51mm)
Top
19” (482.6mm)
6” (152.4 mm)
1.5” (38mm)
.5” R
(12.7mm) Cross-breaks
to aid drainage
2” drain hole
9” (228.6mm)
45º
7” (177.8mm)
35” (889mm)
suggested
floor to rim
height
Side 19” (482.6mm)
2” (51mm)
1.5” (38mm)
16.75”
(425.5mm)
1.5”
(38.1mm) .875”
(22.22mm)
Back
Splash
.25”
dia. hole
Wall Mounting Detail
Supply Line Detail
Back Splash
1/2” Male NPT
Hot
from Wall
Cold
from Wall
3
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
W A L L M O U N T S I N K
Produktspecifikationer
| Varumärke: | Sani-Lav |
| Kategori: | Sjunka |
| Modell: | 5A4F |
Behöver du hjälp?
Om du behöver hjälp med Sani-Lav 5A4F ställ en fråga nedan och andra användare kommer att svara dig
Sjunka Sani-Lav Manualer
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
10 September 2024
Sjunka Manualer
- Sjunka Smeg
- Sjunka Teka
- Sjunka Hotpoint-Ariston
- Sjunka Kernau
- Sjunka Blaupunkt
- Sjunka Concept
- Sjunka CDA
- Sjunka Hendi
- Sjunka Blanco
- Sjunka Rangemaster
- Sjunka Gustavsberg
- Sjunka Franke
- Sjunka Leisure
- Sjunka Nodor
- Sjunka Elkay
- Sjunka Schock
- Sjunka Caple
- Sjunka Roca
- Sjunka Foster
- Sjunka Advance Tabco
- Sjunka Fulgor Milano
- Sjunka Deante
- Sjunka Artusi
- Sjunka Tot Mate
- Sjunka Atosa
- Sjunka Kuchinox
- Sjunka Oliveri
- Sjunka Shaws
- Sjunka Seima
Nyaste Sjunka Manualer
8 Januari 2025
3 Januari 2025
2 Januari 2025
31 December 2025
31 December 2025
29 December 2024
29 December 2024
29 December 2024
28 December 2024
28 December 2024