Sani-Lav 707B Bruksanvisning

Sani-Lav Sjunka 707B

Läs nedan 📖 manual på svenska för Sani-Lav 707B (9 sidor) i kategorin Sjunka. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/9

A C O R B AT T E R Y P O WERE D

S I N K W I T H E L E C T R O N I C S E N S O R

Operating Manual for Hands-Free Wall Mount Stainless Steel Sink

AC Models 707A and 707A-0.5

Battery Models 707B and 707B-0.5

of Domestic and Foreign Parts

Columbia does not recommend use with harsh chemicals.

Product Compliance

NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Lead-Free Compliant, ASME A112.18.1

COLUMBIA SPECIFICATIONS

A C O R B AT T E R Y P O W E R E D

S I N K W I T H E L E C T R O N I C S E N S O R

800.626.2117 columbiasinks.com info@columbiasinks.com

Installation Instructions

Step 1

1. Establish sink location on the wall.

2. Determine desired height for the top of the backsplash from finished floor and draw a level

line which will be the top edge of the wall mounting bracket.

3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill

holes and secure bracket to the wall as shown in illustration A. Screws are not provided.

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Position the sink onto wall bracket.

2. Loosely attach support brackets under sink and push against wall then mark holes for

drilling as shown in illustration B.

3. Remove support brackets from sink and drill holes for mounting fasteners (not provided).

4. Re-mount support brackets to sink and fasten to wall.

Step 4

1. Connect waste line to strainer assembly (s).

2. Mount sensor control box at desired location on wall.

3. Connect power line from sensor to control box.

4. Attach supply tube from faucet to control box.

5. Connect hot and cold water from the source to mixing check valve (s).

6. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor

installation instructions)

7. Check connections for leaks.

8. Replace aerator onto the spout (s).

9. We recommend sealing top of backsplash to wall as shown in illustration C.

Parts List

(1) Wall mount sink

(1) AC or Battery powered sensor faucet assembly

(1) Wall-mounting bracket

(2) Support brackets

(4) Support bracket mounting bolts and washers

(1) Mixing check valve

(1) Strainer assembly with basket

Tools Required

Tape measure

Adjustable wrench

Drill motor and drill bits

Pipe wrench

Level

Safety glasses

Screw drivers: phillips and standard

Pencil

Socket wrench

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Go to for more information on replacement parts and installation videos.columbiasinks.com

Illustration A

Illustration B

Illustration C

COLUMBIA SPECIFICATIONS

A C O R B AT T E R Y P O W E R E D

S I N K W I T H E L E C T R O N I C S E N S O R

800.626.2117 columbiasinks.com info@columbiasinks.com

10in

254mm

10in

254mm

9.5in

241.3mm

7in

178.9mm

18.828in

478.2mm

20in

508mm

2in

50.8mm

14in

355.6mm

1.5in

38.1mm

1.5in

38.1mm

17in

431.8mm

17.5in

444.5mm

Hole Conﬁguration

.875” [22mm]

dia. hole

10in

254mm

10in

254mm

3.25in

82.6mm

4in

100mm

Front Side

Top

2”

(51mm) .875”

(22.22mm)

Back

Splash

.375”

dia. hole

Wall-mounting

bracket

6.25in

158.8mm

2.5in

63.5mm

15.5in

393.7mm

R.75in

19.1mm

.75in

19.1mm

7.087in

180mm

11in

279.4mm

14”

(355.6mm)

2” drain

hole

6in

152.4mm

R.5in

12.7mm

Wall Mounting Detail

Produktspecifikationer

Varumärke:	Sani-Lav
Kategori:	Sjunka
Modell:	707B
Färg på produkten:	Zwart
Vikt:	77000 g
Bredd:	500 mm
Djup:	586 mm
Höjd:	1207 mm
Sladdlängd:	1.8 m
Förpackningens vikt:	87000 g
Förpackningens bredd:	560 mm
Djuppackning:	640 mm
Förpackningshöjd:	1220 mm
Snäll:	Wagentje voor draagbaar apparaatbeheer
Användarmanual:	Ja
Husmaterial:	Staal
LED-indikatorer:	Bezig met opladen
Nuvarande:	15 A
Placering:	Vloer
Medföljande kablar:	Stroom
Med lås:	Ja
Ursprungsland:	China
Certifiering:	CE
Hållbarhetscertifikat:	CE, REACH, RoHS, UKCA
Justerbara hyllor:	Ja
Förvaringstemperatur:	-40 - 60 °C
Laddningskälla:	USB Type-C
Förvaringsfuktighet:	20 - 90 procent
Handvat(en):	Ja
Bästa användningen:	Kantoor
Montering krävs:	Nee
Förbättrad kabelhantering:	Nee
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 / 60 Hz
Drifttemperatur (TT):	-10 - 40 °C
Relativ luftfuktighet i drift (VV):	20 - 80 procent
Maximal skärmstorlek:	- "
Låsbara hjul:	Ja
Wieldiameter:	127 mm
Bärbara enheter som stöds:	Notebook, Tablet
Slot typ:	Sleutel
Fackets bredd:	34 mm
Spårdjup:	400 mm
Spårhöjd:	278 mm
Inkluderade typer av nätkontakter:	EU, UK
Strömkabelns-längd:	1.83 m
Nycklar ingår:	Ja