Sanwa M53 Bruksanvisning

Läs nedan 📖 manual på svenska för Sanwa M53 (20 sidor) i kategorin Mätutrustning. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/20
M53
DIGITAL INSULATION METER
WITH VOLTAGE & SPEED RANGE
INSTRUCTION MANUAL
− − 1
[1] Safety Precautions
---
Be sure to read before use.
---
Be sure to read carefully the information under WARNING” and
“ CAUTIONin this manual in order to prevent human injuries, electric
shock and damage to the instrument as well as other equipment.
1-1 Warning Markings and Other Symbols
The symbols and their meanings used with the instrument and in this
manual are as described below.
The information under this marking must be
observed strictly to prevent human injuries,
including burns and electric shock.
The handling information under this marking
should be observed carefully to prevent damage
to the instrument and associated equipment.
 Other symbols used with the instrument and in this manual
Indicates a risk of shock due to a high voltage generated
or applied at a measuring terminal.
E
Insulation resistance measurement terminal (Earth=GND)
L Insulation resistance measurement terminal (Line)
ACV AC voltage
DCV DC voltage
M Insulation resistance
V . SPEED Voltage and speed measurement terminal
Voltage polarity DCV:+positive terminal, ACV:~(No polarity)
Voltage polarity DCV:-negative terminal, ACV:~(No polarity)
SPEED m/min
Speed measurement range (DCV 0~20 V range)
INSUL.
TEST VOLT Insulation test voltage ON indication
ON
POWER Measuring power switch
WARNING
CAUTION
− − 2
1-2 Warning Messages for Safety
WARNING
1. Check the measurement type (insulation resistance, DC or AC
voltage) before measurement and select the appropriate
function for it.
2. Do not apply a voltage or signal exceeding the specified
maximum allowable input. (For the maximum allowable input
voltage value, see section 1-3 on the next page.)
3. Do not open the case or battery cover unless replacing the
batteries as described in this manual.
4. Always use the test leads specified in the manual.
5. If the insulation coating of a test lead is damaged or its
conductor wire is exposed, do not attempt to repair it.
Instead, replace with a new test lead.
6. Do not switch the measuring function during measurement.
7. Do not use the instrument when it is moistened, when your
hand is wet or when the ambient humidity is high (85 %RH or
more).
8. Do not touch the metallic parts of the test leads during
measurement.
9. Do not use the instrument if it is defective and incapable of
making the specified measurements.
10. Do not use the instrument using high-power or higher voltage
circuitry than the maximum allowable input.
11. Be sure to conduct annual inspections.

Produktspecifikationer

Varumärke: Sanwa
Kategori: Mätutrustning
Modell: M53

Behöver du hjälp?

Om du behöver hjälp med Sanwa M53 ställ en fråga nedan och andra användare kommer att svara dig




Mätutrustning Sanwa Manualer

Sanwa

Sanwa PDR302 Bruksanvisning

18 September 2024
Sanwa

Sanwa PDR4000 Bruksanvisning

18 September 2024
Sanwa

Sanwa KDP10 Bruksanvisning

18 September 2024
Sanwa

Sanwa SE300 Bruksanvisning

17 September 2024
Sanwa

Sanwa SE9100 Bruksanvisning

17 September 2024
Sanwa

Sanwa LX20 Bruksanvisning

17 September 2024
Sanwa

Sanwa LP10 Bruksanvisning

17 September 2024
Sanwa

Sanwa DCL31DR Bruksanvisning

17 September 2024
Sanwa

Sanwa MG5000 Bruksanvisning

17 September 2024
Sanwa

Sanwa HG561H Bruksanvisning

17 September 2024

Mätutrustning Manualer

Nyaste Mätutrustning Manualer