Schneider MTN6600-0603 Bruksanvisning

Schneider Inte kategoriserad MTN6600-0603

Läs nedan 📖 manual på svenska för Schneider MTN6600-0603 (15 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/15

Energy Meter REG-K/3x230/16 A

Art no. MTN6600-0603

Application Energy metering/saving/calculating 7601/1.0

Table of contents

Function overview

Using this application, you can operate the REG-K/

3x230/16 A energy counter for measuring and monitor-

ing energy. This means you can monitor up to 3 chan-

nels independently of one another. You can send the

data to the KNX bus for evaluation.

You have access both to channel-dependent and chan-

nel-independent functions.

When the application is loaded, the following functions

can be implemented, evaluated and controlled via the

bus:

You can set a separate energy saving and alarm func-

tion with corresponding actions for each channel:

Application Energy metering/saving/cal-

culating 7601/1.0

• Function overview 1

• Behaviour of the application 2

• General functions 2

– Select channels (1-3) 2

– Nominal voltage level 3

– Start delay 3

• Functions per channel 3

– Energy counter 3

– Energy saving function 4

– Alarm function 6

• Data transmission 7

• Tariff counter 8

• Energy calculator 9

• Status 10

– Bus voltage failure counter 10

– Energy counter and total energy counter 10

– Tariff counter 11

• Overview of parameters 12

• Overview of communication objects 15

Channel 1

Channel 2

Channel 3

Energy counter

Energy saving function

Alarm function

Data transmission

Tariff counter

Energy calculator

Status

Energy counter

Energy saving function

Alarm function

Energy counter

Energy saving function

Alarm function

Channel 1-3

Energy saving function Threshold 1-8

Switch object

Dimming object

Value object

Scene object

Temperature object

Alarm function Alarm limits

Alarm object

Energy Meter REG-K/3x230/16 A

Art no. MTN6600-0603

Behaviour of the application

|Many parameters and their settings are depend-

ent on the settings you have already made for oth-

er parameters. This means that some parameters

will appear or disappear and the values available

for selection will change according to settings you

have already made. These dependencies have

not been shown in the table for reasons of clarity.

All settings are always shown.

|Configurable times are set via the base and factor

parameters. The actual time is given by the multi-

plication of the two values. Example:

Base = 1 second, Factor = 3

Actual time = 3 seconds

|The bold values in a table are the values set dur-

ing factory configuration.

The application is influenced by the following events:

• ETS download

• Bus voltage failure

• Bus voltage recovery

The behaviour differs according to function and can in-

fluence the measuring and monitoring function. There-

fore, you can set the behaviour using parameters at the

corresponding point. Refer to the chapter in question

for a precise description.

Select channels

You can enable channels 1-3 separately. On enabled

channels, you can then set additional functions (energy

saving and alarm function) using parameters.

Parameters

Data transmission

You can send the measured current and power values

per channel for evaluation and visualisation to the KNX

bus.

Further settings are possible using parameters on an

enabled function.

Parameters

Tariff counter

You can count the energy separately for up to four tar-

iffs. Using these values, you can then calculate your en-

ergy costs according to the applicable tariff.

Further settings are possible using parameters on an

enabled function.

Parameters

Energy calculator

You can add together the measured current and power

values of several channels and send them for evalua-

tion and visualisation to the KNX bus.

Further settings are possible using parameters on an

enabled function.

Parameters

Behaviour of the application

General functions

Parameters Setting

Channel X Disabled

Enabled

General functions

Parameters Setting

Data transmission Disabled

Enabled

General functions

Parameters Setting

Tariff counter Disabled

Enabled

General functions

Parameters Setting

Energy calculator Disabled

Enabled

Energy Meter REG-K/3x230/16 A

Art no. MTN6600-0603

Functions per channel

Status

You can receive status indications on bus voltage failure

and on exceeding thresholds of the energy meters and

tariff counters.

Further settings are possible using parameters on an

enabled function.

Parameters

Nominal voltage level

The energy counter measures energy pulses on the

connected channels, but not the voltage. Using the

nominal voltage level parameter, you can adapt the de-

vice to your local nominal voltage level. The set value

forms the basis for calculating current magnitude and

power. The more accurately the set value corresponds

to your actual voltage level, the more accurate the cal-

culated values will be.

Parameters

Start delay

The start delay specifies from what point measured val-

ues are counted in the application. After an ETS down-

load or bus voltage recovery, the device starts

measuring the connected channels directly. You can

delay the start of counting to allow the application to re-

ceive external values from the bus, e.g. system time or

external energy values.

Parameters

Energy counter

The application sends the energy values measured by

the device via the 4-byte objects "Energy" and "Total

energy" to the KNX bus. Two energy counters are avail-

able for each connected channel:

• Energy counter: This counter can be reset to 0 as re-

quired using the "Reset" object. This means you can

perform measurements over defined periods. In addi-

tion, you can specify a start value (offset) for the coun-

ter using the "Energy" object.

• Total energy counter: This counter continuously

counts the energy since the device was first commis-

sioned. The counter can only be reset if its counter

threshold is exceeded. This threshold and the behav-

iour on exceeding it can be set in the "Status" tab.

You can select between the energy units Wh and kWh.

This setting applies to both counters jointly.

The energy values can be transmitted actively or pas-

sively. In the "Passive (read only)" setting, the values

are requested via the bus. The values can also be sent

actively, either at cyclical intervals or when the energy

value changes. The cyclic interval and the energy in-

crease can be set using parameters. In the "Cyclically

and if energy was changed" setting, the values are also

sent cyclically. However, the cycle starts again when the

energy increases by the set value.

The energy counter also displays the instantaneous

current using the "Instantaneous current" 2-byte object.

Communication objects

The following communication objects can be selected:

(Per channel)

General functions

Parameters Setting

Status Disabled

Enabled

General functions

Parameters Setting

Nominal voltage level

1 V* factor (210-240)

230

adjustable in single steps

General functions

Parameters Setting

Start delay

1 s * factor (1-240)

adjustable in single steps

Functions per channel

Function Object name Type Prio Flags Behaviour

Channel X

energy

Reset 1 bit Low CW Receive

Channel X

energy

Total energy 4 byte Low CRT Send

Channel X

energy

Energy 4 byte Low CRW

Send/re-

ceive

Channel X

energy

Instantaneous

current

2 byte Low CR Send after

read re-

quest

Produktspecifikationer

Varumärke:	Schneider
Kategori:	Inte kategoriserad
Modell:	MTN6600-0603

Behöver du hjälp?

Om du behöver hjälp med Schneider MTN6600-0603 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Schneider Manualer

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Schneider EVH3S3P0CK Bruksanvisning

10 Oktober 2024

Schneider Wiser CCT593012 Bruksanvisning

26 September 2024

Schneider Wiser CCT592012 Bruksanvisning

26 September 2024

Schneider VW3A7740 Bruksanvisning

25 September 2024

Schneider VW3A7750 Bruksanvisning

25 September 2024

Schneider VW3A7746 Bruksanvisning

25 September 2024

Schneider VW3A7752 Bruksanvisning

25 September 2024

Schneider VW3A7742 Bruksanvisning

25 September 2024

Schneider VW3A7737 Bruksanvisning

25 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024

Hager Vision VKG004A-T Bruksanvisning

27 Oktober 2024