Speco Technologies Intensifier IP OIMD1W Bruksanvisning

Speco Technologies övervakningskamera Intensifier IP OIMD1W

Läs nedan 📖 manual på svenska för Speco Technologies Intensifier IP OIMD1W (29 sidor) i kategorin övervakningskamera. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/29
O
Intensifier IP
®
Fu
Mini
at
2iMT61
ll
HD Megapi
xel Indoor/O
ure
Turret IP Camera
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 2
Caution
Any changes or modifications in construction of this device which are not explicitly approved by the
party responsible for compliance could void the users warranty.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generate, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help.
Directions
Be careful not to cause any physical damage by dropping or throwing the camera. Especially keep the
device out of reach from children.
Do not disassemble the camera. No after service is assumed when disassembled.
Use only power adapters compatible with the unit.
Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when
installing the unit. The screw holes for the installation screws and pipe should be maintained water tight
during the whole life time of the product.
All the electrical connection wires running into the unit should be prepared so that water from the outside
cannot flow into the unit through the surface of the wires. Penetration of the moisture through the wire for
extended period can cause malfunction of the unit or deteriorated image.
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 3
Revision History
Date Revision Details
Feb 25
th
, 2014 1.0 First manual revision creation.
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 4
Contents
1. Introduction .................................................................................................................................................... 5
1.1. Overview ............................................................................................................................................... 5
1.2. Specifications ........................................................................................................................................ 6
1.3. Applications of O2iMT61 ....................................................................................................................... 8
2. Product Description ...................................................................................................................................... 9
2.1. Contents ................................................................................................................................................ 9
2.2. Product Preview .................................................................................................................................... 9
2.3. Physical description ............................................................................................................................ 10
2.3.1. External View ............................................................................................................................ 10
2.3.2. Dimensions ............................................................................................................................... 10
2.3.3. Front and Rear view of Encoder box ........................................................................................ 11
2.3.4. Factory Default Switch .............................................................................................................. 11
2.4. Functional Description ........................................................................................................................ 12
3. On Site Installation ...................................................................................................................................... 14
4. Getting Started ............................................................................................................................................. 16
4.1. PC Requirement ................................................................................................................................. 16
4.2. Quick Installation Guide ...................................................................................................................... 17
4.2.1. Connect PC and O2iMT61 to network. ..................................................................................... 17
4.2.2. Install Speco-NVR and set IP parameters on O2iMT61 ........................................................... 17
4.2.3. Remote video connection to O2iMT61 ..................................................................................... 19
4.2.4. Additional settings through connection to the Admin Page ...................................................... 21
5. Troubleshooting ........................................................................................................................................... 22
5.1. No power is applied ............................................................................................................................ 22
5.2. Cannot connect to the Video ............................................................................................................... 23
5.3. Windows Vista or Windows 7 .............................................................................................................. 24
5.4. Technical Assistance ........................................................................................................................... 27
Appendix A Important Notice in Exchanging SD Card (Micro SD) ......................................................................... 28
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 5
1. Introduction
1.1. Overview
The ONSIP O2iMT61 is a state-of-the-art mega-pixel, dual-codec (H.264, MJPEG) IP/network camera built with
embedded software and hardware technology. It enables real time transmission of synchronized video of Full
HD resolution and audio data. Remote clients can connect to ONSIP O2iMT61 for the real time video/audio
data through various client solutions running on PC, PDA or mobile phones. Real time 2-way communication is
available through bidirectional audio communication feature.
Intensifier IP® technology is the most optimized solution for indoor and outdoor surveillance in low-light
conditions by using superior CMOS sensor with low-light sensitivity ISP sensor. Intensifier IP® is especially
beneficial in poor lighting environments, efficiently reducing noise and ghosting while maintain a color image
without the use of IR LEDs.
Designed to be a stand-alone streaming audio & video transmission device, ONSIP O2iMT61 can be applied to
various application area such as video security, remote video monitoring, distance education, video conference
or internet broadcasting system.
The separate encoder box and camera design allows for smaller camera housing and flexibility in installations.
The camera portion is vandal and weather resistant, which allows it to be installed in outdoor settings, while the
encoder box can be hidden from view. Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the
owner to reduce the total cost of ownership by reducing on-site wiring works for the installation.
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 6
1.2. Specifications
Camera
Image sensor Progressive scan 1/3 inch CMOS 2M pixels
Full resolution 1,920 x 1,080 pixels (Full HD)
Sync System Internal
Lens 2.9mm fixed (3.6mm, 6mm optional)
Day & Night AUTO, DAY, NIGHT
Sensitivity Intensifier Max 0.0005 Lux
Back Light Compensation ON / OFF
White Balance ATW(2.000K ~ 10,000K) / MANUAL / PUSH
Exposure DC / ESC
WDR ON / OFF
3D-DNR 0 ~ 20
Intensifier AUTO ON (Max 128x) / OFF
Privacy Mask ON / OFF (10 Programmable Zones)
Motion Detection ON / OFF (4 Programmable Zones)
Digital Zoom 1x ~ 12x
Mirror H / V / Rotate
DEFOG ON / OFF
OSD BUILT IN
Video
Compression method Simultaneous Dual Codec (H.264 / MJPEG)
Resolution 1,920 x 1,080@30fps
Multi-Profile Streaming - 5 simultaneous video profiles
- Select the codec type, resolution and frame rates for each profile.
Intelligent Bit-Rate Control VBR or CBR
PTZ Digital PTZ & Video crop
Image Setting Text overlay, Privacy mask, De-interlace filter
Motion detection 3 regions
Audio
Mono Upstream 32Kbps G.726 ADPCM, 64Kbps 16bit -law PCM ~ MIC/Line-in µ
Mono Downstream 64Kbps 16bit -law PCM ~ Line-out µ
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 8
1.3. Applications of O2iMT61
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
Weather and environmental observation
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
2. Product Description
2.1. Contents
The product package
contains following
Contents
O2iMT61
O2iMT6
Accessories
Screws
Anchor
L-
type w
Cable b
CD
Softwar
Reference Guide
Quick in
2.2. Product Preview
O2iMT61
Camera Unit &
Main Unit
P
gs :
Description
R
61
main and camera units
s (1 type)
s (1 type)
wrench
bracket
and Screw
re & User’s
Guide
nstallation guide
, Guide pattern
ONSIP Installer VMS Software
PC software to allocate an IP
address to the IP Camera
PC software to view
A/V streaming data
IP camera.
(Simultaneous sup
IP cameras@D1)
emarks
(Speco NVR)
w and
record the
a transmitted from
port of up to 64
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 10
2.3. Physical description
2.3.1. External View
Figure 2-1. External view of O2iMT61
2.3.2. Dimensions
Figure 2-2. Dimensions
Unit : mm
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
2.3.3. Front and Rear view of
Main Un
Figure 2-3. Front view
Figure 2-4. Rear view
2.3.4. Factory Default Switch
Factory default switch is provided for re
There are two functions assigned to fac
1.
Returning to Factory Default St
return to factory default state.
2. Safe Removal of Micro-SD C
ard
removal.
Figure 2-
4. Fact
Micro SD Card
s
nit
Pin
Description
1
Line Output
2 Ground
3 MIC/
Line Inp
4
Relay Outpu
5 Relay
Outpu
6 Sensor Input
7 Sensor Input
(
Connect
Camera
Connect Camera
turning the IP camera to factory default state.
ctory default
switch.
tate
: Press the switch about 5 seconds while power
d
: Press the switch for 1 second to unmount Micro-
S
tory Default switch and Micro
-SD Card slot
Factory Default Switch
lot
Cable bracket screw hole
n
t
ut
ut
ut
(-)
(+)
a
Unit
r is applied to
SD
Card for safe
O
O2
2i
iM
MT
T6
61
1
U
Us
se
er
r
s
s
G
Gu
ui
id
de
e
Rev.1.0 (Feb. 2015) 13
Sensor Input
Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion sensor,
heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to “Sensor Input”.
The sensor type (NC/NO) can be set in admin page. Multiple sensor devices can be connected in parallel.
Figure 2-6. SENSOR input and connection of the sensor
Relay Output
Relay output is provided for connecting alarm devices or for remote on/off control of devices such as light.
Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay is capable
of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit, use
additional relay switch as shown in the right of Figure.
* Left : switching requirement below 30V, 2A
* Right : switching requirement higher than 30V, 2A. Apply this connection when either voltage or
current exceed the limit.
Figure 2-7. RELAY Output connection
Alarm
Out
Device
Power
Supply
( ~30V)
( ~ 2A)
(DC/AC)
Alarm
Out
Device
Power
Supply
(30V~ )
( 2A~ )
(DC/AC)
Optional
Relay
Switch
Power
Supply
( ~30V)
( ~ 2A)
(DC/AC)
Relay
Relay
Photo Coupler NO/NC Type Open Collector Type
Sensor1+
Sensor
Device
Sensor1-
Sensor
Device
Sensor
Power
Supply
Sensor
Power
Supply
GND
+12V

Produktspecifikationer

Varumärke: Speco Technologies
Kategori: övervakningskamera
Modell: Intensifier IP OIMD1W

Behöver du hjälp?

Om du behöver hjälp med Speco Technologies Intensifier IP OIMD1W ställ en fråga nedan och andra användare kommer att svara dig




övervakningskamera Speco Technologies Manualer

övervakningskamera Manualer

Nyaste övervakningskamera Manualer