Spektrum DX2E Active Bruksanvisning

Spektrum Radiostyrda leksaker DX2E Active

Läs nedan 📖 manual på svenska för Spektrum DX2E Active (7 sidor) i kategorin Radiostyrda leksaker. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

SPEKTRUM DX2E ACTIVE USER GUIDE

The following terms are used throughout the product literature to indicate various levels of potential harm

when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a

little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND

a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral

damage, and serious injury OR create a high probability of superﬁ cial injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

MEANING OF SPECIAL LANGUAGE

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product

before operating. Failure to operate the product correctly can result in damage to the product, personal

property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires

some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result

in injury or damage to the product or other property. This product is not intended for use by children without

direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product

in any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation

and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to

assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always purchase from a Horizon Hobby, LLC

authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all

support and warranty with regards, but not limited to, compatibility and performance of counterfeit products

or products claiming compatibility with DSM or Spektrum technology.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and

aircraft. Horizon Hobby disclaims all liability outside of the intended purpose and will not provide warranty

service related thereto.

Warranty Registration

Visit www.spektrumrc.com/registration today to register your product.

Age Recommendation: Not for children under 14 years. This is not a toy.

SAFETY PRECAUTIONS

• Always ensure all batteries have been properly charged

prior to using the model.

• Always check all servos and their connections prior to each run.

• Never operate your model near spectators, parking areas

or any other area that could result in injury to people or

damage of property.

• Never operate your model during adverse weather

conditions. Poor visibility can cause disorientation and loss

of control of your model.

• Never point the transmitter antenna directly toward the

model. The radiation pattern from the tip of the antenna is

inherently low.

• If at any time during the operation of your model you

observe any erratic or abnormal operation, immediately

stop operation of your model until the cause of the

problem has been ascertained and corrected.

INSTALLING THE BATTERIES

CAUTION: Risk of explosion if battery is replaced

by an incorrect type. Dispose of used batteries

according to national regulations.

CAUTION: If using rechargeable batteries, charge

only rechargeable batteries. Charging non-

rechargeable batteries may cause the batteries to burst,

resulting in injury to persons and/or damage to property.

2 SPEKTRUM DX2E ACTIVE USER GUIDE

Throttle Port

Steering Port

Bind Plug

Antenna

Bind Button

RECEIVER COMPATIBILITY

The DX2E is compatible with all Spektrum

™ DSMR® and

DSM2® receivers.

RECEIVER CONNECTION AND IN-

STALLATION

FAILSAFE

Failsafe positions are also set during binding. In the unlikely

event that the radio link is lost during use, the receiver will

drive the servos to their preprogrammed failsafe positions

(normally full brakes and straight steering). If the receiver

is turned on prior to turning on the transmitter, the receiver

will enter failsafe mode. When the transmitter is turned on,

normal control is resumed. For more information on setting

the failsafe, refer to the Binding a Receiver section above.

Receiver

Steering Servo

Throttle Servo

Battery

Battery To Motor

Electronic

Speed Control

Steering Servo

Receiver

TYPICAL ELECTRIC INSTALLATION

Install the Receiver in your vehicle using double-sided foam

servo tape. Foam servo tape will hold the receiver in place

and help isolate it from vibrations. Mount the antenna up

and away from the vehicle in an antenna tube. The higher up

the antenna is, the better signal it will receive.

CAUTION: Do not cut the antenna.

TYPICAL GAS INSTALLATION

BINDING A RECEIVER

Binding is the process of programming the receiver to

recognize the GUID (Globally Unique Identifier) code of a

single specific transmitter. When a receiver is bound to a

transmitter, the receiver will only respond to that specific

transmitter. The DX2E and SR310 are bound at the factory,

but if you need to rebind for any reason, please follow these

steps:

1. With the receiver off, insert the bind plug into the BIND

port on the receiver.

2. Power the receiver through any other port. The green

LED will flash continuously, indicating the receiver is in

bind mode.

3. With the steering wheel and throttle trigger in the desired

preset failsafe positions (see the Failsafe section on this

page for more information), press and hold the bind

button and turn on the transmitter. The green LED on the

front of the transmitter will flash within three seconds,

indicating the transmitter is in bind mode. Release the

bind button when the green LED flashes. Continue to

hold the failsafe positions until the binding process is

complete.

4. The LED on the receiver will glow solid when the

transmitter and receiver are bound.

5. Remove the bind plug and store it in a convenient place.

You must rebind when:

• Different failsafe positions are desired e.g., when throttle

or steering reversing has been changed.

• Changing receiver types e.g., changing from a DSM2

receiver to DSMR receiver.

• Binding the receiver to a different transmitter.

Solid Green Battery is good (Above 4V)

Flashing Green Battery voltage is critically low.

Replace batteries (below 4V)

BATTERY LED MONITOR

SPEKTRUM DX2E ACTIVE USER GUIDE

Steering Trim Dial

Throttle Trim Dial

Steering

Rate Dial

SERVO REVERSING

If a right steering command does not result in the wheels

turning right (and vice versa), the channel may need to be

reversed. To reverse a channel, switch the position of the

correlating switch—“N” is for normal, “R” is for reverse.

THROTTLE LIMITER

The Throttle Limiter switch limits the throttle ouput from

50/70/100%.This is useful for limiting motor ouput on slick or

loose traction tracks or to limit vehicle speeds for new drivers.

3-POSITION SWITCH

The 3-Position Switch is used to control a third channel and

is factory preset at -100%/Neutral/100%.

STEERING TRIM

The steering trim dial is used to adjust the steering trim

when the wheel is centered. Rotating the dial changes the

steering trim (the steering at rest position). Normally, the

steering trim is adjusted until the vehicle tracks straight.

THROTTLE TRIM

The throttle trim dial is used to adjust the throttle trim

when the throttle stick is released (neutral position). This is

typically used to adjust the brakes. Rotating the dial causes

the throttle trim (the throttle position at rest) to be changed.

CHANGING THE TRAVEL ADJUST

SETTINGS

The travel function supports precise endpoint adjustments in

each direction for the steering and throttle channels.

1. Hold the trigger in the full brake position and the steering wheel

in full right position while powering on the transmitter. The LED

flashes rapidly, indicating the programming mode is active.

2. Throttle End Point: Hold the trigger in the full throttle position.

Turn the TH TRIM knob to adjust the full throttle end point.

3. Brake End Point: Hold the trigger in the full brake position.

Turn the TH TRIM knob to adjust the full brake end point.

Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left

position. Turn the ST TRIM knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full

right position. Turn the ST TRIM knob to adjust the right end

point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings.

The minimum Travel is 75%, and the Maximum travel is

150%. The default travel settings are 125% steering and

100% throttle.

IMPORTANT: If the travel is changed on the DX2E, you must

rebind and calibrate AVC

® Receivers.

STEERING RATE AND GAIN CONTROL

Steering rate (also known as dual rate) allows on-the-fly

steering travel adjustments to be made using the ST Rate

dial. Steering rate limits the amount of travel of the steering

servo. The steering rate cannot be greater than 100%.

When the DX2E is bound to a DSMR® AVC® receiver, the

ST RATE knob controls the sensor gain value. Turn the knob

counterclockwise to reduce the gain or clockwise to increase

the gain.

Reverse Switch

Steering

Reverse Switch

Throttle

Throttle limiter Switch

3 position Switch

Produktspecifikationer

Varumärke:	Spektrum
Kategori:	Radiostyrda leksaker
Modell:	DX2E Active
Färg på produkten:	Grijs
Vikt:	3100 g
Bredd:	390 mm
Djup:	220 mm
Höjd:	43 mm
Husmaterial:	Metaal
LED-indikatorer:	Activity, Link, PoE, Power, Speed
Nuvarande:	8 - 4 A
Strömförbrukning (max):	578.8 W
Nätverksstandard:	IEEE 802.3, IEEE 802.3af, IEEE 802.3at, IEEE 802.3az, IEEE 802.3bt, IEEE 802.3i, IEEE 802.3p, IEEE 802.3u
Förvaringstemperatur:	-20 - 70 °C
Antal fans:	2 ventilator(en)
Rackmontering:	Ja
Medeltid mellan fel (MTBF):	809853.3 uur
Höjd, drift:	0 - 3000 m
Strömförsörjning ingår:	Ja
Quality of Service (QoS):	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Ja
Växlingskapacitet:	48 Gbit/s
MAC-ställbar:	8000 entries
10G-stöd:	Nee
Växlingstyp:	Unmanaged
Antal grundläggande switchande RJ-45 Ethernet-portar:	24
Typ grundläggande switchande RJ-45 Ethernet-portar:	Gigabit Ethernet (10/100/1000)
Paketbuffertminne:	0.192 MB
Latentie (1 Gbps):	12 µs
Full duplex:	Ja
Värmeavledning:	1976.0232 BTU/h
AC-ingångsspänning:	100 - 240 V
AC-ingångsfrekvens:	50/60 Hz
Drifttemperatur (TT):	0 - 50 °C
Relativ luftfuktighet i drift (VV):	10 - 90 procent
Harmoniserad systemkod (HS):	85176990
Total Power over Ethernet (PoE) budget:	480 W
Antal Power over Ethernet plus (PoE+)-portar:	24
Ström per port Power over Ethernet (PoE):	60 W
Paketöverföringshastighet (1 Gbps):	1448000 pps
Halv duplex:	Ja
Typ Power over Ethernet (PoE) stöds:	PoE+