Sun Joe 24V-X2-TLR14-CT Bruksanvisning

Sun Joe Inte kategoriserad 24V-X2-TLR14-CT

Läs nedan 📖 manual på svenska för Sun Joe 24V-X2-TLR14-CT (60 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/60

®, LLC

A Division of Snow Joe

®, LLC

OPERATOR’S MANUAL

CORDLESS TILLER + CULTIVATOR –

TOOL ONLY

48V MAX* | 14-INCH

Model 24V-X2-TLR14-CT Form No. SJ-24V-X2-TLR14-CT-880E-MR2

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

Always follow these safety guidelines. Failure to do so may

result in serious bodily injury or death.

General Safety WARNINGS!

Before using this cordless tool, carefully read and observe the

safety rules and instructions listed below. Before starting work,

make sure that you know how to stop the machine in case of

an emergency. The incorrect use of this machine could cause

serious injury. Keep these instructions in a safe place and on

hand so that they can be consulted when required.

Notice the personal safety alert symbol m used in this

manual to draw your attention to a WARNING given along

with the particular operating instruction. This means that

the operation requires special ATTENTION, CAUTION, and

AWARENESS.

1. Keep work area clean and well-lit – Cluttered, dark

areas invite accidents.

2. Replacement parts – When servicing this unit, use only

identical replacement parts. Replace or repair damaged

parts immediately.

3. Keep children, bystanders, and pets away – All

spectators, including pets, should be kept a safe distance

away from the work area.

4. Know your product – Know how to start and stop the

machine. Be thoroughly familiar with the controls.

5. Use the right tool – Do not use this machine for any job

except that for which it was intended.

6. Dress properly – Do not wear loose clothing or jewelry as

such articles can become caught in moving parts. Wear

a protective covering to contain long hair. Wearing rubber

gloves and substantial non-slip footwear is recommended

when working outdoors.

7. Avoid accidental starting – Do not carry the garden tiller

+ cultivator with your nger on the switch.

mCAUTION! Moving parts will continue to run for several

seconds after turning o the machine.

8. Moving parts – Keep hands and feet away from moving

parts. Keep guards in place and in proper working order.

9. Do not force the tool – It will perform better with less

likelihood of personal or mechanical injury if it is used at

the rate for which it was designed.

10. Do not overreach – Keep proper footing and balance at

all times.

If the tiller + cultivator strikes a foreign object, follow these

steps:

• Stop the cordless tiller + cultivator.

• Inspect for damage.

• Repair any damage before restarting and

operating the tool.

11. Use safety glasses – Also use safety footwear,

snug-tting clothing, protective gloves, hearing, and

head protection.

12. Remove the batteries – Remove the batteries from the

tiller + cultivator when it is not in use, before servicing it,

when changing accessories, and when performing any

other maintenance task.

13. Store idle tool indoors – When not in use, the tiller +

cultivator should be stored indoors in a dry and high or

locked-up place out of the reach of children.

14. Maintain the tiller + cultivator with care – Keep the

cutting edges sharp and clean for optimal performance

and to reduce the risk of injury. Keep the handles dry,

clean, and free from oil and grease. Follow the additional

recommendations described in the maintenance section

of this manual.

15. Avoid dangerous environments – Do not use the tiller

+ cultivator in rain or in damp or wet locations. Do not

operate the tiller + cultivator in gaseous or explosive

atmospheres or use the tiller + cultivator near ammable

or combustible liquids. Motors in these tools normally

spark, and the sparks might ignite fumes.

16. Stay alert – Watch what you are doing. Use common

sense. Do not operate the tiller + cultivator when you

are tired or under the inuence of drugs, alcohol, or

other medication.

17. Check for damaged parts – Before further use of the

appliance, a guard or other part that is damaged should be

carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other condition that may aect its

operation. A guard or other part that is damaged should

be properly repaired or replaced. Contact the Snow Joe®

+ Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563) for assistance.

Training

• Read, understand, and follow all instructions on the tiller

+ cultivator and in the manual before operating this unit.

Thoroughly familiarize yourself with the controls and the

proper use of the equipment. Know how to stop the unit

and disengage the controls quickly.

• Children should never be allowed access to the equipment.

Adults should never operate the equipment without

carefully reading and understanding these instructions.

• Keep the area of operation clear of all persons, particularly

small children or pets.

• Exercise caution to avoid slipping or falling.

• Always plan your cultivating path to avoid discharge of

material toward people, pets, and property (e.g. windows,

cars, etc.). Thrown objects can cause serious personal

injury and property damage. Do not allow anyone in front of

a running machine.

• Keep people, pets, and property at least 25 feet from the

tiller + cultivator while it is in operation. Stop the tiller +

cultivator if people or pets enter the discharge area.

• Always observe the surface conditions in order to avoid

slipping, falling, and unexpected objects.

Preparation

• Always inspect the area where the tiller + cultivator is to

be used. Remove all objects (i.e. stones, sticks, wires, and

other foreign materials) that could be thrown by the blades

or cause the operator to trip.

• Thrown objects can cause serious injury to the eyes and

exposed body. Always wear safety glasses or eye shields

during operation and while making an adjustment or repair.

• Always operate the tiller + cultivator wearing adequate

garments. Do not wear jewelry or other loose clothing,

which could become entangled in moving parts. Wear

non-slip footwear to ensure proper footing.

• Observe any noise-prevention regulations and laws.

• Inspect the tiller + cultivator for worn, missing, or damaged

parts and safety labels. See maintenance section for

detailed instructions.

Operation

• Do not operate the machine while under the inuence of

alcohol or drugs.

• Keep all safety devices in place and in proper working

order. Do not operate with missing or damaged

components.

• Ensure the controls (start/stop) function properly

before cultivating.

• Hold onto the tiller + cultivator with both hands during

operation. Ensure the grips are dry.

• Contact with rotating parts can amputate hands and feet.

Keep hands and feet away from all rotating parts.

• Only operate the tiller + cultivator when there is good

visibility or light and dry conditions. Always watch your

footing and keep a rm hold on the grips. Walk; don't run!

• Do not operate the tiller + cultivator on slippery surfaces.

Check your footing during use.

• Exercise caution when changing direction and operating

the tool on slopes. Always keep feet and legs a safe

distance away from the machine. Look for hidden obstacles

or hazards.

• Do not overload machine capacity by attempting to

cultivate too deeply. It will cause excessive resistance.

• Stop the tiller + cultivator and remove the batteries before

leaving the operating position (behind the handles) to adjust

or inspect the unit. Wait until the blades have come to a

complete stop.

• If the tiller + cultivator should start to vibrate abnormally,

stop the machine and inspect thoroughly for damage.

• Turn the machine OFF when moving to a new work area.

Allow the blades to completely stop rotating before

transporting the unit.

• Always use proper care and good judgment when you

are confronted with a situation that is not covered in

this manual. If you are unsure of what to do, contact

your authorized Snow Joe® + Sun Joe® dealer or call

the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

• Do not use in rain or wet conditions.

• Do not grasp the exposed cutting blades or cutting edges

when picking up or holding the appliance.

Stopping Work

• Always turn the tiller + cultivator OFF and remove the

batteries when stopping work or when changing work

areas. Never leave the machine running when unattended.

• The blades will continue to rotate for a short period after

turning OFF the tiller + cultivator. Wait until the blades

have completely stopped before lifting the machine or

conducting inspection and maintenance.

• The motor housing remains hot for a short period after

the machine is turned OFF. Allow the motor housing to

cool completely before touching or storing near

combustible material.

Maintenance + Storage

• Maintain or replace safety and instruction labels.

• Disengage all controls, stop the engine, and wait until the

blades come to a complete stop before cleaning, repairing,

or inspecting the tiller + cultivator.

• Regularly check the following:

i) Blades are clear and can rotate freely – Accumulation

of debris around the blades could impair performance

or damage the motor. Inspect and clean the area around

the blades before every use.

ii) Safety devices are operating properly – Do not

tamper with or adjust safety devices.

iii) Bolts and screws are properly tightened – Visually

inspect the machine for any damage and ensure that

the tiller + cultivator is in safe working condition.

iv) Use only identical replacement parts – Always replace

damaged parts with original equipment manufacturer’s

(OEM) parts only. Replacement parts that do not meet

the original equipment specications may lead to

improper performance and compromise safety.

Electric Safety

mWARNING! Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in

electric shock, re and/or serious injury.

1. Prevent unintentional starting. Ensure the switch is in the

o-position before connecting with battery packs, picking

up or carrying the appliance. Carrying the appliance with

your nger on the switch or energizing appliance that have

the switch on invites accidents.

2. Remove the battery packs from the appliance before

making any adjustments, changing accessories, or storing

appliance. Such preventive safety measures reduce the

risk of starting the appliance accidentally.

3. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

4. Use appliances only with specically designated battery

packs. Use of any other battery packs may create a risk of

injury and re.

5. When battery packs are not in use, keep them away from

other metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a re.

7. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

8. Do not use a battery pack or appliance that is damaged

or modied. Damaged or modied batteries may exhibit

unpredictable behavior resulting in re, explosion or risk of

injury.

9. Do not expose a battery pack or appliance to re or

excessive temperature. Exposure to re or temperature

above 265°F (130°C) may cause explosion.

10. Follow all charging instructions and do not charge the

battery packs or appliance outside of the temperature

range specied in the instructions. Charging improperly

or at temperatures outside of the specied range may

damage the batteries and increase the risk of re.

11. Have servicing performed by a qualied repair person

using only identical replacement parts. This will ensure

that the safety of the product is maintained.

12. Do not modify or attempt to repair the appliance or the

battery packs (as applicable) except as indicated in the

instructions for use and care.

Battery + Charger

Safety Instructions

NOTE: This unit is tool only. The batteries and the charger are

not included. They must be purchased separately.

Model 24V-X2-TLR14-CT is compatible with the 24V iON+

System batteries and chargers. See page 16 for more

information.

We pay a great deal of attention to the design of every battery

pack to ensure that we supply you with batteries that are safe,

durable and have a high energy density. The battery cells have

a wide range of safety devices. Each individual cell is initially

formatted and its electrical characteristic curves are recorded.

This data is then used exclusively to be able to assemble the

best possible battery packs.

Despite all the safety precautions, caution must always be

exercised when handling batteries. The following points must

be obeyed at all times to ensure safe use. Safe use can only

be guaranteed if undamaged cells are used. Incorrect handling

of the battery packs can cause cell damage.

IMPORTANT! Analyses conrm that incorrect use and poor

care of high-performance batteries are the main factors

responsible for personal and/or product damage.

mWARNING! Use only approved replacement

batteries; other batteries may damage the cordless tiller +

cultivator and cause it to malfunction, which can lead to

serious personal injury.

Produktspecifikationer

Varumärke:	Sun Joe
Kategori:	Inte kategoriserad
Modell:	24V-X2-TLR14-CT

Behöver du hjälp?

Om du behöver hjälp med Sun Joe 24V-X2-TLR14-CT ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Sun Joe Manualer

Sun Joe 24V-BBQ-CT Bruksanvisning

18 September 2024

Sun Joe BDL-A0075 Bruksanvisning

12 September 2024

Sun Joe SJ-SHLV06 Bruksanvisning

12 September 2024

Sun Joe SJ-SHLV07 Bruksanvisning

12 September 2024

Sun Joe TJW24C-RM Bruksanvisning

3 September 2024

Sun Joe 24V-AJC-LTW-PRP-RM Bruksanvisning

30 Augusti 2024

Sun Joe 24V-X2-TLR14-CT Bruksanvisning

28 Augusti 2024

Sun Joe PJ3600C-RM Bruksanvisning

26 Augusti 2024

Sun Joe 24V-X2-DTS15-CT Bruksanvisning

13 Augusti 2024

Sun Joe 24V-X2-TLR14-CT-RM Bruksanvisning

11 Augusti 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024