Swann vPRO-650 Bruksanvisning

Swann övervakningskamera vPRO-650

Läs nedan 📖 manual på svenska för Swann vPRO-650 (40 sidor) i kategorin övervakningskamera. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/40

Operating Instructions

PRO-650™

™

Advanced security made easy

Pan Tilt Zoom

Dome Camera

222

FCC Veriﬁcation:

NOTE: This equipment has been tested and found to comply with the limits for

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to cor-

rect the interference by one or more of the following measures:

· Reorient or relocate the receiving antenna

· Increase the separation between the equipment and the receiver

· Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

· Consult the dealer or an experienced radio/TV technician for help

IMPORTANT NOTE: Prohibition against eavesdropping

Except for the operations of law enforcement ofﬁcers conducted under lawful

authority, no person shall use, either directly or indirectly, a device operated pursu-

ant to the provisions of this Part for the purpose of overhearing or recording the

private conversations of others unless such use is authorized by all of the parties

engaging in the conversation.

WARNING: Modiﬁcations not approved by the party responsible for compliance

could void user’s authority to operate the equipment.

IMPORTANT SAFETY INSTRUCTIONS:

· Make sure product is ﬁxed correctly and stable if fastened in place

· Do not operate if wires and terminals are exposed

FOR BEST RESULTS:

This is a semi-professional 360º PTZ dome camera, conforming to PELCO P/D stand-

ards. To obtain the best image quality, please use a high quality cable, particularly if

the cables required length exceeds 100ft/35m. For the highest video quality, use a

cable with a solid copper inner conductor and shielded with copper braid.

Before you Begin 2

Table of Contents 3

Quick Reference 3

Overview 4

Package Contents 4

Layout of the Camera and PTZ Controller 5

Layout of Remote Control 6

Connecting the Camera 8

Mounting the Camera 10

Setting the Command Address 12

Conﬁguring the PTZ Controller 12

Connecting Multiple PTZ Systems 13

Operating the Camera 14

Advanced Operation 16

Additional Functions 17

Troubleshooting Guide 18

Technical Speciﬁcations 19

Warranty / Technical Support Rear Cover

PRO-650 4” Pan, Tilt, Zoom Dome

Default PTZ Conﬁguration

Default Command Address: 1

Protocol: Pelco-D

Baud Rate: 2400bps

RS485 Polarity:

+A Purple Wire

- B White Wire

888

After running the camera cable through the mounting arm/bracket, 1.

attach to the main plug on the camera circuit board (see opposite).

Connect the BNC connector and power connectors to an extension 2.

cable.

Connect the purple and white wires to the RS485 plug, and insert 3.

the RS485 plug into the RS485 port on the rear of the controller (see

opposite).

Attach the BNC plug on the end of the extension cable to a BNC input 4.

on your TV, VCR or DVR (as applicable). If your monitor/recorder does

not have a BNC connection, then use a BNC to RCA adaptor.

Connect the power connector on the end of the extension cable to 5.

the DC plug of a power adaptor (DC 12V).

Attach the power connector on the rear of the PTZ controller to a 6.

power supply (DC 12V).

Plug the DC 12V power adaptors into mains power.7.

1. Connecting the Camera Cable

Before mounting the camera, it is

important to connect it correctly.

Run the cable through the mounting 1.

arm or bracket you would like to

use.

Make sure you run the cable 2.

through starting with the camera

end (not the end with the BNC

connectors - they’re too big to ﬁt).

Once the cable has been pulled 3.

through, plug it into the top of the

camera.

If you’re planning to mount the 4.

dome outside, cover the screw

threads with a silicon sealant before

screwing the unit together. Failing

to do so will compromise the

waterprooﬁng of the dome.

Then, screw the mounting arm/5.

bracket onto the dome.

Be careful not to damage the connectors

on the end of the cable or to the camera,

particularly when unplugging the

camera, as the connectors are fragile!

3. Connecting the RS485 Cables

Remove the RS485 plug from the back of 1.

the PTZ controller.

Insert the WHITE wire into the -B side of 2.

the RS485 plug, and screw into place.

Insert the PURPLE wire into the +A side of 3.

the RS485 plug, and screw into place.

Plug the RS485 plug into the RS485 port 4.

on the back of the PTZ controller.

Note: If you need a longer cable to reach

the location you’d like to put the PTZ

controller, the RS485 cable can be extended.

If you are unfamiliar with cable construction

and maintenance, we suggest getting a

professional to do this.

Connecting multiple PTZ systems to the included controller is a convenient way to

be able to access and control a complex, multi-camera system from one central

location. This is, however, and advanced feature of PTZ systems, and should

only be attempted by those experienced with security system and/or networking

technologies. In a nutshell: multiple systems can be connected to the RS485 cable

in a bus or line conﬁguration. The exact details of the wiring solution will vary by

environment - the following is presented only as a guide.

Please Note: If you already have, or are planning on getting, a PTZ capable Swann

DVR, then using the supplied PTZ controller is optional. The PTZ system can be

controlled by the RS485 connection built into the DVR.

In the above example, three PTZ domes have been connected to the one central

controller. To achieve this wiring arrangement:

Connect the PTZ systems one at a time, and follow the instructions opposite •

to assign each camera a separate command address.

Multiple cameras sharing a command address can cause problems when •

implementing a system. In the best case scenario, two or more PTZ systems

sharing a command address will move synchronously, without the option to

move each camera separately. Often, a shared command address will prevent

the system from operating normally.

Once each camera has a command address deﬁned, they can be connected •

simultaneously.

Take the purple (+) wires, and connect all three to the +A side of the RS485 plug.•

Repeat for white (-) wires, and connect all three to the -B side of the RS 485 plug.•

Connect the RS485 plug to the PTZ controller.•

Diagram showing a potential wiring

solution for integrating multiple PTZ

systems to the one controller.

161616

The numerical command functions shown in this section are recommended

only for advanced users. Improper use of these commands may interfere

with the functionality of the PTZ system.

The PRO-650 PTZ dome can accept many additional commands to those already

listed. As there are not enough buttons on the remote control to assign one to

each function or setting applicable to the dome, they are presented and used as a

series of numerical commands.

To execute an advanced numerical command function:

Press the PRESET, CLEAR or GOTO button (as applicable) on the remote control.•

As all numerical commands are more than a single digit, press the -/-- button.•

Enter the applicable numerical code for the function you wish to execute. •

Press ENTER to conﬁrm and execute the function.•

PRESET Function

62 Set Left limited point

63 Set Right limited point

76 Set Home Point

77 Set Home Point Wait Time to 64 seconds

78 Set Home Point Wait Time to 128 seconds

79 Set Home Point Wait Time to 192 seconds

80 Set Home Point Wait Time to 255 seconds

81 Enable Auto-Home function

82 Disable Auto-Home function

224 Input number 0

225 Input number 1

226 Input number 2

227 Input number 3

228 Input number 4

229 Input number 5

230 Input number 6

231 Input number 7

232 Input number 8

233 Input number 9

234 Input number 10

235 Input number 11

236 Input number 12

237 Input number 13

238 Input number 14

239 Input number 15

240 Init EEPROM to Default

241 Init System

242 Begin PATTERN setup

243 End PATTERN setup

244 Set PATTERN speed

245 Set PATTERN stay time

246 Set PATTERN point number

247 Start run PATTERN, Enable Auto Start PATTERN cruise

248 Stop run PATTERN, Disable Auto Come Back Home Point

249 Set Pan Limited to 0x38

255 Set Pan/Tilt speed to fast mode

CLEAR Function

1 -- 32 Clear Preset Point

62 Clear Left Limited Point

63 Clear Right Limited Point

76 Clear Home Point

81 Disable Auto Come Back Home Point

92 Clear Left Limited Point

93 Clear Right Limited Point;

240 Init Pan Tilt to Default

249 Set Pan Limited to 0x3F

GOTO Function

1 -- 32 Goto Preset Point

34 Goto Pan Zero point

62 Goto Left Limited Point

63 Goto Right Limited Point

76 Goto Home Point

92 Goto Left Limited Point

93 Goto Right Limited Point

96 Stop Auto Scan

99 Start Auto Scan

Avant de commencer 2

Table des matières 3

Guide de référence rapide 3

Vue d’ensemble 4

Contenu de l’emballage 4

Présentation de la caméra et du contrôleur PTZ 5

Présentation de la télécommande 6

Connecter la caméra 8

Fixation de la caméra 10

Paramétrage de l’adresse de commande 12

Conﬁ guration du contrôleur PTZ 12

Connexion de plusieurs systèmes PTZ 13

Fonctionnement de la caméra 14

Fonctionnement avancé 16

Fonctionnement supplémentaires 17

Guide de résolution des problèmes 18

Spéciﬁ cations techniques 19

Garantie / Support technique 20

Dôme Pan, Tilt & Zoom PRO-650

Conﬁ guration PTZ par défaut

Adresse de commande par défaut : 1

Protocole : Pelco-D

Taux de transfert 2400bps

Polarité RS 485 :

+A Câble violet

- B Câble blanc

1. Kit de montage mur

Pour installer le dôme PRO-650 à un mur ou à une surface verticale.

2. Kit d’installation plafond.

Pour installer le système PRO-650 sur un plafond.

3. Emballage caméra

Contient la caméra, l’unité PTZ et les éléments électriques et électroniques associés.

4. Couverture dôme

Protège la caméra.

e mu

5. Afﬁ chage LED.

Afﬁ che le statut de contrôleur PTZ.

6. 12V DC

Branchez l’adaptateur fourni sur cette prise.

7. Port RS485

Branchez ici la prise RS485

8. Prise RS485

Branchez l’extrémité des contrôles violet et blanc dans cette prise à l’aide des vis fournies

aﬁ n de ﬁ xer les câbles en place. Le câble VIOLET est le « + », la câble BLANC est le « - ».

Vue arrièreVue de face

666

DISP (afﬁ chage) :

Fait basculer l’afﬁ chage à l’avant du contrôleur PTZ,

montrant l’adresse de commande, le protocole et le taux

de transfert.

PRESET (Maintenir appuyé pour déﬁ nir)

Permet de déﬁ nir ou modiﬁ er les paramètres préenregistrés.

PATTERN (Maintenez appuyé)

Permet de programmer une liste de paramètres prédéﬁ nis.

Vous pouvez créer des points que la caméra surveillera

selon une séquence.

SUPPRIMER (Maintenez appuyé)

Supprimera un point prédéﬁ ni.

ACTIVER

Commande au système de lancer l’exécution du

programme prédéﬁ ni.

ACCUEIL, A & B

Points prédéﬁ nis principaux. Ces derniers sont

déﬁ nis de la même manière que les autres points.

(voir page 14) Ils servent ensuite de raccourcis.

0 – 9

0-9 Boutons utilisés pour entrer une valeur numérique

dans le contrôleur PTZ.

Clear/Effacer Permet d’effacer le dernier chiffre saisi

dans le contrôleur, comme le bouton ‘correction’ d’un

clavier d’ordinateur.

-/--

Permet de saisir plus d’un chiffre à la fois. “-” représente

un seul chiffre, tandis que “--” indique un espace

permettant de saisir deux chiffres.

S1 ~ S4

Raccourci permettant de régler

paramètres de VITESSE de la caméra

représente la vitesse la moins importa

4 la plus élevée.

P1 ~ P8

Raccourcis des POSITIONS DE PRES

En appuyant sur ce bouton, la caméra

directement dans une direction prédéﬁ

Produktspecifikationer

Varumärke:	Swann
Kategori:	övervakningskamera
Modell:	vPRO-650

Behöver du hjälp?

Om du behöver hjälp med Swann vPRO-650 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

övervakningskamera Swann Manualer

Swann SWNHD-866MSD Bruksanvisning

3 Oktober 2024

Swann Pro DVR8-4000 Bruksanvisning

16 September 2024

Swann SW312-HMD-CA Bruksanvisning

16 September 2024

Swann PRO-A851 Bruksanvisning

15 September 2024

Swann DVR4-1000 Bruksanvisning

9 September 2024

Swann PRO-760 Bruksanvisning

9 September 2024

Swann SW231-WMX Bruksanvisning

9 September 2024

Swann ADS-466 Bruksanvisning

8 September 2024

Swann Enforcer SWPRO-4KMQB Bruksanvisning

6 September 2024

Swann SWVID-PENBL4 Bruksanvisning

2 September 2024

övervakningskamera Manualer

Nyaste övervakningskamera Manualer

Philips B120E Bruksanvisning

16 Januari 2025

Dahua Technology Pro IPC-HDPW5442G-Z Bruksanvisning

10 Januari 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Bruksanvisning

8 Januari 2025

Hikvision IDS-2CD7526G0-IZHSY Bruksanvisning

8 Januari 2025

Hikvision DS-2CD2163G0-I(S) Bruksanvisning

8 Januari 2025

Hikvision DS-2CD2H83G1-IZS Bruksanvisning

8 Januari 2025

Speco Technologies O5LB1 Bruksanvisning

8 Januari 2025

ZKTeco AntarVis 2.0 Bruksanvisning

8 Januari 2025

Speco Technologies O2P30X Bruksanvisning

8 Januari 2025

TP Link InSight S345ZI Bruksanvisning

8 Januari 2025