Tripp Lite SRCABLETRAY Bruksanvisning

Läs nedan 📖 manual på svenska för Tripp Lite SRCABLETRAY (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
1
Owners Manual
WARRANTY
REGISTRATION
Visit www.tripplite.com/warranty
today to register the warranty for
your new Tripp Lite product. You’ll be
automatically entered into a drawing for a
chance to win a FREE Tripp Lite product!
SmartRack Accessories
Models: SRCABLETRAY, SRCABLETRAYEXP
1 – Introduction
3 – SRCABLETRAY Installation
1-2 Tools Required
4-1 One Expansion Section
5 – Storage and Service
1-1 Parts List
4 – SRCABLETRAYEXP Installation
2 – Important Safety Instructions
4-2 Two Expansion Sections
6 – Warranty and Warranty Registration
1111 W. 35th Street, Chicago, IL 60609 USA
+1.773.869.1234 • www.tripplite.com
2
2
2
2
3
3
3
4
4
4
Copyright © 2008 Tripp Lite. All trademarks are the sole property of their respective owners.
2
1 – Introduction
2 – Important Safety Instructions
SRCABLETRAY provides roof-mounted cable routing and power/data cable segregation for Tripp Lite’s SmartRack Enclosures.
SRCABLETRAYEXP provides vertical expansion for SRCABLETRAY. (SRCABLETRAY also provides secure mounting points for Tripp
Lite’s SRCABLELADDER accessory, sold separately. SRCABLELADDER allows cable bundles to span aisles and/or spaces between
enclosures. See the SRCABLELADDER manual for more information.)
Install in a controlled indoor environment, away from moisture, temperature extremes, ammable liquids and gasses, conductive
contaminants, dust and direct sunlight.
Provide suitable grounding in accordance with all applicable electrical wiring regulations.
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life
support equipment or to signi cantly affect its safety or effectiveness is not recommended. Do not use this equipment in the presence of a
ammable anesthetic mixture with air, oxygen or nitrous oxide.
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that must be followed during the installation and operation of the products described in this
manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may invalidate the warranty and
cause property damage and/or personal injury.
Phillips Screwdriver
13 mm Open-End Wrench or Crescent Wrench (For SRCABLETRAY installation only.)
If anything is missing, call Tripp Lite for assistance at +1.773.869.1234. Note: SRCABLETRAY and SRCABLETRAYEXP are sold separately.
SRCABLETRAY
Trough Section (1)
Support Sections (2)
#8-32 x 1/4 Phillips Screws (8)
M6 Lock Washers (4)
M6 Hex Nuts (2)
24-inch Ground Cable (1)
SRCABLETRAYEXP
Expansion Sections (2)
#8-32 x 1/4 Phillips Screws (8)
1-1 Parts List
1-2 Tools Required
A1 A2
C1
E1
E1
F1
B1
B1
B2
A2
D1
D1
F1
C1
B2
A1
3
3 – SRCABLETRAY Installation
Note: You can remove the roof panel to aid installation, but this step is not required.
Assemble the cable tray by attaching the support sections A to
the trough section B with the included screws. Note: The support
sections should be attached inside the anges of the trough
section, not outside.
Insert the tabs C at one side of the cable tray into the matching
roof panel slots D. (Several sets of slots are compatible, allowing
you to adjust the cable tray’s position to match your preference.)
Compress the unattached cable tray support section A until you
can insert the remaining tabs E into the matching roof panel
slots F. When you release pressure from the cable tray support
sections, they will expand to provide a secure t.
Use the included hex nut G and lock washers H to connect one
end of the included ground cable I to a grounding post J at
the corner of the cable tray. Connect the other end of the ground
cable to the metal frame of the rack enclosure. (Follow the ground
wires connected to the rack enclosure’s doors to locate several
convenient ground connection points on the frame.)
1
1
2
3 4
A
C
C
DD
A
B
E
E
F
F
G
J
I
4 – SRCABLETRAYEXP Installation
Note: You must install SRCABLETRAY before installing SRCABLETRAYEXP. SRCABLETRAYEXP includes two expansion sections; you may
install one or both, depending on your needs.
4-1 One Expansion Section
Attach the expansion section A to the cable tray B with the
included screws.
1
1
A
B
34
2
H
H
TO

Produktspecifikationer

Varumärke: Tripp Lite
Kategori: Inte kategoriserad
Modell: SRCABLETRAY

Behöver du hjälp?

Om du behöver hjälp med Tripp Lite SRCABLETRAY ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Tripp Lite Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer